BeschreibungAlle Instrumente (Skalen und Anzeigen) leuchten auf, wenn der Zundschlussel in Fahrstellung MAR gedreht wird.Im "Nacht"-Betrieb (Standlicht ein) kann die Helligkeit in 3 Stufen uber einen au?eren Regler eingestellt werden.Bei der Version Sport mit wei?en Skalen, sind diese nicht beleuchtet, wenn der Zundschlussel auf MAR steht, sondern nur bei eingeschaltetem Standlicht.Diese Beleuchtungslogik wird durch ein Tachomodul geregelt, das die Beleuchtung des Drehzahlmoduls und des mittleren Instruments steuert.Das Check Control Instrument wird direkt von der elektronischen Vorrichtung im Inneren beleuchtet.Der Regelknopf ist links von den Instrumenten angebracht, zusammen mit dem Nullsteller des Kilometerzahlers und mit dem Regelwiderstand zur Einstellung der Scheinwerfer.Der Stromkreis aller Instrumente ist durch eine eigene Sicherung abgesichert, die neben dem Verteiler liegt.
Funktionsbeschreibung Der Tacho E10 (Pin 10 des Steckers A) wird uber den Zundschalter (INT) durch die Leitung der Sicherung F4B11 im Zusatzverteiler B98B (ab 2/99) versorgt. Analog der Drehzahlmesser E15 (an Pin 15 des Steckers A) und das mittlere Instrument E20 (Pin 1). Von der Helligkeitsregelung H10 kommt ein Massesignal zu Pin 6 des Steckers B von E10 . Au?erdem erhalt dieser ein Signal fur Standlicht EIN an Pin 5 des Steckers B ( 3260832SieheE2010STANDLICHT / KENNZEICHENLEUCHTE ). Auf Grund der von der inneren Elektronikvorrichtung erarbeiteten Logik, sendet der Tacho E10 das Signal zur Beleuchtung an die anderen Instrumente: an das mittlere Instrument E20 (Pin 7) von Pin12 des Steckers A und an den Drehzahlmesser E15 (3 des Stekkers B) von Pin 4 des Steckers B. Der Schalter H10 wird beleuchtet, wenn das Standlicht eingeschaltet wird, und zwar durch die Leitung vom Schalter im Lenkstockhebel H5 .
0Ausbau201Wiedereinbau21Die Teile entfernen, die denZugang zum Masse-Sammelanschlu? verhindern.1. Die Schraube abschrauben.2. Den Masse-Sammelanschlu? trennen.2018618
0Ausbau201Wiedereinbau211. Schrauben Sie die Schraube ab.2. Entfernen Sie den rand (2a), indem Sie ihn von den Halteklammern(2b) anheben.3. Schrauben Sie die Schrauben ab.4. Heben Sie den tachometer/Kilometerzahler (4a) von der Halterung(4b) und verschieben Sie sie.5. Trennen Sie die elektrischen Anschlusse (5a, 5b).2018847
5560B03
0Ausbau201Wiedereinbau211. Schrauben Sie die Schraube ab..2. Entfernen Sie den Rahmen (2a), indem Sie ihn aus der Haltefeder(2b) anheben.3. Schrauben Sie die Schrauben ab.4. Heben Sie den Drehzahlmesser (4a) aus der Halterung (4b) undverschieben Sie ihn.5. Trennen Sie die elektrischen Anschlusse (5a, 5b).2018848
5560B06
0Ausbau201Wiedereinbau21Fur den Austausch der Gluhbirnendes Tachometers/Kilometerzahlers fahren Sie wie folgt fort:3265561-5560B02Km- bzw. Meilenzahler a.u.e.1. Ziehen Sie die Lampenfassung der Instrumentenbeleuchtung (1a)oder die Lampenfassung der Displaybeleuchtung (1b) durch Drehenheraus.2. Ziehen Sie die Gluhbirne aus der Lampenfassung (Druckansatz).2018849
0Ausbau201Wiedereinbau21Fahrzeug auf die Hebebuhnefahren und anheben.1. Unter der linken vorderen Radaufhangung die Befestigungsmutterdes Pleuelhebels losen.2. Pleuelhebel vom Sensorhebel losen.3. Befestigungsschrauben des Halters losen.4. Sensor mit Halter verschieben.5. Elektrischen Anschluss abklemmen und Sensor mit Halter entfernen.2018817
5540C44
0Ausbau201Wiedereinbau21Fahrzeug auf die Hebebuhnefahren und anheben.1. Unter der linken vorderen Radaufhangung die Befestigungsmutterndes Pleuelhebels losen.2. Pleuelhebel abnehmen.2018819
5540C46
0Ausbau201Wiedereinbau21Fahrzeug auf die Hebebuhnefahren und anheben.1. Unter der linken hinteren Radaufhangung die Befestigungsmutterdes Pleuelhebels losen.2. Pleuelhebel vom Sensorhebel losen.3. Befestigungsschraube des Sensors losen.4. Den Sensor (4a) zur Seite schieben, die elektrische Verbindung(4b) abklemmen und dann den Sensor abnehmen.2018820
5540C48
0Ausbau201Wiedereinbau21Fahrzeug auf die Hebebuhnefahren und anheben.1. Unter der linken hinteren Radaufhangung die Befestigungsmutterndes Pleuelhebels losen.2. Pleuelhebel abnehmen.2018821
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.