AIR CONDITIONING
Heater Wiring Diagram for Isuzu Rodeo S 2003
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for Heater Wiring Diagram for Isuzu Rodeo S 2003:
- B7 (below center console)
- Blower motor (below right side of dash)
- Blower resistor
- C36/p6 (at right side of engine compt, behind battery)
- Cb 15 elec ig fuse 15a
- Dash fuse box (behind left side of dash, behind panel)
- Eb 16 main fuse 100a
- Eb 5 blower fuse 15a
- Eb 6 blower fuse 15a
- Fan control switch
- Fuse/relay box (on right side of engine compartment)
- Heater a/c control panel
- Heater-a/c relay
- Hot at all times
- Hot in on
- Illumination
- Interior lights system
- J/c a
- Off
- Red
- Thermo fuse
2.2L
2.2L, Manual A/C Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003
List of elements for 2.2L, Manual A/C Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003:
- (at right side of engine compartment, behind battery) c36/p6
- A/c switch
- Air selector knob
- Air source selector lever
- B7 (below center console)
- Bi-level
- Blower motor (below right side of dash)
- Blower resistor
- Defrost
- Diode
- Electronic thermostat (behind glove box, on plenum)
- Evaporator temperature sensor
- Face
- Fan control switch
- Foot
- Foot/ defrost
- Fresh
- Heater a/c control panel
- Illumination
- Intake actuator (on heater case)
- Intake actuator relay (behind glove box)
- Interior lights system
- Nca
- Off
- Recirc
- Red
- Solid state
- Thermo fuse
2.2L, Manual A/C Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003
List of elements for 2.2L, Manual A/C Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003:
- (at right side of engine compartment, behind battery) c36/p6
- (behind left side of radiator grille)
- A/c comp relay ctrl
- A/c compressor
- A/c compressor relay
- A/c on input
- A/c pressure sw input
- A/c pressure switch
- B14
- Braided wire
- C-1
- C-2
- C-3
- C12
- C13
- Cb 15 elec. ig fuse 15a
- Clutch
- Condenser fan (behind right side of radiator grille)
- Condenser fan hi relay
- Condenser fan hi relay ctrl
- Condenser fan lo relay
- Condenser fan lo relay ctrl
- Condenser fan output
- Dash fuse box (behind left side of dash, behind panel)
- E15
- Eb 16 main fuse 100a
- Eb 20 elect fan fuse 40a
- Eb 5 blower fuse 15a
- Eb 6 blower fuse 15a
- Eb 7 a/c fuse 10a
- Ect sens ground
- Engine control module (ecm) or powertrain control module (pcm) (below center of dash)
- Engine controls system
- Engine coolant temperature (ect) sensor (on rear of engine below intake manifold)
- Fuse/relay box (on right side of engine compartment)
- Ground
- Heater- a/c relay
- Hot at all times
- Hot in on
- J/c 37
- J/c a
- Option box (at right side of engine compartment)
- Red
- Reference
- Sens ground
- Thermo switch relay
3.2L
3.2L, Manual A/C Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003
List of elements for 3.2L, Manual A/C Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003:
- (at right side of engine compartment, behind battery) c36/p6
- A/c switch
- A/t
- Air selector knob
- Air source selector lever
- B7 (below center console)
- Bi-level
- Blower motor (below right side of dash)
- Blower resistor
- Defrost
- Diode
- Eb 20 (cond fan) fuse 30a
- Electronic thermostat (behind glove box, on plenum)
- Evaporator temperature sensor
- Face
- Fan control switch
- Foot
- Foot/ defrost
- Fresh
- Fuse/relay box (on right side of engine compartment)
- Heater a/c control panel
- Hot at all times
- Illumination
- Intake actuator (on heater case)
- Intake actuator relay (behind glove box)
- Interior lights system
- Nca
- Off
- Recirc
- Red
- Solid state
- Thermo fuse
3.2L, Manual A/C Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003
List of elements for 3.2L, Manual A/C Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003:
- (at right side of engine compartment, behind battery) p6/c36
- (left rear of engine compartment)
- A/c compressor
- A/c compressor relay
- A/c compressor relay ctrl
- A/c dual pressure switch (behind left side of radiator grille)
- A/c on input
- A/c triple pressure switch (a/t) (behind left side of radiator grille)
- A/t
- C36/p6 (at right side of engine compartment, behind battery)
- Cb 15 elec ig fuse 15a
- Clutch
- Condenser fan (a/t) (behind right side of radiator grille)
- Condenser fan relay (a/t)
- Dash fuse box (behind left side of dash, behind panel)
- E-21
- Eb 16 main fuse 100a
- Eb 5 blower fuse 15a
- Eb 6 blower fuse 15a
- Eb 7 a/c fuse 10a
- Ect input
- Engine control module (ecm)
- Engine controls system
- Engine coolant temperature (ect) sensor (on right front of engine)
- Fuse/relay box (on right side of engine compartment)
- Fuse/relay box (on right side of engine compartment)
- Heater- a/c relay
- Hot at all times
- Hot in on
- J/c a
- M/t
- Red
- Sens ground
- Thermo switch relay
ANTI-LOCK BRAKES
Anti-lock Brakes Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Anti-lock Brakes Wiring Diagram for Isuzu Rodeo S 2003:
- 4wd engaged input
- 4wd engaged output
- Abs ind light ctrl
- Abs indicator light
- B-42
- Battery
- Braided
- Brake fluid level in
- Brake fluid level switch (on left rear of engine compt, in brake fluid reservoir)
- Brake input
- Brake switch (behind left side of dash, on brake pedal support)
- C-16 (left rear corner of engine compt, on inner fender panel)
- C-36/p-6 (right side of engine compt, behind battery)
- C-4
- C-5
- Class 2 serial data
- Dash fuse box (behind left side of dash, behind panel)
- Data link connector (dlc) (below left side of dash, near engine hood release lever)
- Dlc output
- Electronic brake control module (ebcm) (on right rear corner of engine compt)
- Fuse cb-11 meter 15a
- Fuse cb-6 stop light 15a
- Fuse eb-18 abs 50a
- Fuse/relay box (on right side of engine compartment)
- Ground
- Hot at all times
- Hot in on or start
- I-1
- Ignition
- Instrument cluster system
- Left front speed sensor (on inside of front knuckle spindle)
- Lf speed sens input
- Meter assembly
- Rear spd sens input
