DescriptionThe radio receiver node, the heater/climate control system controls, the cigar lighter/current socket and the instrument panel contain one or more bulbs for lighting the instruments. The power supply for the bulbs is provided directly by the body computer node, only after the side lights have been switched on.The lights inside the instrument panel do, however, remain on at a minimum level even with the side lights switched off.
Functional description The body computer node M001 receives a negative signal (with reference to earth C020 connector B) at pin 2 connector P that the side lights are switched on coming from the steering column switch unit H005 (see wiring diagram E2010).Having received the signal, the body computer:from pin 9 connector L, sends the '+lighting' signal to the short circuiting coupling D097E, which distributes the signalto the radio receiver node M094, at pin 6 connector A;to the cell phone preparation coupling D075, at pin 8;to the heater/air conditioning system controls lighting G045A and G045B.the '+lighting' signal is sent from pin 7 connector E to the cigar lighter/current socket P050;767 Earth C020 is fastened to the passenger compartment floor and is located near the right front wheel arch (footwell area).The body computer node communicates that the side lights are switched on via the CAN:to the instrument panel E050, from pins 35, 36, connector I;to the climate control system control unit M070 (for versions with automatic climate control), from pins 3, 8 connector O.767 Coupling D001 is housed, in the passenger compartment, in the lower part of the right front pillar, near the door cable duct, passenger side.Having received the signal that the side lights are on, the instrument panel and the radio receiver node manage the switching on of their own LEDs for lighting up the instruments.
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Remove the cable pass on the right side of the vehicle from itsseating and open the cover.2. Remove the adhesive tape (2a) present on the wiring (2b) andrelease the windscreen/rear window washer tubes (2c).Release the wiring from the cable pass.Following the same procedure, release thewiring from the cable pass on the left of the vehicle.2046933
5505C34
768769
5505C35
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disconnect the aerial coaxial cable connections.2. Disconnect the electrical connections (2a), (2b), (2c), (2d),(2e) and (2f).2046939
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753183-7040A23frame of instrument panel on facia - r r1. Undo the retaining bolts.Partially remove the instrument panel.2. Disconnect the electrical connection.3. Remove the instrument panel.2046983
767It is not possible toorder a single lock barrel or to order barrels using only the partcode. When ordering barrels, observe the special procedure set outin operation 5580 - Special Accessories. 768769
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Disengage the fixing lugs (1a) and remove the cover (1b).2046919
5505A32
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753188-7040A37fuse box cover - r r1. Undo the retaining bolts.Disconnect the electrical connections.2. Remove the body computer.2046922
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.Disconnect the electrical connection.1. Undo the retaining bolts.2. Remove the air conditioner air distribution flap motor.2046903
5040D77
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.1. Release and remove the bottom right trim.2046905
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Open the fixing bolt cover plugs.2. Undo the retaining bolts.3. Remove the grab handle.2047313
7065C31
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo the retaining bolts.2. Remove the interior grab handle mounting.2047314
7065C34
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Undo retaining bolts2. Release the sun visor and remove it.3. Undo retaining bolts4. Remove the mount.2047315
7065C68
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting211. Raise the mounting (1a) for the interior rear view mirror releasingit upwards from the retaining plate (1b) secured to the glass.2047316
7065C69
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21The following procedure illustratesthe refitting of the plate for the rear view mirror on the glassbecause, if it is correctly secured, it cannot be removed.767Do not attempt to remove the platefor the rear view mirror from the glass because this could damagethe actual glass.
7065C73
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.2753327-7065C84front power point housing - r r1. Release the retaining (1a) from the housing (1b) and extractthe ring nut (1c).2. Extract the bulb holder with the bulb.3. Extract the bulb, which is a press fit, from the bulb holder.2047318
7065C84
<anchor>0</anchor><span>Removing</span><icon><imageid>20</imageid></icon>1Refitting21Disconnect the battery negativeterminal.1. Extract the current socket housing (1a) using the special tool(1b).767The tool should engage in therecesses (1c) of the current socket housing.2. Disconnect the electrical connection.Remove the current socket housing.2047319
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
