ENGINE PERFORMANCE – Porsche 911 Turbo S 2011 – SYSTEM WIRING DIAGRAMS

ENGINE PERFORMANCE

3.6L

3.6L, Engine Performance Wiring Diagram (1 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.6L, Engine Performance Wiring Diagram (1 of 4) for Porsche 911 Turbo S 2011:

• (hfm1)
• (info not available)
• (left kick panel) relay support 1
• +5v vehicle
• A lock starter
• A/t
• Behind oxygen sensor catalytic converter bank 1
• Behind oxygen sensor catalytic converter bank 2
• Blower stage 2
• Bridge plug (relay support 1)
• Can high
• Can low 1
• Clutch interlock switch (top of clutch pedal assembly)
• Clutch switch
• Computer data lines system
• Cooling fans system
• Cooling water
• Current distributor (behind right side of dash)
• Dme control unit (left front of engine compt)
• Dme relay
• Dmtl-heating
• Electronic mufflers system
• Fuel pump
• Fuel pump 1
• Fuse f3 7.5a
• Fuse f4 20a
• Fuse f5 25a
• Fuse f6 25a
• Fuse f7 15a
• Fuse f7 80a
• Fuse f8 7.5a
• Fuses holder d
• Gnd
• Gp4 (center of support frame)
• Gp9 (right rear of engine compt)
• Ground
• Heated oxygen 1
• Heated oxygen 2
• Hot at all times
• Lsf heater nk
• Lsf heater nk b2
• Lsf sig
• Lsf signal nk b1
• Lsu comp
• Lsu ground vk b1
• Lsu heater
• Lsu pumping
• M/t
• Pas control unit
• Pdk control unit
• Pedal sens
• Purge fan 1
• Pwg +5v 1
• Pwg +5v poti 2
• Quantity control valve
• Sensor ground
• Signal, maf
• Sports exhaust
• Starter relay
• Starting/charging system
• Tailgate sw
• Tank leakage
• Tank leakage diagnostics module
• Terminal 15
• Terminal 30
• Terminal 31
• Terminal 87
• Water shutoff
• X021
• X593

3.6L, Engine Performance Wiring Diagram (2 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.6L, Engine Performance Wiring Diagram (2 of 4) for Porsche 911 Turbo S 2011:

• (fuel tank, under battery) (w/ electronic fuel pump control unit) fuel pump level sensor
• (left rear of engine compt) gp8
• (left side of support frame) gp3
• (rear of luggage compt) (convertible) electric fuel pump control unit
• (side of expansion tank) cooling water level switch
• Air cleaner flap
• Air conditioning system
• Camshaft sensor cylinder (1-3)
• Camshaft sensor cylinder (4-6)
• Clock sig h-
• Cooling water shutoff valve
• Fan relay
• Fuel level grd
• Fuel level sens
• Gnd
• Heated oxygen sensor catalytic converter bank 1
• Heated oxygen sensor catalytic converter bank 2
• Hot film mass air flow sensor 1
• Instrument cluster
• Knock sensor cylinder (1-3) (engine block)
• Knock sensor cylinder (4-6) (engine block)
• Measuring sig
• Nca
• Oil level sensor (under engine, on oil pan)
• Pedal value sensor (behind accelerator pedal)
• Pump
• Pump +
• Pump -
• Pump current
• Pwm
• Resistor rt
• Sports exhaust system valve
• Tank venting valve (fuel filler neck)
• Temp sens
• Term 15
• Term 31
• Term 87
• U battery h+
• Voltage re+
• X011
• X021
• X023
• X591
• X592

3.6L, Engine Performance Wiring Diagram (3 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.6L, Engine Performance Wiring Diagram (3 of 4) for Porsche 911 Turbo S 2011:

• (relay support 1) (convertible) electric fuel pump relay 1
• (top of engine) camshaft adjustment 1 cylinder (1-3)
• (top of engine) camshaft adjustment 2 cylinder (4-6)
• Air bag control unit (below center console)
• Air cleaner
• Camshaft sens 1
• Camshaft sens 2
• Crash input
• Crash output
• Cylinder 2-
• Cylinder 3
• Cylinder 4
• Cylinder 5
• Cylinder 5-
• Dme control unit (left front of engine compt)
• Engine speed +
• Engine speed -
• Fuse f1 25a
• Fuses holder d
• Generator
• Gnd
• Hot at all times
• Lift valve control 1 cylinder (1-3)
• Lift valve control 2 cylinder (4-6)
• Nca
• Oil pressure
• Oil pressure regulator valve
• Resonance flap valve
• Shield
• Speed sensor
• System starting/charging
• Throttle valve
• X591
• X592
• X593

3.6L, Engine Performance Wiring Diagram (4 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.6L, Engine Performance Wiring Diagram (4 of 4) for Porsche 911 Turbo S 2011:

• (intake manifold) throttle valve
• (right side of engine) oil pressure sensor w/ temperature
• (top of cylinders)
• (top of cylinders) fuel injectors
• +5v
• Camshaft adjuster b1
• Camshaft b2
• Control valve
• Cooling water
• Cylinder 1
• Cylinder 2
• Cylinder 6
• Dme control unit (left front of engine compt)
• Electronic mufflers system
• Engine compt
• Exhaust system
• Gp9 (right rear of engine compt)
• Ground, sensors
• High pressure sens
• Ignition coil cylinder
• Injector, cylinder 1+
• Injector, cylinder 1-
• Injector, cylinder 2+
• Injector, cylinder 3+
• Injector, cylinder 3-
• Injector, cylinder 4+
• Injector, cylinder 4-
• Injector, cylinder 5+
• Injector, cylinder 6+
• Injector, cylinder 6-
• Knock sensor 1
• Knock sensor 2
• Nca
• Ntc
• Ntc coolant sensor
• Ntc engine compartment temperature sensor (middle of engine)
• Oil pressure sens
• Oil temp sens
• P-out
• Plug spark
• Rail pressure sensor
• Resonance flap
• Sensor gnd
• Shield
• Sig
• Spark plug
• Tank valve
• Terminal 31
• Throttle valve
• Valve control b1
• Valve control b2
• X591
• X592
• X593

3.8L

3.8L, Engine Performance Wiring Diagram (1 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.8L, Engine Performance Wiring Diagram (1 of 4) for Porsche 911 Turbo S 2011:

• (hfm1)
• (info not available)
• (left kick panel) relay support 1
• +5v vehicle
• A lock starter
• A/t
• Behind oxygen sensor catalytic converter bank 1
• Behind oxygen sensor catalytic converter bank 2
• Blower stage 2
• Bridge plug (relay support 1)
• Can high
• Can low 1
• Clutch interlock switch (top of clutch pedal assembly)
• Clutch switch
• Computer data lines system
• Cooling fans system
• Cooling water
• Current distributor (behind right side of dash)
• Dme control unit (left front of engine compt)
• Dme relay
• Dmtl-heating
• Electronic mufflers system
• Fuel pump
• Fuel pump 1
• Fuse f3 7.5a
• Fuse f4 20a
• Fuse f5 25a
• Fuse f6 25a
• Fuse f7 15a
• Fuse f7 80a
• Fuse f8 7.5a
• Fuses holder d
• Gnd
• Gp4 (center of support frame)
• Gp9 (right rear of engine compt)
• Ground
• Heated oxygen 1
• Heated oxygen 2
• Hot at all times
• Lsf heater nk
• Lsf heater nk b2
• Lsf sig
• Lsf signal nk b1
• Lsu comp
• Lsu ground vk b1
• Lsu heater
• Lsu pumping
• M/t
• Pas control unit
• Pdk control unit
• Pedal sens
• Purge fan 1
• Pwg +5v 1
• Pwg +5v poti 2
• Quantity control valve
• Sensor ground
• Signal, maf
• Sports exhaust
• Starter relay
• Starting/charging system
• Tailgate sw
• Tank leakage
• Tank leakage diagnostics module
• Terminal 15
• Terminal 30
• Terminal 31
• Terminal 87
• Water shutoff
• X021
• X593