- Rear speed sensor (beneath rear of vehicle, on top of differential)
- Red
- Rf speed sens input
- Right front speed sensor (on inside of front knuckle spindle)
- Transfer control unit (under center console)
ANTI-THEFT
Forced Entry Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003
List of elements for Forced Entry Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003:
- (below center console) b7
- Act pos locked
- Act pos unlocked
- Anti- theft fuse 23 10a
- Anti-theft horn (on right rear corner of engine compartment)
- Anti-theft indicator light
- B7 (below center console)
- Battery input
- C36/p6 (at right side of engine compt, behind battery)
- Ceiling light trigger
- Dash fuse box (behind left side of dash, behind panel)
- Diode box 5
- Diode box 6
- Disarm lock input
- Disarm unlock input
- Door locks system
- Door/hatch open in
- Dr door act ctrl
- Engine hood input
- Engine hood switch (at right rear corner of engine compt)
- Exterior lights system
- Fuse/relay box (on right side of engine compartment)
- Ground
- Hatch gate open switch (inside top center of tailgate, on latch assembly)
- Headlight rly ctrl
- Headlights systems
- Horn fuse 2 10a
- Hot at all times
- Hot in acc or on
- Ignition input
- Ignition switch
- Interior lights system
- J/c b
- Key in ignition
- Key reminder switch
- Key rod act posit
- Keyless entry & anti-theft control unit (behind right side of dash, above kick panel)
- Left front door switch
- Left rear door switch (rodeo)
- Lock input
- Lock/unlock input
- Power door lock fuse 7 20a
- Red
- Right front door switch
- Right rear door switch (rodeo)
- Rodeo
- Rodeo sport
- Security horn ctrl
- Security ind ctrl
- Switch unit a
- Tailgate open switch (on tailgate)
- Taillight relay
- Unlock input
- Warning system
- Wiper/ washer system
Forced Entry Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003
List of elements for Forced Entry Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003:
- (below center console) b7
- (momentary)
- Driver's door key detect & actuator position switches
- Left front door key detect switch
- Left front door lock actuator
- Left rear door actuator position switch
- Left rear door lock actuator
- Lock
- Right front door actuator position switch
- Right front door key detect switch
- Right front door lock actuator
- Right rear door actuator position switch
- Right rear door lock actuator
- Rodeo
- Tailgate actuator position switch
- Tailgate door lock actuator (rodeo: at lower right side of tailgate) (rodeo sport: at center of tailgate)
- Tailgate key detect switch
- Unlock
Immobilizer Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Immobilizer Wiring Diagram for Isuzu Rodeo S 2003:
- (+)
- (-)
- (at right side of intake manifold) e30
- (below center of dash) immobilizer control unit
- (left rear of engine compt) engine control module (ecm)
- Battery input
- Dash fuse box (behind left side of dash, behind panel)
- Data link connector (below left side of dash, near engine hood release)
- E-22
- Ecm output
- Engine fuse 12 15a
- Fuse/relay box (on right side of engine compartment)
- Ground
- Hot at all times
- Hot in on or start
- I-55
- I-9
- I-99
- Ignition input
- Immobi- lizer ind lamp
- Immobilizer antenna coil (in right side of steering column, around ignition lock cylinder)
- Immobilizer fuse 4 10a
- Ind control
- Meter assembly
- Meter fuse 11 15a
- Nca
- Starter relay
- Vehicle speed sensor (beneath center of vehicle, rear of transmission)
- Vss input
BODY CONTROL MODULES
Body Control Modules Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Body Control Modules Wiring Diagram for Isuzu Rodeo S 2003:
- (rodeo)
- 3.2l a/t
- 3.2l m/t
- A/t (p) (or m/t) shift ind
- A/t shift indicator (2)
- A/t shift indicator (3)
- A/t shift indicator (d)
- A/t shift indicator (l)
- A/t shift indicator (n)
- A/t shift indicator (r)
- A/t shift indicator power
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- Anti-theft system
- B7 (below center console)
- Battery power
- Beeper
- Check trans indicator
- Computer data lines system
- Dash fuse box (behind left side of dash, behind panel)
- Driver's door open in
- Ecm/pcm communication
- Engine controls system
- Exterior lights system
- Exterior, interior lights systems
- Fuse cb-11 meter 15a
- Fuse cb-16 rear wiper & washer 10a
- Fuse cb-17 front wiper & washer 20a
- Fuse cb-5 dome light 10a
- Fuse cb-7 power door lock 20a
- Fuse eb-2 horn 10a
- Fuse/ relay box (on right side of engine compt)
- Ground
- Ground or up shift input
- Hatch open input
- Horn output
- Horn relay control
- Horns system
- Hot at all times
- Hot in on
- Hot in on or start
- I41
- I42
- Ignition input
- Ignition power
- Key in ignition input
- Key reminder switch
- Left front door switch
- Lights on input
- Low fuel indicator
- Multiplexed indicator control unit (2.2l) (below rear of center console)
- Off input
- Pnk
- Power drive indicator
- Rear washer control
- Rear washer on input
- Rear wiper motor control
- Rear wiper motor ctrl
- Rear wiper motor ctrl shift ind(1) (or up shift ctrl)
- Rear wiper on input
- Red
- Seat belt unbuckled input
- Starter switch
- Transmissions system
- W/ anti- theft
- W/o anti- theft
- Warning system
- Washer input
- Winter drive indicator
- Wiper intermittent input
- Wiper run/park input
- Wiper variable intermittent
- Wiper/ washer system
- Wiper/washer system
COMPUTER DATA LINES
2.2L
2.2L, Computer Data Lines Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 2.2L, Computer Data Lines Wiring Diagram for Isuzu Rodeo S 2003:
- (at right rear of engine) e28
- B26
- B6 c4
- C1 b13
- C36/p6 (at right side of engine compt, behind battery)
- D4 c2
- Data link connector (below left side of dash, near engine hood release)
- Electronic brake control module (on right rear corner of engine compt)
- Engine control module (ecm) or powertrain control module (pcm) (below center of dash)
- Fuse 2 horn 10a
- Fuse/ relay box (on right side of engine compt)
- Hot at all times
- I-30
