BeschreibungWenn die Bedingungen es verlangen, schaltet die Elektronik der Klimaanlage den Kreis der Luftkuhlung und -entfeuchtung ein, indem sie den Kompressor der Klimaanlage betatigt.Durch die linke Taste der Schaltergruppe der Klimaanlage wird die Funktion des Luftkuhlkreises gewahlt; bei gedruckter Taste leuchtet die entsprechende LED.Die Funktion des Luftkuhlkreises wird auch automatisch eingeschaltet (ohne Drucken der Taste) mit Zundschlussel auf MAR, wenn die Temperatur der Luft aus den Dusen niedriger als die der Au?entemperatur ist.Die oben genannte Taste wahlt die Funktion des Luftkuhlkreises; aber das effektive Einschalten des Kompressors wird bei niedrigen Au?entemperaturen abgeschaltet. Fur weitere Einzelheiten siehe 3260020Funktionsweise5040GEHAUSE UND BAUTEILE DER KLIMAANLAGE . Der Kompressor kann auch durch den 4stufigen Druckschalter abgeschaltet werden oder durch die Motorsteuerung, die in Abhangigkeit von der jeweiligen Motorisierung verschiedene Motorbetriebsstrategien durchfuhrt ( 3259938Funktionsweise1060KRAFTSTOFFVERSORGUNG DIESELEINSPRITZUNG ). Die Stromversorgung des Kompressors wird uber ein eigenes Relais angelegt, das im Motorraum in der Nahe der Batterie liegt.Der Stromkreis des Relaiskontakts ist durch eine eigene Sicherung und von einem Relais im Verteiler uber das Zundschloss abgesichert.Der Stromkreis wird durch eine fliegende Sicherung geschutzt, die hinter dem Zundschloss auch fur andere Schaltkreise benutzt wird.
Funktionsbeschreibung Das Relais J20 kontrolliert den Stromkreis zum Einschalten des Kompressors. Das Relais wird 'uber das Zundschloss' (INT/A) und das Relais R1 versorgt und durch die Sicherung F15 geschutzt: Relais und Sicherung liegen im Verteiler B1. Die Spule wird uber die Leitung mit der Sicherung F2 im Zusatzverteiler B98A versorgt. Uber das Hauptrelais der Einspritzung J10 wird das Relais durch ein Massesignal der Motorelektronik M10 erregt: Auf diese Weise versorgt es den Elektromagneten zum Einschalten des Kompressors der Klimaanlage L20 mit einer Spannung von 12 V. Die Elektronik der Klimaanlage M70 (Pin 11 des Steckers A) gibt das Freigabesignal zum Einschalten des Kompressors an den vierstufigen Druckwachter K10. Sind die Druckwerte des Kreises korrekt, gelangt das Signal des Druckwachters zur Motorelektronik M10 - Pin 60 des Steckers A. Aufgrund der internen Kontrolllogik gibt die Elektronik M10 - Pin 18 des Steckers A - den effektiven Befehl zum Einschalten des Kompressors durch Erregung des Relais J20.
0Ausbau201Wiedereinbau21Die Teile entfernen, die denZugang zum Masse-Sammelanschlu? verhindern.1. Die Schraube abschrauben.2. Den Masse-Sammelanschlu? trennen.2018618
0Ausbau201Wiedereinbau21Das Fahrzeug auf die Hebebuhne fahren.Schraube des Haltebugels auf der Batteriehalterung losen.Batterie mit Riemen vom Haltebugel abnehmen.