3.8L, Engine Performance Wiring Diagram (2 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.8L, Engine Performance Wiring Diagram (2 of 4) for Porsche 911 Turbo S 2011:

• (fuel tank, under battery) (w/ electronic fuel pump control unit) fuel pump level sensor
• (left rear of engine compt) gp8
• (left side of support frame) gp3
• (rear of luggage compt) (convertible) electric fuel pump control unit
• (side of expansion tank) cooling water level switch
• Air cleaner flap
• Air conditioning system
• Camshaft sensor cylinder (1-3)
• Camshaft sensor cylinder (4-6)
• Clock sig h-
• Cooling water shutoff valve
• Fan relay
• Fuel level grd
• Fuel level sens
• Gnd
• Heated oxygen sensor catalytic converter bank 1
• Heated oxygen sensor catalytic converter bank 2
• Hot film mass air flow sensor 1
• Instrument cluster
• Knock sensor cylinder (1-3) (engine block)
• Knock sensor cylinder (4-6) (engine block)
• Measuring sig
• Nca
• Oil level sensor (under engine, on oil pan)
• Pedal value sensor (behind accelerator pedal)
• Pump
• Pump +
• Pump -
• Pump current
• Pwm
• Resistor rt
• Sports exhaust system valve
• Tank venting valve (fuel filler neck)
• Temp sens
• Term 15
• Term 31
• Term 87
• U battery h+
• Voltage re+
• X011
• X021
• X023
• X591
• X592

3.8L, Engine Performance Wiring Diagram (3 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.8L, Engine Performance Wiring Diagram (3 of 4) for Porsche 911 Turbo S 2011:

• (relay support 1) (convertible) electric fuel pump relay 1
• (top of engine) camshaft adjustment 1 cylinder (1-3)
• (top of engine) camshaft adjustment 2 cylinder (4-6)
• Air bag control unit (below center console)
• Air cleaner
• Camshaft sens 1
• Camshaft sens 2
• Crash input
• Crash output
• Cylinder 2-
• Cylinder 3
• Cylinder 4
• Cylinder 5
• Cylinder 5-
• Dme control unit (left front of engine compt)
• Engine speed +
• Engine speed -
• Fuse f1 25a
• Fuses holder d
• Generator
• Gnd
• Hot at all times
• Lift valve control 1 cylinder (1-3)
• Lift valve control 2 cylinder (4-6)
• Nca
• Oil pressure
• Oil pressure regulator valve
• Resonance flap valve
• Shield
• Speed sensor
• System starting/charging
• Throttle valve
• X591
• X592
• X593

3.8L, Engine Performance Wiring Diagram (4 of 4) for Porsche 911 Turbo S 2011

List of elements for 3.8L, Engine Performance Wiring Diagram (4 of 4) for Porsche 911 Turbo S 2011:

• (intake manifold) throttle valve
• (right side of engine) oil pressure sensor w/ temperature
• (top of cylinders)
• (top of cylinders) fuel injectors
• +5v
• Camshaft adjuster b1
• Camshaft b2
• Control valve
• Cooling water
• Cylinder 1
• Cylinder 2
• Cylinder 6
• Dme control unit (left front of engine compt)
• Electronic mufflers system
• Engine compt
• Exhaust system
• Gp9 (right rear of engine compt)
• Ground, sensors
• High pressure sens
• Ignition coil cylinder
• Injector, cylinder 1+
• Injector, cylinder 1-
• Injector, cylinder 2+
• Injector, cylinder 3+
• Injector, cylinder 3-
• Injector, cylinder 4+
• Injector, cylinder 4-
• Injector, cylinder 5+
• Injector, cylinder 6+
• Injector, cylinder 6-
• Knock sensor 1
• Knock sensor 2
• Nca
• Ntc
• Ntc coolant sensor
• Ntc engine compartment temperature sensor (middle of engine)
• Oil pressure sens
• Oil temp sens
• P-out
• Plug spark
• Rail pressure sensor
• Resonance flap
• Sensor gnd
• Shield
• Sig
• Spark plug
• Tank valve
• Terminal 31
• Throttle valve
• Valve control b1
• Valve control b2
• X591
• X592
• X593