- Multiplexed indicator control unit (below rear of center console)
- Red
- Sensing & diagnostic module (below center of dash)
3.2L
3.2L, Computer Data Lines Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 3.2L, Computer Data Lines Wiring Diagram for Isuzu Rodeo S 2003:
- (at right side of engine compt, behind battery) c36/p6
- (left rear of engine engine compt)
- C4 b6
- C52
- C78
- C79
- Data link connector (below left side of dash, near engine hood release)
- E21
- E22
- E30 (at right side of intake manifold)
- Electronic brake control module (on right rear corner of engine compt)
- Engine control module (ecm)
- Fuse 2 horn 10a
- Fuse/ relay box (on right side of engine compt)
- Hot at all times
- I30
- I55
- Immobilizer control unit (below center of dash)
- Intelligent suspension control unit (below center of dash)
- Red
- Sensing & diagnostic module (below center of dash)
- Transmission control module (under left side of dash)
CRUISE CONTROL
3.2L
3.2L, Cruise Control Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 3.2L, Cruise Control Wiring Diagram for Isuzu Rodeo S 2003:
- (below center of dash) immobilizer control unit
- (left rear of engine compt)
- Acceleration position sensor assembly (above accelerator pedal)
- Acceleration sensors
- Ap sen1 gnd
- Ap sen2 gnd
- Ap sensor 1
- Ap sensor 2
- Ap sensor 3
- Aps3 gnd
- B-19
- Brake sw in
- Brake switch (behind left side of dash, on brake pedal support)
- C-52
- C16 (at left rear corner of engine compt, on inner fender panel)
- Cancel
- Cancel in
- Cb-11 meter fuse 15a
- Cb-12 engine ig fuse 15a
- Cb-14 back-up/ turn light fuse 15a
- Cb-6 stop light fuse 15a
- Clutch switch (m/t) (behind left side of dash, on clutch pedal support)
- Cruise brake
- Cruise control main switch
- Cruise control switch
- Cruise lmp
- Cruise set light
- Cruise sw
- Dash fuse box (behind left side of dash, behind panel)
- Drive input
- E-21
- E-22
- E28 (at left side of intake manifold)
- E30 (at right side of intake manifold)
- Eb-17 ecm fuse 30a
- Ecm or pcm main relay
- Engine control module (ecm) or powertrain control module (pcm)
- Fuse/relay box (on right side of engine compt)
- Gnd
- Hot at all times
- Hot in on or start
- I-2
- I-55
- I-9
- Ign
- Ign feed
- Illumination
- Ind on/off cruise
- Intelligent suspension control unit (below center of dash)
- Interior lights system
- Meter assembly
- Nca
- On switch
- Pnk
- Red
- Ref volt
- Res/acc
- Set/cst
- Solid state sensor
- Speedometer
- Srs coil assembly
- Steering wheel
- Switch unit a
- Th val mtr+
- Throttle position sensor 1
- Throttle position sensor 2
- Throttle val-
- Throttle valve assembly
- Throttle valve motor
- Tps 1 sign
- Tps1 gnd
- Tps2 gnd
- Tps2 sign
- Transfer control unit (below center console)
- Vehicle speed sensor (beneath center of vehicle, rear of transmission)
- Vss in
DEFOGGERS
Defoggers Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Defoggers Wiring Diagram for Isuzu Rodeo S 2003:
- 2.2l
- 3.2l
- A14
- B7 (below center console)
- C-1
- C-3
- Dash fuse box (behind left side of dash, behind panel)
- Defogger
- Defogger relay control e-22
- Defogger request input e-22
- E12
- Engine control module (ecm) or powertrain control module (pcm) (2.2l: below center of dash) (3.2l: left rear of engine compt)
- Fuse cb-10 rear defogger 15a
- Fuse cb-16 rear wiper & washer 10a
- Fuse cb-8 mirror defogger 10a
- Fuse cb-9 rear defogger 15a
- Fuse eb-16 main 100a
- Fuse/relay box (on right side of engine compartment)
- G-12
- G-9
- Hot at all times
- Hot in on
- Interior lights system
- Left power mirror
- Mirror control switch
- Mirror defogger switch
- Momentary on
- On ind
- On indicator
- Rear defogger
- Rear defogger switch
- Rear window defogger relay
- Rear window defogger switch light
- Right power mirror
- Switch unit b
- W/ rear defogger
- W/o rear defogger
ELECTRONIC SUSPENSION
Electronic Suspension Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Electronic Suspension Wiring Diagram for Isuzu Rodeo S 2003:
- (at left rear corner of engine compartment, on inner fender panel) c16
- (below left side of dash, near engine hood release) data link
- (left rear of engine
- 30a
- Actuator g-sensor
- Brake switch (behind left side of dash, on brake pedal support)
- C36 (at right side of engine compartment, behind battery)
- C50
- C51
- C52
- Cb-11 meter fuse 15a
- Cb-14 back up/ turn light fuse 15a
- Cb-6 stop light fuse 15a
- Center of vehicle, rear of transmission)
- Compt)
- Connector
- Cruise control system
- Dash fuse box (behind left side of dash, behind panel)
- E-21
- Engine control module (ecm)
- G-sensor (g-3) (inside of frame, forward of left rear wheel)
- Hot at all times
- Hot in on or start
- I-1
- I-9
- Illumination
- Instrument cluster system
- Intelligent suspension control unit (below center of dash)
- Intelligent suspension mode switch
- Intelligent suspension warning system light
- Interior lights system
- Left front actuator assembly
- Left rear actuator assembly
- Meter assembly
- Off
- Option box (at right side of engine compt)
- Pnk
- Red
- Right front actuator assembly
- Right rear actuator assembly
- Sport mode indicator light
- Vehicle speed sensor (beneath
- Vertical g-sensor
ENGINE PERFORMANCE
2.2L
2.2L, Engine Performance Wiring Diagram (1 of 3) for Isuzu Rodeo S 2003
List of elements for 2.2L, Engine Performance Wiring Diagram (1 of 3) for Isuzu Rodeo S 2003:
- (below
- (on throttle body)
- (on throttle body) idle air control valve
- (right rear of engine) e-28
- (right side of engine block)
- (right side of engine)
- 5v ref a
- 5v ref b
- A/c system
- A10
- A11
- A12
- A13
- A14
- A15
- A16
- B10
- B11
- B12
- B13
- B14
- B15
- B16
- Braid
- C-36 (near battery)
- C-37
- C-37 (below center of dash)
- C10
- C11
- C12
- C13
- C14
- C15
- C16
- Center console) b-7
- Center of dash)
- Ckp sens hi
- Ckp sens in
- Class 2 data
- Comp relay
- Cond fan
- Crankshaft position sensor (lower left front of engine)
- Cut vlv ctrl
- Defog ctrl
- Defogger system
