| G182 | Gearbox input speed sender |
| G487 | Gear selector movement sensor 1 |
| G488 | Gear selector movement sensor 2 |
| G510 | Temperature sender in control unit |
| J623 | Engine control unit |
| J743 | Mechatronic unit for dual clutch gearbox |
| SB17 | Fuse 17 on fuse holder B |
| SB18 | Fuse 18 on fuse holder B |
| SC25 | Fuse 25 on fuse holder C |
| T25 | 25-pin connector |
| T94 | 94-pin connector |
| V401 | Hydraulic pump motor |
| 85 | Earth connection 1, in engine compartment wiring harness |
| 655 | Earth point, on left headlight |
| U8 | Positive connection (15a), in automatic gearbox wiring harness |
| * | Only models with Euro 6 emission standard |
| *2 | Only for American markets |
| F319 | Selector lever locked in position P switch |
| G270 | Gearbox hydraulic pressure sender |
| G641 | Gearbox input speed sender 3 |
| J527 | Steering column electronics control unit |
| J587 | Selector lever sensors control unit |
| J743 | Mechatronic unit for dual clutch gearbox |
| J764 | Control unit for electronic steering column lock |
| N110 | Selector lever lock solenoid |
| SC14 | Fuse 14 on fuse holder C |
| SC20 | Fuse 20 on fuse holder C |
| T2p | 2-pin connector |
| T10s | 10-pin connector, under selector lever |
| T16l | 16-pin connector |
| T16v | 16-pin connector |
| 43 | Earth point, lower part of right A-pillar |
| 366 | Earth connection 1, in main wiring harness |
| 388 | Earth connection 23, in main wiring harness |
| A189 | Positive connection 5 (30a) in dash panel wiring harness |
| A199 | Positive connection 4 (15a) in dash panel wiring harness |
| B114 | Connection (inhibitor switch), in interior wiring harness |
| * | Only models with entry and start authorisation |
| *2 | According to equipment |
| *3 | Only models with no entry and start authorisation |
| E313 | Selector lever |
| G489 | Gear selector movement sensor 3 |
| G490 | Gear selector movement sensor 4 |
| G617 | Clutch travel sender 1 |
| G618 | Clutch travel sender 2 |
| J519 | Onboard supply control unit |
| J587 | Selector lever sensors control unit |
| J743 | Mechatronic unit for dual clutch gearbox |
| L101 | Selector lever display illumination bulb |
| N433 | Valve 1 in sub-gearbox 1 |
| N434 | Valve 2 in sub-gearbox 1 |
| N435 | Valve 3 in sub-gearbox 1 |
| N440 | Valve 4 in sub-gearbox 2 |
| T10s | 10-pin connector, under selector lever |
| T10v | 10-pin connector |
| T25 | 25-pin connector |
| T52b | 52-pin connector |
| Y6 | Selector lever position display |
| B340 | Connection 1 (58d), in main wiring harness |
| B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
| B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
| G612 | Gearbox input speed sender 2 |
| G632 | Gearbox input speed sender 1 |
| JX1 | Power and control electronics for electric drive |
| J285 | Control unit in dash panel insert |
| J533 | Data bus diagnostic interface |
| J743 | Mechatronic unit for dual clutch gearbox |
| N436 | Valve 4 in sub-gearbox 1 |
| N437 | Valve 1 in sub-gearbox 2 |
| N438 | Valve 2 in sub-gearbox 2 |
| N439 | Valve 3 in sub-gearbox 2 |
| T16 | 16-pin connector, on diagnostic connection |
| T20 | 20-pin connector |
| T25 | 25-pin connector |
| T28jx | 28-pin connector |
| T32 | 32-pin connector |
| A76 | Connection (K-diagnosis wire), in dash panel wiring harness |
| B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
| B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
| B708 | Connection 1 (dash panel insert CAN bus high) in main wiring harness |
| B709 | Connection 1 (dash panel insert CAN bus low) in main wiring harness |
| * | From June 2013 |
Русский