5530B14
769768768
5530B18
Folgende Hinweisebeachten769Bei Batterien mit optischem Standmesserist es moglich, den Stand des Elektrolyts und den Ladezustand derBatterie je nach Farbe des optischen Anzeigers zu ermitteln.eine klare und weisse Farbe zeigt einenunausreichenden Elektrolytstand an: mit destilliertem Wasser auffulleneine dunkle Farbe ohne grunes Feld zeigteinen korrekten Elektrolytstand mit niedriger Batterieladung an:die Batterie muss geladen werden.eine dunkle Farbe mit grunem Bereich inder Mitte zeigt einen korrekten Elektrolyt- und Ladezustand der Batteriean: es muss keinerlei Eingriff durchgefuhrt werden. Fur weitere Einzelheiten siehe 3265485SieheUntergruppe5530 STROMERZEUGUNG . 768Wie folgt vorgehen:Leerlaufspannung der Batterie mit dem vomKD empfohlenen Me?gerat 'MICRO 360' messen.Je nach gemessenem Spannungswert, der denLadezustand anzeigt, wie folgt vorgehen: Bei Leerlaufspannung unter 12,10 V dieBatterie ersetzen ( 32654945530B10Batteriea.u.e. ). Bei Leerlaufspannung uber 12,10 V, aberunter 12,50 V die Batterie nachladen ( 32654955530B14Batterie laden ). Bei Leerlaufspannung uber 12,50 V istdie Batterie geladen.Ggf. den Saurestand wie folgt erganzen:Band mit den Verschlussen abziehen.Destilliertes, entionisiertes Wasser nachfullen.Vorsicht, da? keine Spritzer nach au?en verursacht werden.768
5530B22
0Ausbau201Wiedereinbau21Das Fahrzeug auf die Hebebuhnepositionieren.1. Den Deckel des Motorraums aufmachen und die negative Klemme derBatterie abklemmen.2. Den Massekontakt auf dem Langstrager trennen.3. Das Fahrzeug heben und den Massekontakt auf dem Wechselgetriebetrennen.4. Das Fahrzeug niedriger bringen und das Massekabel der Batterieentfernen.2018767
5030B26
769
5030B40
0Ausbau201Wiedereinbau21Minuskabel von der Batterie abklemmen.1. Den Deckel offnen.2. Mutter lockern und ABS-Kabel abklemmen.3. Mutter lockern und Kabel vom Anlasser abklemmen.4. Klammer und Befestigungsschrauben des Gehauses losen.5. Mutter der Plusklemme der Batterie lockern.2018769
5530B52
0Ausbau201Wiedereinbau213265494-5530B10Batterie a.u.e.Luftleitkastenmuffe vom Haltebugel amKorb befreien.Abdeckung der Relais entfernen.1. Relais aushangen und aus dem Batteriekorb entfernen.2. Befestigungsmutter des Verankerungsbugels des Luftfilters amBatteriekorb losen.3. De beiden Befestigungsmuttern (3a) losen und den Haltebugel(3b) der elektrischen Steckverbinder/Kabel zur Seite schieben.4. Den Gaszug von der Befestigung am Bugel losen.2018771
0Ausbau201Wiedereinbau211. Mutter abschrauben.2. Mit einem dreiarmigen Abzieher durch die drei Offnungen (2a)von der Welle (2b) die Dampfungsplatte (2c) abziehen.3. Abstandstucke abnehmen.2018450
0Ausbau201Wiedereinbau21Das Fahrzeug auf die Hebebuhne fahren.768 Kaltemittel ablassen ( 3265370-5040A10KUHLKREIS der Klimaanlage- Entwassern und Auffullen ). 1. Von der rechten Seite des Motorraums aus die Verbindung der Leitungungenvom Verdampfer zum Kompressor losen. 7692018466