- E-28 (right rear of engine)
- Ecm fuse 15a
- Ect output
- Egr
- Engine coolant temperature sensor (in coolant manifold)
- Engine or powertrain control module (below center of dash)
- Evap
- Fuel lev in
- Fuel lev out
- Fuel pump
- Fuel pump fuse 20a
- Fuel tank sender
- Fuel vapor pressure sensor (top of fuel tank)
- Fuse/ relay box (right side of engine compt)
- Ground
- Heated oxygen sensor (ho2s-post) (rear of converter)
- Heated oxygen sensor (ho2s-pre) (in exhaust downpipe)
- Ho2s in
- Hot at all times
- Iac a hi
- Iac a lo
- Iac b hi
- Iac b lo
- Iat
- Icm ctrl
- Inj 2
- Instrument cluster system
- Knock sensor
- Manifold absolute pressure sensor
- Mil ind
- O2 sens heater fuse 10a
- Power steering pressure switch (on power steering pump)
- Press sw
- Psp
- Red
- Shift sol b
- Tachometer
- Tan
- Throttle position sensor
- Twisted pair
- Vapor press
2.2L, Engine Performance Wiring Diagram (2 of 3) for Isuzu Rodeo S 2003
List of elements for 2.2L, Engine Performance Wiring Diagram (2 of 3) for Isuzu Rodeo S 2003:
- (right rear of engine)
- (right side of rear axle) evaporative emission canister cut valve
- B-26
- Braid
- C-16 (left rear of engine compt)
- C-37 (below center of dash)
- Camshaft position sensor (top center
- Dash fuse box (left side of dash)
- Data link connector (below left side of dash)
- E-28 (right rear of engine)
- Electronic brake control module
- Engine ig fuse 15a
- Evaporative emission canister purge valve
- Exhaust gas recirculation solenoid valve (top center rear of engine)
- Front of engine)
- Fuel level
- Fuel pump relay
- Fuse/ relay box
- Hot at all times
- Hot in on or start
- I-1
- I-2
- I-9
- Ig coil fuse 15a
- Ign b1 fuse 60a
- Ignition control module (right rear of engine)
- Intake air temperature sensor (left front of engine compt)
- Malfunction indicator light (mil)
- Meter assembly
- Meter fuse 15a
- Multi- plexed indicator control unit
- Red
- Sensing & diagnostic module
- Tach
- To spark plugs
- Vehicle speed sensor (rear of transmission)
- Vss in
2.2L, Engine Performance Wiring Diagram (3 of 3) for Isuzu Rodeo S 2003
List of elements for 2.2L, Engine Performance Wiring Diagram (3 of 3) for Isuzu Rodeo S 2003:
- (in fuse/relay box) ecm or pcm main relay
- (left rear of transmission) transmission speed sensor
- (left side of transmission) a/t mode switch
- A/c request
- A/c system
- A/t mode sw
- Automatic transmission
- B-7 (below center console)
- Backup/ turn fuse 15a
- Bba sol
- Braid
- Brake sw
- Brake switch (on brake pedal bracket)
- C-36 (near battery)
- Cmp sens in
- Cond fan
- D10
- D11
- D12
- D13
- D14
- D15
- D16
- Dash fuse box (left side of dash)
- Defog req
- Defogger system
- Duty sol
- E-28
- E-28 (right rear of engine)
- E10
- E11
- E12
- E13
- E14
- E15
- E16
- Ecm fuse 15a
- Ects
- Egr vlv ctrl
- Engine or powertrain control module (below center of dash)
- Exterior lights, abs system
- F10
- F11
- F12
- F13
- F14
- F15
- F16
- Fp relay
- Fuel injectors
- Fuse/ relay box (right side of engine compt)
- Ho2s in
- Hot at all times
- Hot in on or start
- Icm ctrl
- Ignition
- Inj 1
- Inj 3
- Inj 4
- Kick down switch (behind left side of dash)
- Kick dwn sw
- M-6
- M-7
- Map
- Pc sol +
- Pc sol -
- Pnk
- Power
- Power sw
- Power/ winter switch (a/t)
- Pressure control solenoid
- Red
- Sens grd
- Sens return
- Shift sol a
- Shift solenoid a
- Shift solenoid b
- Stop fuse 15a
- Switched b+
- Tcc sol
- Tft sens
- Torque converter clutch solenoid
- Tps
- Trans- mission fluid temper- ature sensor
- Tss +
- Tss -
- Vss
- Winter
- Winter sw
3.2L
3.2L, Engine Performance Wiring Diagram (1 of 4) for Isuzu Rodeo S 2003
List of elements for 3.2L, Engine Performance Wiring Diagram (1 of 4) for Isuzu Rodeo S 2003:
- (below center console) b-7
- (on intake manifold)
- (rear of left front fender) c-16
- (right side of intake manifold)
- (top left side of intake manifold)
- (top right side of intake manifold) e-30
- A/c clutch
- A/c req
- A/c system
- Ap sen1 gnd
- Ap sen2 gnd
- B1s1
- B1s2
- B2s1
- B2s2
- Braided wires
- Brake sw in
- C.q. sign in
- Ckp in
- Clutch sw in
- Crankshaft position sensor (lower right side of eng)
- Cruise brake
- Cruise control
- E-21
- E-28
- E-28 (left side)
- E-30
- E-30 (right side)
- Ecm fuse 10a
- Ecm fuse 30a
- Ecm main relay
- Ect in
- Engine coolant temperature sensor (right front of eng)
- Engine or powertrain control module (left side of engine compt)
- Etc gnd
- F13
- F14
- F15
- F16
- F17
- F18
- F19
- F20
- F21
- F22
- F23
- F24
- F25
- F26
- F27
- F28
- F29
- F30
- F31
- F32
- F33
- F34
- F37
- F38
- F39
- F40
- F41
- F42
- F43
- F44
- F45
- F46
- F47
- F48
- F49
- F50
- F51
- F52
- F53
- F54
- F55
- F56
- F57
- F58
- F59
- F60
- F61
- F62
- F63
- F64
- F65
- F66
- F67
- F68
- F69
- F70
- F71
- F72
- F73
- F74
- F75
- F76
- F77
- F78
- F79
- F80
- Fuel injectors
- Fuel pump
- Fuel pump fuse 20a
- Fuel pump relay
- Fuel tank unit (top of fuel tank)
- Fuse/ relay box (right side of engine compt)
- Gnd
- Headlights system
- Ho2s b1s2 -
- Ho2s2 h gnd
- Hot at all times
- Iat in
- Ig coil2 ctrl
- Ig coil3 ctrl
- Ign b1 fuse 60a
- Ign feed
- Ind ctrl
- Knock sig in
- Lights on
- Maf in
- Map in
- N01 fuel inj
- N02 fuel inj
- N03 fuel inj
- N04 fuel inj
- N05 inj ctrl
- O2 sens heater fuse 20a
- Pins not used: f8-f12, f35-f36
- Pnk
- Psp sw in
- Red
- Ref volt
- Res/acc in
- Serial data
- Starter feed
- Starting system
- Tach
- Throttle position sensor 1
- Throttle position sensor 2
- Throttle val
- Throttle valve assembly (on throttle body assembly)
- Throttle valve motor
- Tps1 gnd
- Tps2 gnd
- Tps2 sign
- Vapor sen
3.2L, Engine Performance Wiring Diagram (2 of 4) for Isuzu Rodeo S 2003
List of elements for 3.2L, Engine Performance Wiring Diagram (2 of 4) for Isuzu Rodeo S 2003:
- 1,3,5 coil in
- 2,4,6 coil in
- Back up/ turn light fuse 15a
- Brake switch (on brake pedal support)
- Clutch switch (on clutch pedal support)
- Coil 1 ctrl
- Coil 2 ctrl
- Coil 3 ctrl
- Coil 4 ctrl
- Coil 5 ctrl
- Coil 6 ctrl