3.8L TWIN TURBO

3.8L Twin Turbo, Engine Performance Wiring Diagram (1 of 5) for Porsche 911 Turbo S 2011

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (1 of 5) for Porsche 911 Turbo S 2011:

• (info not available)
• (left kick panel) relay support 1
• A lock
• A/t
• Air pump
• Behind catalytic converter bank 1
• Behind catalytic converter bank 2
• Blower stage 2
• Bridge plug (relay support 1)
• Can high
• Can low 1
• Clutch interlock switch (top of clutch pedal assembly)
• Clutch switch
• Computer data lines system
• Coolant pump
• Cooling fans system
• Cooling water
• Current distributor (behind right side of dash)
• Dme control unit (left front of engine compt)
• Dme relay
• Dmtl-heating
• Fuel pump
• Fuel pump 1
• Fuel pump2
• Fuse f3 7.5a
• Fuse f4 20a
• Fuse f5 25a
• Fuse f6 25a
• Fuse f7 15a
• Fuse f7 80a
• Fuse f8 7.5a
• Fuses holder d
• Gnd
• Gp4 (center of support frame)
• Gp9 (right rear of engine compt)
• Ground
• Heated oxygen 1
• Heated oxygen 2
• Hot at all times
• Lsf heater nk
• Lsf heater nk b2
• Lsf sig
• Lsf signal nk b1
• Lsu comp
• Lsu ground vk b1
• Lsu heater
• Lsu pumping
• M/t
• Maxi fuse 40a
• Pdk control unit (near base of left "b" pillar)
• Pedal sens
• Purge fan 1
• Pwg +5v 1
• Pwg +5v poti 2
• Quantity control valve
• Rear fuse holder
• Red
• Secondary air pump (engine, next to intake bride)
• Secondary air pump relay (relay support 2)
• Sensor gnd
• Starter
• Starter relay
• Starting/charging system
• Tailgate sw
• Tank leakage
• Tank leakage diagnostics module
• Terminal 15
• Terminal 30
• Terminal 31
• Terminal 87
• Water shutoff
• X021
• X023
• X024
• X593

3.8L Twin Turbo, Engine Performance Wiring Diagram (2 of 5) for Porsche 911 Turbo S 2011

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (2 of 5) for Porsche 911 Turbo S 2011:

• (fuel tank, under battery) fuel pump level sensor
• (left rear of engine compt) gp8
• (left side of support frame) gp3
• (rear of luggage compt) electric fuel pump control unit
• (side of expansion tank) cooling water level switch
• Bank 1
• Bank 2
• Camshaft sensor 1 cylinder (1-3)
• Camshaft sensor 2 cylinder (4-6)
• Clock sig h-
• Computer data lines system
• Cooling fans system
• Cooling water shutoff valve
• Electrical water pump
• Exhaust temperature sensor (coupe)
• Fan relay
• Gnd
• Ground
• Heated oxygen sensor catalytic converter bank 1
• Heated oxygen sensor catalytic converter bank 2
• High
• Instrument cluster
• Knock sensor 1 cylinder (1-3) (engine block)
• Knock sensor 1 cylinder (4-6) (engine block)
• Level grd
• Level sens
• Low
• Nca
• Oil level sensor (under engine, on oil pan)
• Pedal value sensor (behind accelerator pedal)
• Pump
• Pump +
• Pump -
• Pump current
• Pwm
• Resistor rt
• Suply
• Tank vent valve (fuel filler neck)
• Term 15
• Terminal 31
• Terminal 87
• U battery h+
• Voltage re+
• X011
• X021
• X023
• X592
• X593

3.8L Twin Turbo, Engine Performance Wiring Diagram (3 of 5) for Porsche 911 Turbo S 2011

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (3 of 5) for Porsche 911 Turbo S 2011:

• (relay support 1) fuel pump relay 1
• (right rear of engine compt) gp9
• (top of engine) camshaft adjustment 1 cylinder (1-3)
• (top of engine) camshaft adjustment 2 cylinder (4-6)
• Actuation
• Air bag control unit (below center console)
• Bank 1
• Bank 2
• Camshaft sens 1
• Camshaft sens 2
• Charge air pressure positioner 2
• Crash input
• Crash out
• Cylinder 2
• Cylinder 3
• Cylinder 4
• Cylinder 5
• Cylinder 5-
• Diverter valve
• Dme control unit (left front of engine compt)
• Engine sens 2
• Engine speed +
• Engine speed -
• Engine speed sensor (clutch bell housing)
• Exhaust temperature sensor
• Fuse f1 25a
• Fuses holder d
• Generator
• Gnd
• Gnd eng sens 3
• Ground
• Hot at all times
• Lift valve control 1 cylinder (1-3)
• Lift valve control 2 cylinder (4-6)
• Nca
• Oil pressure
• Oil pressure regulation valve
• Position
• Positioner 2
• Shield
• System starting/charging
• Throttle valve
• X23
• X591
• X592
• X593

3.8L Twin Turbo, Engine Performance Wiring Diagram (4 of 5) for Porsche 911 Turbo S 2011

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (4 of 5) for Porsche 911 Turbo S 2011:

• (relay support 1) fuel pump relay 2
• Actuation
• Bridge plug (relay support 1)
• Charge air pressure positioner 1
• Computer data lines system
• Drive high
• Drive low
• Fuse f2 25a
• Fuse f6 15a
• Fuse f9 25a
• Fuses holder a
• Fuses holder c
• Fuses holder d
• Gnd sens
• Gnd sens 1
• Gnd sens 2
• Gp9 (right rear of engine compt)
• Ground
• Hot at all times
• Hot w/ term 15 relay energized
• Intake air pressure/ temperature sensor
• Left mount unit
• Left valve +
• Left valve -
• Mounts control unit
• Nca
• Ntc
• Position
• Pressure sig
• Red
• Right mount unit
• Right valve +
• Right valve -
• Sensor +
• Sig
• Signal
• Signal sens 1
• Signal sens 2
• Sply sens 1
• Sply sens 2
• Term 15
• Term 30
• Term 31
• Valve +
• Valve -
• X024
• X593

3.8L Twin Turbo, Engine Performance Wiring Diagram (5 of 5) for Porsche 911 Turbo S 2011

List of elements for 3.8L Twin Turbo, Engine Performance Wiring Diagram (5 of 5) for Porsche 911 Turbo S 2011:

• (intake manifold) throttle valve
• (right side of engine) (w/ temperature sensor) oil pressure sensor
• (top of cylinders)
• (top of cylinders) fuel injectors
• +5v
• Bank 1
• Camshaft adjuster b1
• Camshaft b2
• Charge air pressure
• Charge air pressure/ temperature sensor
• Charge air temp
• Control valve
• Cooling water
• Cylinder 1
• Cylinder 2
• Cylinder 6
• Dme control unit (left front of engine compt)
• Engine compt
• Gp9 (right rear of engine compt)
• Ground, sensors
• High pressure sens
• Ignition coil cylinder
• Injector, cylinder 1+
• Injector, cylinder 1-
• Injector, cylinder 2+
• Injector, cylinder 3+
• Injector, cylinder 3-
• Injector, cylinder 4+
• Injector, cylinder 4-
• Injector, cylinder 5+
• Injector, cylinder 6+
• Injector, cylinder 6-
• Knock sensor 1
• Knock sensor 2
• Nca
• Ntc
• Ntc coolant temperature sensor (engine)
• Ntc engine compartment temperature sensor (middle of engine)
• Oil pressure sens
• Oil temp sens
• P-out
• Plug spark
• Positioner 1
• Pressure sensor
• Pressure sig
• Pressure signal
• Rail pressure sensor
• Resonance flap
• Sensor gnd
• Shield
• Sig
• Spark plug
• Tank valve
• Term 31
• Term. 31
• Throttle valve
• Valve control b1
• Valve control b2
• X591
• X592
• X593