0Ausbau201Wiedereinbau21 Kaltemittel ablassen ( 3265370-5040A10KUHLKREIS der Klimaanlage- Entwassern und Auffullen ). 7681. Die Schrauben (1a) losen und den Lenkflussigkeitsbehalter(1b) zur Seite schieben.2. Halteschellen losen.3. Unterdruckleitung des Bremskraftverstarkers entfernen.2018472
0Ausbau201Wiedereinbau21Minuskabel (-) von der Batterie abklemmen.1. Elektrischen Anschlu? des Hei?filmluftmengenmessers abklemmen. Am Batteriekorb befestigte Relais zur Seiteschieben.2. Luftzuleitung zum Drosselklappenstutzen vom Luftmengenmessertrennen.3. Muttern (3a) abschrauben, Halbringe (3b) und Luftmengenmesser(3c) entfernen .2013556
1056B10
0Ausbau201Wiedereinbau21Prufen, dass der Zundschlussel auf 'STOP'steht, dann Minuskabel (-) von der Batterie abklemmen.1. Elektrischen Anschluss vom Luftmengenmesser abklemmen.Am Batteriekorb befestigte Relais zur Seiteschieben.2. Luftzuleitung zum Drosselklappenstutzen vom Luftmengenmessertrennen.3. Muttern (3a) abschrauben, Halbringe (3b) und Luftmengenmesser(3c) entfernen .2013557
1056B17
0Ausbau201Wiedereinbau21Prufen, dass der Zundschlussel auf "STOP"steht, dann Minuskabel (-) von der Batterie abklemmen.1. Die Oldampfruckfuhrungsleitung vom rechten Zylinderkopf abziehen.2. Balgstutzen vom Drosselklappenstutzen trennen und seitlich ablegen.2013558
0Ausbau201Wiedereinbau21- 1072B42 Linken 0der rechten ansaugkrummer a.u.e. 767Vor allen Arbeiten an derKraftstoffversorgung den Systemdruck mit Hilfe des Werkzeugs Nr.1.870.684.000 ablassen, das an das entsprechende Ventil am Kraftstoffverteilerrohrangebracht wird.1. Kraftstoffzuleitung losen, dann Leitung entsprechend verschlie?en,um das Austreten von Kraftstoff zu verhindern.2. Elektrische Anschlusse von den elektronischen Einspritzdusenabklemmen.3. Schrauben (3a) herausschrauben und Kraftstoffleitung (3b) komplettmit Elektroeinspritzventilen (3c) entfernen.2013562
0Ausbau201Wiedereinbau211. Sicherungen (1a) entfernen und Elektroeinspritzventile (1b) vomKraftstoffverteilerrohr abnehmen.2. O-Ringe von den Elektroeinspritzventilen entfernen.2013564
0Ausbau201Wiedereinbau21Prufen, ober Zundschlussel auf 'STOP'steht, dann Minuskabel (-) von der Batterie abklemmen.1. Vom Innenraum aus die Schrauben (1a) herausschrauben und dieSchutzabdeckung (1b) der Einspritz-/Zundsteuerung entfernen.2. Elektrische Anschlusse von der Steuerung der Einspritz-Zundanlageabklemmen.767Reihenfolge des Abklemmenseinhalten: D - E - F - C - B - A.3. Muttern (3a) abschrauben und die Steuerung fur Einspritzung/Zundung(3b) entfernen.2013565
1056B90
0Ausbau201Wiedereinbau21Minuskabel (-) von der Batterie abklemmen.Fahrzeug anheben.1. Elektrischen Anschlu? des Elektromagneten zum Einschalten desKompressors der Klimaanlage abklemmen.2013568