- Con- denser (right front of eng)
- Dash fuse box (left side of dash)
- E-16
- E-17
- E-18
- E-29 (top left side of intake manifold)
- Engine ig fuse 15a
- Est 11
- Est 12
- Est 13
- Est 21
- Est 22
- Est 23
- Exterior lights, abs
- Gnd
- Hot at all times
- Hot in on or start
- Ig coil fuse 15a
- Ign
- Ignition coils
- Ion sensing module (top of engine intake plenum)
- Ioncq1
- Ionk1
- Meter fuse 15a
- Pnk
- Power steering pressure switch (on power steering pump)
- Red
- Stop light fuse 15a
3.2L, Engine Performance Wiring Diagram (3 of 4) for Isuzu Rodeo S 2003
List of elements for 3.2L, Engine Performance Wiring Diagram (3 of 4) for Isuzu Rodeo S 2003:
- (above right side of rear axle) evap canister vent valve
- (front of engine) evap canister purge valve
- (in air duct assembly) intake air temperature sensor
- (in air duct assembly) mass air flow sensor
- (top left rear of eng) variable intake manifold vacuum switch valve
- (top left side of intake manifold)
- (top of fuel tank) fuel vapor pressure sensor
- (top rear of intake manifold) manifold absolute pressure sensor
- (top right rear of engine) exhaust gas recirculation solenoid valve
- (top right side of intake manifold)
- Alarm and relay control unit (above right kick panel)
- C-78
- Data link connector (on lower left side of dash)
- E-28
- E-30
- Electronic brake control module (right rear corner of engine compt)
- Est 11
- Est 12
- Est 13
- I-41
- Pnk
- Red
- Serial data
- Transmission control module (under left side of dash)
3.2L, Engine Performance Wiring Diagram (4 of 4) for Isuzu Rodeo S 2003
List of elements for 3.2L, Engine Performance Wiring Diagram (4 of 4) for Isuzu Rodeo S 2003:
- "u/s" ind
- (on accelerator pedal bracket)
- (top left side of intake manifold)
- (top right side of intake manifold)
- A/c system
- Acceleration position sensor assembly
- Acceleration sensors
- Ap sensor 1
- Ap sensor 2
- Ap sensor 3
- Aps3 gnd
- B1s1
- B1s2
- B2s1
- B2s2
- Braid
- Braided wires
- Can +
- Can cut val
- Can-
- Cruise cancel
- Cruise control
- Cruise lmp
- Cruise sw
- Defog req
- Defog rly
- Defogger system
- Defogger system starter system
- Dlc
- E-22
- E-28
- E-28 (top left side of intake manifold)
- E-30
- E-30 (top right side of intake manifold)
- Ect out
- Egr ctrl lo
- Egr in
- Electronic suspension system
- Eng coolant temp gauge
- Engine or powertrain control module (left side of engine compt)
- Evap purge
- Fuel gage
- Fuel gauge
- Fuel sen
- Fuel sender
- Fuel tank sender
- Fuel tank unit (on top of fuel tank)
- Gnd
- Heated oxygen sensor (b1s1) (right exhaust downpipe)
- Heated oxygen sensor (b1s2) (rear of right cat converter)
- Heated oxygen sensor (b2s1) (left exhaust downpipe)
- Heated oxygen sensor (b2s2) (rear of left cat converter)
- Ho2s b1s1 +
- Ho2s b1s1 -
- Ho2s b1s2 +
- Ho2s b2s1 +
- Ho2s b2s1 -
- Ho2s b2s2 +
- Ho2s b2s2 -
- Ho2s1 h gnd
- Ho2s1h gnd
- I-1
- I-2
- I-9
- Iat sen
- Ig coil1 ctrl
- Ig coil4 ctrl
- Ig coil5 ctrl
- Ig coil6 ctrl
- Ign feed
- Immobil in
- Low fuel warning light
- Malfunc- tion indicator light (mil)
- Map
- Meter assembly
- Mil ind ctrl
- No6 fuel inj
- Pnk
- Red
- Reduced power ind
- Ref volt
- S10
- S11
- S12
- S13
- S14
- S15
- S16
- S17
- S18
- S19
- S20
- S21
- S22
- S23
- S24
- S25
- S26
- S27
- S28
- S29
- S30
- S31
- S32
- S33
- S34
- S35
- S36
- S37
- S38
- S39
- S40
- S41
- S42
- S43
- S44
- S45
- S46
- S47
- S48
- S49
- S50
- S51
- S52
- S53
- S54
- S55
- S56
- S57
- S58
- S59
- S60
- S61
- S62
- S63
- S64
- S65
- S66
- S67
- S68
- S69
- S70
- S71
- S72
- S73
- S74
- S75
- S76
- S77
- S78
- S79
- S80
- St relay ctrl
- Tach- ometer
- Th val mtr
- Tps 1 sign
- Trans spd
- Transmission speed sensor (a/t) (top of transmission)
- Up ind in
- Vapor press
- Via vsv ctrl
EXTERIOR LIGHTS
Back-up Lamps Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Back-up Lamps Wiring Diagram for Isuzu Rodeo S 2003:
- (below center console) b7
- (not used)
- 2.2l a/t
- 3.2l a/t
- Automatic transmission mode switch (beneath center of vehicle, on left side of transmission)
- Back-up light
- Back-up light switch (3.2l: beneath vehicle, on top of transmission) (2.2l: beneath vehicle, on left side of transmission)
- Dash fuse box (behind left side of dash, behind panel)
- Fuse 14 back up/ turn light 15a
- Hot in on or start
- Left taillight assembly
- M/t
- Neutral start safety switch (on right front exhaust downpipe)
- Red
- Right taillight assembly
- Rodeo sport
- Transmissions system
Exterior Lamps Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003
List of elements for Exterior Lamps Wiring Diagram (1 of 2) for Isuzu Rodeo S 2003:
- (at left rear corner of engine compt, on inner fender panel) c16
- (below center console) b7
- B7 (below center console)
- Behind trim) (rodeo sport: in right "d"
- Combination switch
- Dash fuse box (behind left side of dash, behind panel)
- Flasher unit (above left kick panel)
- Fuse 1 hazard 15a
- Fuse 14 back up/ turn light 15a
- Fuse/relay box (on right side of engine compartment)
- Gnd
- H-23 (rodeo: in left "d"
- Hazard
- Hazard warning switch
- Hazard warning switch light
- Hot at all times
- Hot in on or start
- I-2
- Ignition
- Interior lights system
- Left
- Left front combination light
- Left turn indicator light
- Meter assembly
- Off
- Output
- Pillar,
- Pillar, behind trim)
- Pnk
- Red
- Right
- Right front combination light
- Right turn indicator light
- Trailer connector
- Turn signal switch
Exterior Lamps Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003
List of elements for Exterior Lamps Wiring Diagram (2 of 2) for Isuzu Rodeo S 2003:
- (below center console) b7
- 3.2l
- Brake switch (behind left side of of dash, on brake pedal support)
- Combination switch
- Dash fuse box (behind left side of dash, behind panel)
- Engine controls system
- Fuse 4 tail/illumi light 15a
- Fuse 6 stop light 15a
- Head
- High mount stop light
- High mounted stop light
- Hot at all times
- Interior lights system
- Keyless entry & anti-theft control unit (behind right side of dash, above kick panel)
