DescriptionThe sunroof offers extra ventilation for the interior compartment and ensures a rapid air exchange, if required, thus increasing passenger comfort.The system is operated by a switch, located near the front courtesy light, which controls a motor with two different operating modes: press one end of the switch to raise the roof in 'compass' fashion, and press the other end of the switch to slide the roof open and so pull the blind: when the switch is released, the roof stops in the position it is in at that moment.The entire system consists of a single unit which comprises:the control unit A, which manages the operation of the roof;tha actuating motor C;the control switch B;the end-of-travel switches D, located on a ring nut outside the motor, which stop the motor when the roof is fully open or closed. For more details, 3308564see DESCRIPTION AND OPERATION:7030SUN ROOF AND HOODThe sunroof circuit is protected by a specific fuse, and controlled by a relay which supplies other 'ignition-operated' services. The fuse is located inside the junction unit, and the relay is located on the right hand side of the facia.The sunroof can only be operated with the ignition on.
Functional description The sun-roof power supply comes from the ignition-operated line (INT/A) connected to relay R1 protected by fuse F13 : both are contained in junction unit B1 . This line protects the circuit and leads to sun-roof junction D45 , which is also connected to earth C15 . The switch is therefore active when the ignition is on (INT/A). The control unit controls engine movement according to switch position.
0Removing201Refitting213314824-5505A18multi-function controlunit - r r . 1. Undo the bolt (1a) and push back the junction unit as far asnecessary to disconnect the electrical connections (1b).767For precise identification ofthe electrical connections, see Wiring Diagrams Section.2. Remove the junction unit.2010592
0Removing201Refitting21 Make sure that the ignitionis off (STOP position), then disconnect the negative battery terminal(refer to op. 33148615530B10battery - r+r ). 1. Unscrew bolt (1a) and open fuse access cover (1b).2. Undo the bolt (2a) and remove the integrated multiservices unit(2b) after having disconnected the electrical connections (2c),(2d), (2e), (2f) and (2g).2010595
5505A29
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b) for theadditional junction unit.2071293
0Removing201Refitting213314864-5530B54battery cover - r+r . Make sure that the ignition key is in theOFF position.1. Disconnect the battery negative and positive terminals.2. Undo the bolt (2a) fixing the battery retaining bracket (2b).3. Remove the battery.2010647
5530B40
0Removing201Refitting213314864-5530B54battery cover - r+r1. Press and release the retainers (1a), then remove the cover (1b)for the supply box on the battery. 2071303
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.