1056B14
0Ausbau201Wiedereinbau213264594-1048A34Schlauch Luftmengenmesser-Luftkasten a.u.e.1. E-Verbindung Leerlaufsteller trennen.2. Vom Drosselklappenstutzen die beiden Kuhlmitteleinla?- undAusla?leitungen (2a-.2b) vom Drosselklappenstutzen trennen.3. Elektrischen Anschlu? des Drosselklappenstellers (Potentiometer)abklemmen.4. Gaszug aushangen.Leitungen von den Befestigungen am Bugelunter dem Drosselklappen losen.5. Die vier Befestigungsschrauben (5a) herausschrauben und den Drosselklappenstutzen(5b) mit zugehoriger Dichtung entfernen.2014090
1056B15
0Ausbau201Wiedereinbau21Prufen, dass der Zundschlussel auf "STOP"steht, dann Minuskabel (-) von der Batterie abklemmen.3264717-1016A40Deckel fur Zundspulen am Zylinderkopf a.u.e.3264594-1048A34Schlauch Luftmengenmesser-Luftkasten a.u.e.Elektrischen Anschluss vom Stellglied desDrosselklappenstutzens mit integriertem M.D.S. abklemmen.1. Elektrische Anschlusse (1a) und (1b) von der Einspritz-Zundsteuerungund das Massekabel (1c) vom Drosselklappenstutzen mit integriertemM.D.S. abklemmen.2. Gaszug vom Drosselklappenstutzen mit integriertem M.D.S. aushangen.3. Kabel der Einspritzung-Zundung vom betreffenden Haltebugellosen.4. Schrauben (4a) herausschrauben und Drosselklappenstutzen mitintegriertem M.D.S. (4b) komplett mit Einspritz-Zundsteuerung (4c)entfernen.2014091
1056B19
0Ausbau201Wiedereinbau21Prufen, dass der Zundschlussel auf 'STOP'steht, dann Minuskabel (-) von der Batterie abklemmen.3264609-1056B82Steuergerat fur Einspritzung und Zundung a.u.e. . 1. Das Massekabel von der Halterung der Einspritzelektronik losen.2. Oldampfruckfuhrung von der Faltenmuffe abziehen.3. Die Schellen lockern und das zweite Stuck der Faltenmuffe vomBugel losen und abnehmen.4. Den elektrischen Anschluss (4a) vom Drosselgehause mit integriertemD.V.L. abklemmen und die Verkabelung von der Schelle (4b) losen.2014095
1056B40
0Ausbau201Wiedereinbau21Minuspol der Batterie abklemmen.1. Elektrischen Anschlu? des Mischlufttemperatursensors abklemmen. 2. Schelle (2a) losen, Luftstutzen (2b) vom Drosselklappenstutzenabnehmen und zur Seite schieben.3. Die beiden Schrauben des Lenkflussigkeitsbehalters herausschraubenund Behalter zur Seite schieben.2014098
1056B43
0Ausbau201Wiedereinbau21Minuspol der Batterie abklemmen.1. Elektrischen Anschlu? vom Konstantleerlaufdrehzehalsteller abklemmen.2. Die beiden Befestigungsschrauben herausschrauben und den Drosselklappenstellerentfernen, dabei die betreffende Dichtung abnehmen.2014100
1056B46
0Ausbau201Wiedereinbau21Minuspol der Batterie abklemmen.1. Elektrischen Anschlu? des Mischlufttemperatursensors abklemmen. 2. Sauglufttemperaturfuhler vom Luftverteilerstutzen losen undentfernen.2014101
1056B48
0Ausbau201Wiedereinbau21Minuspol der Batterie abklemmen.
1056B60
0Ausbau201Wiedereinbau21Minuskabel von der Batterie abklemmen.