- Left license light
- Left taillight assembly
- License light
- Lighting switch
- Off
- Park
- Pnk
- Red
- Red red
- Right license light
- Right taillight assembly
- Rodeo & rodeo sport hard-top
- Rodeo sport soft-top
- Shift interlock system
- Stop
- Tail
- Tail/stop light
- Taillight relay
- Transmissions, anti-lock brakes, cruise control systems
- Turn light
- W/ optional spare tire mounted on rear door
- W/o optional spare tire mounted on rear door
GROUND DISTRIBUTION
Ground Distribution Wiring Diagram (1 of 4) for Isuzu Rodeo S 2003
List of elements for Ground Distribution Wiring Diagram (1 of 4) for Isuzu Rodeo S 2003:
- (2.2l)
- (2.2l) kick down switch
- (2.2l) multi-plexed indicator control unit
- (3.2l)
- (3.2l) condenser fan
- (3.2l) sensing & diagnostic module (sdm)
- (a/t)
- (ebcm)
- (on right side of engine compartment) fuse/relay box
- (w/ amplifier)
- (w/o amplifier)
- 2-4wd switch
- 2.2l
- 2.2l, w/ m/t
- 3.2l
- 3.2l, w/ a/t
- Alarm & relay control unit
- Amplifier
- B-26
- B-41
- B7 (below center console)
- Battery
- Brake fluid level switch
- C-4
- C-5
- C-50
- C16 (at left rear corner of engine compt, on inner fender panel)
- Condenser fan
- Condenser fan relay
- Data link connector (dlc)
- Driver's seat belt switch
- Ecm main relay
- Electronic brake control module
- Engine hood switch
- Front axle motor actuator
- Fuel pump relay
- Heated oxygen sensor (ho2s-post)
- Heated oxygen sensor (ho2s-pre)
- Heater- a/c relay
- I-1
- I-2
- I-30
- I-42
- I43 (below left side of dash, above kick panel)
- Intake actuator relay
- Intelligent suspension control unit
- Left foglight
- Left front combination light
- Meter assembly
- Neutral switch
- P10 (at lower right front of engine)
- P6/c36 (at right side of engine compt, behind battery)
- Power/winter switch
- Radio
- Rear defogger switch
- Rear washer motor
- Right foglight
- Right front combination light
- Starter relay
- Switch unit b
- To b7 (diagram 4 of 4)
- To condenser fan high relay 2 (diagram 3 of 4)
- Transfer actuator
- Vehicle speed sensor (vss)
- Windshield washer motor
- Windshield wiper motor
Ground Distribution Wiring Diagram (2 of 4) for Isuzu Rodeo S 2003
List of elements for Ground Distribution Wiring Diagram (2 of 4) for Isuzu Rodeo S 2003:
- (a/t) transmission control module
- 2-4wd shift actuator
- 3.2l
- 4wd switch
- Acceleration position sensor assembly shield
- C-78
- Crankshaft position (ckp) sensor shield
- Cruise control switch
- Data link connector (dlc)
- E-16
- E-21
- E-22
- E-33
- E28 (at left side of intake manifold)
- E29 (at left side of intake manifold)
- E30 (at right side of intake manifold)
- Engine control
- Engine control module (ecm)
- Exhaust gas recirculation (egr) solenoid valve
- Heated oxygen sensor (bank 1 sensors 1 & 2) shield
- Heated oxygen sensor (bank 2 sensors 1 & 2) shield
- Ignition coils 1, 3, 5 shield
- Ignition coils 2, 4 & 6 shield
- Immobilizer control unit
- Ion sensing module
- M/t
- Mass airflow (maf) sensor
- Mass airflow (maf) sensor shield
- Module (ecm)
- Neutral switch
- Radio remote switch
- Srs coil assembly
- Steering wheel
- Throttle valve assembly assembly shield
- Throttle valve assembly shield
- Transmission speed sensor
- Vehicle speed sensor
Ground Distribution Wiring Diagram (3 of 4) for Isuzu Rodeo S 2003
List of elements for Ground Distribution Wiring Diagram (3 of 4) for Isuzu Rodeo S 2003:
- (on right side of engine compartment) fuse/relay box
- 2.2l
- 2.2l w/ a/t
- Braided wire
- C-2
- Camshaft position (cmp) sensor
- Camshaft position (cmp) sensor shield
- Coil
- Condenser fan high relay 2
- Crankshaft position (ckp) sensor
- Crankshaft position (ckp) sensor shield
- Data link connector (dlc)
- Driver's power seat switch
- E-32
- E-37
- E28 (at right rear of engine)
- Ecm main relay
- Ecm/pcm
- From a condenser fan (diagram 1 of 4)
- Fuel pump relay
- Heated oxygen sensor (ho2s-post) shield
- Heated oxygen sensor (ho2s-pre) shield
- Ignition control module (icm)
- J/c c-37
- Knock sensor (ks) shield
- Knock sensor shield
- Option box (at right side of engine compartment)
- Passenger's power seat switch
- Rodeo except s model
- Throttle position (tp) sensor shield
- To rear window defogger (diagram 4 of 4)
Ground Distribution Wiring Diagram (4 of 4) for Isuzu Rodeo S 2003
List of elements for Ground Distribution Wiring Diagram (4 of 4) for Isuzu Rodeo S 2003:
- (behind left side of dash, behind panel) dash fuse box
- Accessory socket relay
- Ashtray light
- B-42
- B7 (below center console)
- Back up
- Cigarette lighter
- Coil
- Combination switch
- Driver selector switch
- Fan control switch
- Flasher unit
- From b7 (diagram 1 of 4)
- From rear defogger (diagram 3 of 4)
- Front accessory socket
- Fuel tank unit
- G-10
- G-12
- Glove box light
- Hard top rodeo sport
- Hatch gate open switch
- Heater-a/c control unit
- High mounted stoplight
- I-2
- I-21
- I-29
- Illumination controller
- J-1
- Keyless entry & anti-theft control unit
- Left front door key detect & actuator position switches
- Left front door key detect switch
- Left front door lock actuator
- Left front door power window & lock switch
- Left front vanity mirror light
- Left license light
- Left map light
- Left power mirror
- Left rear door actuator position switch
- Left rear door lock actuator
- Left rear power window switch
- Left taillight assembly
- License plate light
- Lse
- Meter assembly
- Mirror control switch
- Power window relay
- Rear defogger
- Rear view mirror
- Rear wiper motor
- Right front door actuator position switch
- Right front door key detect switch
- Right front door lock actuator
- Right front door power window & lock switch
- Right front vanity mirror light
- Right license light
- Right map light
- Right power mirror
- Right rear door actuator position switch
- Right rear door lock actuator
- Right rear power window switch
- Right taillight assembly
- Rodeo
- Rodeo except s model
- Shift lock controller
- Soft top rodeo sport
- Sun roof control unit
- Switch unit a
- Tail/ stop
- Tailgate actuator position switch
- Tailgate door lock actuator
- Tailgate key detect switch
- Trailer harness connector
- Transfer control unit
- Turn
- W/ optional mounted spare tire on rear door
- W/o optional spare tire mounted on rear door
HEADLIGHTS
Headlights Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Headlights Wiring Diagram for Isuzu Rodeo S 2003:
- Anti- theft, door locks systems
- B7 (below center console)
- C16 (at left rear corner of engine compt, on inner fender panel)
- Combination switch
- Dimmer passing switch
- Dimming
- Fog- light switch (3.2l)
- Foglight relay (3.2l)
- Fuse 10 fog light 15a
- Fuse 8 lh h/lamp 10a
- Fuse 9 rh h/lamp 10a
- Fuse/ relay box (on right side of engine compt)
- Head
- Headlight relay
- High beam ind
- Hot at all times
- I-2
- Illum
- Interior lights system
- J/c b
- Left fog- light (3.2l)
- Left headlight
- Lighting switch
- Meter assembly
- Off
- On ind
- Park
- Parking lights
- Passing
- Red
- Right fog- light (3.2l)
- Right headlight
HORN
Horn Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Horn Wiring Diagram for Isuzu Rodeo S 2003:
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- Driver's inflator module
- Fuse 2 horn 10a
- Fuse/relay box (on right side of engine compartment)
- High note horn (behind right side of radiator grille)
- Horn relay
- Horn switch
- Hot at all times
- I42
- Low note horn (behind right side of radiator grille)
- Srs coil assembly
- Steering wheel
INSTRUMENT CLUSTER
2.2L
2.2L, Instrument Cluster Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 2.2L, Instrument Cluster Wiring Diagram for Isuzu Rodeo S 2003:
- (beneath center console, on parking brake lever) parking brake switch
- 4l indicator light
- 4wd indicator light
- Abs indicator light
- Air bag readiness indicator light
- Anti-lock brakes system
- B5 c1
- B7 (below center console)
- Brake fluid level switch (on left rear of engine compt, in brake fluid reservoir)
- Brake system warning ind light
- C10
- C11
- C16 (at left rear corner of engine compartment, on inner fender panel)
- C16 (at left rear corner of engine compt, on inner fender panel)
- C16 (on inner fender panel)
- Charging system warning ind light
- Check 4wd warning indicator light
- Check trans indicator light
- Cruise control system
- Dash fuse box (behind left side of dash, behind panel)
- Diode box b
- Electronic brake control module (on right rear corner of engine compt)
- Electronic suspension system
- Engine control module (ecm) (below center of dash)
- Engine controls system
- Engine coolant temp gauge
- Exterior lights system
- Fuel gauge
- Fuel in
- Fuel tank sender
- Fuel tank unit (beneath rear of vehicle, in top of fuel tank)
- Fuse 11 meter 15a
- Fuse 13 ecm 15a
- Fuse/relay box (on right side of engine compt)
- Headlights system
- High beam indicator light
- Hot at all times
- Hot in on or start
- Illumination
- Intelligent suspension system warning ind light
- Interior lights system
- Lcd bulb
- Left turn indicator light
- Low fuel warning indicator light
- M/t
- Malfunction indicator check engine light
- Meter assembly
- Multi-plexed indicator control unit (below rear of center console)
- Nca
- Odo/ trip meter
- Oil pressure indicator light
- Oil pressure switch (on lower right side of engine, near oil filter)
- Pnk
- Power drive indicator light
- Prm in
- Right turn indicator light
- Seat belt reminder indicator light
- Sns gnd
- Speedo- meter
- Sport mode ind
- Starting/charging system
- Tachometer
- Transmissions system
- U/s ind
- U/s ind low fuel ctrl light
- Upshift indicator light
- Warning system
- Winter drive indicator light
3.2L
3.2L, Instrument Cluster Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 3.2L, Instrument Cluster Wiring Diagram for Isuzu Rodeo S 2003:
- (beneath center console, on parking brake lever) parking brake switch
- 4l indicator light
- 4wd indicator light
- A/t fluid indicator light
- Abs indicator light
- Air bag readiness indicator light
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- Anti-lock brakes system
- Anti-theft system
- B7 (below center console)
- Brake fluid level switch (on left rear of engine compt, in brake fluid reservoir)
- Brake system warning ind light
- C16 (at left rear corner of engine compartment, on inner fender panel)
- C16 (at left rear corner of engine compt, on inner fender panel)
- C16 (on inner fender panel)
- Charging system warning ind light
- Check 4wd warning indicator light
- Check trans indicator light
- Cruise control system
- Cruise set indicator light
- Dash fuse box (behind left side of dash, behind panel)
- Diode box b
- E21
- E22
- E42
- Electronic brake control module (on right rear corner of engine compt)
- Electronic suspension system
- Engine control module (left rear of engine compartment)
- Engine controls system
- Engine coolant temperature gauge
- Exterior lights system
- From reduced power indicator light
- Fuel gauge
- Fuel out
- Fuel tank sender
- Fuel tank unit (beneath rear of vehicle, in top of fuel tank)
- Fule in
- Fuse 11 meter 15a
- Fuse 13 ecm 10a
- Fuse 14 back up/ turn light 15a
- Fuse/relay box (on right side of engine compt)
- Headlights system
- High beam indicator light
- Hot at all times
- Hot in on or start
- Illumination
- Immobilizer warning indicator light
- Intelligent suspension system warning ind light
- Interior lights system
- Lcd bulb
- Left turn indicator light
- Low fuel warning indicator light
- Malfunction indicator check engine light
- Meter assembly
- Nca
- Odo/ trip meter
- Oil pressure indicator light
- Oil pressure switch (on lower front of engine, near oil filter)
- Pnk
- Power drive indicator light
- Reduced power indicator light
- Right turn indicator light
- Rpm out
- Seat belt reminder indicator light
- Sns gnd
- Speedometer
- Sport mode ind
- Starting/charging system
- Tachometer
- To engine coolant temperature gauge
- Transmissions system
- Upshift indicator light