1056B87
0Ausbau201Wiedereinbau21Prufen, ob die Zundung ausgeschaltetist (Zundschlusselstellung 'STOP') und anschlie?end das Minuskabel (-)der Batterie abklemmen.1. Die elektrischen Anschlusse (1a) und (1b) von der Einspritz-Zundelektroniktrennen.2. Die elektrischen Verkabelungen von der Sicherung an der Halterungder Anlage befreien.2014110
1056B89
0Ausbau201Wiedereinbau21Prufen, dass der Zundschlussel auf 'STOP'steht, dann Minuskabel (-) von der Batterie abklemmen.3264609-1056B82Steuergerat fur Einspritzung und Zundung a.u.e. . 1. Das Massekabel von der Halterung der Einspritzelektronik losen.2. Oldampfruckfuhrung von der Faltenmuffe abziehen.3. Die Schellen lockern und das zweite Stuck der Faltenmuffe vomBugel losen und abnehmen.4. Den elektrischen Anschluss (4a) vom Drosselgehause mit integriertemD.V.L. abklemmen und die Verkabelung von der Schelle (4b) losen.2014117
Elektronische Kontrolle der Druckpumpe fur Diesel-Einspritzung
1060G10
0Ausbau201Wiedereinbau213264849-1048A50Leitung am Turbolader a.u.e. Der Zundschlussel mu? auf STOP stehen.Minuspol (-) der Batterie abklemmen (siehe Arbeit 32654945530B10Batterie a.u.e. ). 1. Schrauben (1a) herausschrauben und den Relaishaltebugel (1b)vom Batteriekorb abnehmen.2. Elektrischen Anschlu? des Luftmengenmessers abklemmen.3. Muttern (3a) abschrauben und die Befestigungsplatten (3b) entfernen.4. Luftmengenmesser (4a) komplett mit Luftmengenmesserstutzen zurLufteinla?leitung des Turboladers (4b) und Stutzen vom Filter zumLuftmengenmesser (4c) entfernen.2015135
1060G14
0Ausbau201Wiedereinbau213265494-5530B10Batterie a.u.e.1. Elektrischen Anschlu? des Wassertemperaturfuhlers abklemmen.2. Wassertemperaturfuhler abschrauben und entfernen.2015136
1060G16
0Ausbau201Wiedereinbau21Minuskabel (-) von der Batterie abklemmen. 1. Elektrischen Anschlu? vom Uberdrucksensor abklemmen.2. Schraube (2a) herausschrauben und Uberdruckfuhler (2b) entfernen.2015137
1060G18
0Ausbau201Wiedereinbau21 Der Zundschlussel mu? auf STOP stehen.Minuspol (-) der Batterie abklemmen (siehe Arbeit 32654945530B10Batterie a.u.e. ). 1. Elektrischen Anschlu? des Wassertemperaturfuhlers abklemmen.2. Kraftstofftemperaturfuhler vom Kraftstoffsammelrohr abschraubenund entfernen.2015138
1060G20
0Ausbau201Wiedereinbau21Das Fahrzeug auf die Hebebuhne fahren.Fahrzeug anheben. Der Zundschlussel mu? auf STOP stehen.Minuspol (-) der Batterie abklemmen (siehe Arbeit 32654945530B10Batterie a.u.e. ). 1. Rucklaufrohr des kondensierten Ols von der Olwanne trennen.OT- und Drehzahlsensor abklemmen.2. Schraube (2a) herausschrauben und OT- und Drehzahlfuhler (2b)entfernen.2015139
0Ausbau201Wiedereinbau21Prufen, dass der Zundschlussel auf 'STOP'steht, dann Minuskabel (-) von der Batterie abklemmen. Mit dem Ausbau fortfahren 3264823-1016A10Gerauschdammhaubea.u.e. . 1. Elektrischen Anschluss des Kraftstoffdruckfuhlers am Kraftstoffverteilerrohranklemmen.2. Kraftstoffdrucksensor vom Kraftstoffverteilerrohr abschraubenund entfernen.2068748
0Ausbau201Wiedereinbau21 Der Zundschlussel mu? auf STOP stehen.Minuspol (-) der Batterie abklemmen (siehe Arbeit 32654945530B10Batterie a.u.e. ). Elektrischen Anschlu? des Bremspedalschalters abklemmen.Schalter am Bremspedal drehen und entfernen.
1060G42
0Ausbau201Wiedereinbau21 Der Zundschlussel mu? auf STOP stehen.Minuspol (-) der Batterie abklemmen (siehe Arbeit 32654945530B10Batterie a.u.e. ). Elektrischen Anschlu? vom Kupplungspedalschalter abklemmen.Kupplungspedalschalter drehen und entfernen.
1060G50
0Ausbau201Wiedereinbau21 Mit dem Ausbau fortfahrens 3264823-1016A10Gerauschdammhaubea.u.e. . 1. Die Schelle (1a) lockern und den Luftzufuhrstutzen vom Warmetauscherzum Saugrohr (1b) auf der Seite des Drosselgehauses abnehmen. 2015145
0Ausbau201Wiedereinbau21 Mit dem Ausbau fortfahrens 3264823-1016A10Gerauschdammhaubea.u.e. . 1. Die Schelle (1a) lockern und den Luftzufuhrstutzen vom Warmetauscherzum Saugrohr (1b) auf der Seite des Drosselgehauses abnehmen.2015155
1060G70
0Ausbau201Wiedereinbau21Prufen, ob die Zundung ausgeschaltetist (Zundschlusselstellung 'STOP') und anschlie?end das Minuskabel (-)der Batterie abklemmen. Mit dem Ausbau fortfahrens 3264823-1016A10Gerauschdammhaubea.u.e. . 1. Die Schelle (1a) lockern und den Luftzufuhrstutzen vom Warmetauscherzum Saugrohr (1b) auf der Seite des Drosselgehauses abnehmen.2015161
1060G72
0Ausbau201Wiedereinbau21Prufen, ob die Zundung ausgeschaltetist (Zundschlusselstellung 'STOP') und anschlie?end das Minuskabel (-)der Batterie abklemmen. Mit dem Ausbau fortfahrens 3264823-1016A10Gerauschdammhaubea.u.e. . 1. Die Schelle (1a) lockern und den Luftzufuhrstutzen vom Warmetauscherzum Saugrohr (1b) auf der Seite des Drosselgehauses abnehmen.2015169
1060G80
0Ausbau201Wiedereinbau21 Der Zundschlussel muss auf 'STOP' stehen.Minuspol (-) der Batterie abklemmen (siehe Arbeit 32654945530B10Batterie a.u.e. ). Vom Innenraum aus im Bereich des vorderenRadkastens auf der Beifahrerseite die Schraube und die Mutter abschraubenund die Abdeckung der Steuerung entfernen.Die betreffenden Sicherheitshebel drehenund die elektrischen Anschlusse abklemmen.Muttern abschrauben und die Steuerung derelektronischen Dieseleinspritzanlage entfernen.
1060G88
0Ausbau201Wiedereinbau21Prufen, dass der Zundschlussel auf 'STOP'steht, dann Minuskabel (-) von der Batterie abklemmen.1. Mutter (1a) losen und Schutzdeckel (1b) entfernen.2. Relais der Dieseleinspritzanlage entfernen.2015179
1060G90
0Ausbau201Wiedereinbau21Das Fahrzeug auf die Hebebuhne fahren. Mit dem Ausbau fortfahren 3264823-1016A10Gerauschdammhaubea.u.e. . Prufen, dass der Zundschlussel auf 'STOP'steht, dann Minuskabel (-) von der Batterie abklemmen. Mit dem Ausbau fortfahren 3266031-7055B54untere Motorabdeckung/ Schutz a.u.e. . Mit dem Ausbau fortfahren 3264931-1076B70Auspuffrohr vor demKatalysator a.u.e. . 1. Elektrischen Anschluss des Schalters fur die Oldruckkontrollleuchteabklemmen.2. Elektrischen Anschluss des Motorolstandfuhlers abklemmen.3. Elektrische Anschlusse des Drehzahlsensors abklemmen.2069114
0Ausbau201Wiedereinbau211. Befestigungsschrauben des Motors losen.2. Elektrischen Anschluss vom Motor abziehen.3. Motor (3a) entfernen, indem das Zahnrad (3b) von der Nockenzahnstangegelost wird.2018552
0Ausbau201Wiedereinbau211. Befestigungsschrauben des Motors losen.2. Elektrische Anschlusse (2a, 2b, 2c, 2d, 2e) abklemmen.3. Motor (3a) entfernen und von den Verbindungen (3b) befreien2018560
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.