- Warning system
- Winter drive indicator light
INTERIOR LIGHTS
Courtesy Lamps Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Courtesy Lamps Wiring Diagram for Isuzu Rodeo S 2003:
- (below center console) b7
- 3.2l
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- B7 (below center console)
- Combination swtich
- Dash fuse box (behind left side of dash, behind panel)
- Dash fuse box (behind left side of dash, behind panel)
- Diode box 5
- Diode box 6
- Dome light
- Door
- Engine controls, anti-theft systems
- Exterior lights system
- Fuse 4 tail/illum light 15a
- Fuse 5 dome light 10a
- Hatch gate open switch
- Head
- Hot at all times
- I-42
- Keyless entry & anti-theft control unit (behind right side of dash, above kick panel)
- Left front door switch
- Left front vanity mirror light
- Left map light
- Left map light switch
- Left rear door switch
- Lighting switch
- Luggage room light
- Off
- Park
- Rear view mirror
- Red
- Right front door switch
- Right front vanity mirror light
- Right map light
- Right map light switch
- Right rear door switch
- Taillamp relay
- Wiper/washer system
Instrument Illumination Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Instrument Illumination Wiring Diagram for Isuzu Rodeo S 2003:
- (2 bulbs)
- (w/ amplifier)
- (w/o amplifier)
- Ashtray light
- B7 (below center console)
- Combination swtich
- Cruise control main switch
- Cruise control remote switch
- Dash fuse box (behind left side of dash, behind panel)
- Drive selector switch
- Engine controls, door locks systems
- Exterior lights system
- Fog light switch
- Glove box light
- Hazard warning switch
- Head
- Heater- a/c control panel
- Hot at all times
- I-2
- Illumination controller
- Illumination controller light
- Intelligent suspension mode switch
- Lighting switch
- Meter assembly
- Nca
- Off
- Park
- Power/ winter switch (2 bulbs)
- Radio
- Radio remote switch
- Rear defogger switch
- Rear wiper switch
- Red
- Shift lock controller
- Solid state
- Srs coil assembly
- Steering wheel
- Switch unit a
- Switch unit b
- Tail/illum light fuse 4 15a
- Taillight relay
POWER DISTRIBUTION
Power Distribution Wiring Diagram (1 of 3) for Isuzu Rodeo S 2003
List of elements for Power Distribution Wiring Diagram (1 of 3) for Isuzu Rodeo S 2003:
- (2.2l) (3.2l)
- (2.2l) ecm or pcm main relay
- (3.2l) (2.2l)
- (on right side of engine compt) fuse/relay box
- (rodeo) (rodeo sport)
- 2.2l
- 3.2l
- 3.2l except s model
- 30a
- Alarm & relay control unit
- Amplifier
- Anti- theft horn (3.2l)
- Anti-theft indicator light
- Battery
- Brake switch
- C-5
- C50
- Cb 21 power window 30a (3.2l)
- Coil
- Condenser fan hi relay
- Condenser fan lo relay
- Condenser fan relay
- Dash fuse box (behind left side of dash, behind panel)
- Data link connector (dlc)
- Dome light
- Driver's power seat switch
- Ecm main relay (3.2l)
- Electronic brake control module (ebcm)
- Engine control module (ecm) (3.2l)
- Engine control module or powertrain control module (2.2l)
- Foglight relay
- Fuel pump relay
- Fuse 1 acc socket 20a
- Fuse 1 hazard 15a
- Fuse 10 fog light 15a (3.2l)
- Fuse 15 ign b1 60a
- Fuse 16 main 100a
- Fuse 17 ecm 30a (3.2l)
- Fuse 19 ign b2 50a
- Fuse 2 b+ (audio) 15a
- Fuse 2 horn 10a
- Fuse 20 elect fan 30a 40a
- Fuse 4 immo- bilizer 10a (3.2l)
- Fuse 4 tail/ illum 15a
- Fuse 5 dome light 10a
- Fuse 6 stop light 15a
- Fuse 7 power door lock 20a
- Fuse abs 50a
- Fuse tcm & tccm 10a (3.2l)
- Generator
- Hazard warning switch
- Headlight relay
- Heater-a/c relay
- I-41
- I-42
- Immobilizer control unit (icu)
- Intelligent suspension control unit
- J/c a
- J/c b
- Key remind switch
- Keyless entry & anti-theft control unit
- Left front power window & door lock switch
- Left map light switch
- Luggage room light
- Meter assembly
- Option box (at right side of engine compt)
- Passenger's power seat switch
- Pnk
- Power window relay
- Radio
- Rear defogger relay
- Rear view mirror
- Red
- Right map light switch
- Rodeo except s model
- Starter relay
- Starter solenoid
- Starter switch
- Taillight relay
- To accessory socket relay (diagram 2 of 3)
- To starter switch (diagram 2 of 3)
- Transfer control unit
- Transmission control module (tcm)
- W/ amplifier
- W/ anti- theft
- W/o amplifier
- W/o anti- theft
Power Distribution Wiring Diagram (2 of 3) for Isuzu Rodeo S 2003
List of elements for Power Distribution Wiring Diagram (2 of 3) for Isuzu Rodeo S 2003:
- (w/ amplifier)
- 2.2l a/t
- 2.2l m/t
- 3.2l
- Acc
- Accessory socket relay
- Alarm & relay control unit
- Amplifier
- Automatic transmission mode switch
- B-15
- B7 (below center console)
- Cigarette lighter
- Clutch start switch
- Dash fuse box (behind left side of dash, behind panel)
- E-21
- Engine control module (ecm)
- From fuse 1 (diagram 1 of 3)
- From fuse 15 (diagram 1 of 3)
- From fuse 19 (diagram 1 of 3)
- Front accessory socket
- Fuse 15 elec ig 15a
- Fuse 16 rear wiper & washer 10a
- Fuse 19 acc (audio) 10a
- Fuse 20 cigar lighter 15a
- Fuse 23 anti-theft 10a
- Fuse 3 starter 10a
- Fuse/relay box (on right side of engine compartment)
- Heater a/c relay
- I-21
- I-22
- I-28
- I-29
- I-41
- Keyless entry & anti-theft control unit
- Lock
- Mirror control switch
- Off
- Pnk
- Power window relay
- Radio
- Rear accessory socket
- Rear defogger relay
- Rear wiper motor (rodeo sport, w/ hard top)
- Rear wiper switch
- Red
- Start
- Starter switch
- Subwoofer amplifier
- To dash fuse box (diagram 3 of 3)
- W/ amplifier
- W/ subwoofer
- W/o amplifier
- W/o subwoofer
Power Distribution Wiring Diagram (3 of 3) for Isuzu Rodeo S 2003
List of elements for Power Distribution Wiring Diagram (3 of 3) for Isuzu Rodeo S 2003:
- (2.2l)
- 2.2l
- 3.2l
- 3.2l a/t
- 3.2l m/t
- A/t
- A1 c4
- Alarm & relay control unit
- Automatic transmission mode switch
- B-26
- Back-up lights switch
- Brake switch
- C-50
- C-78
- Camshaft position (cmp) sensor
- Clutch start switch (3.2l m/t)
- Clutch switch
- Combination switch
- Condenser
- Cruise control main switch
- Dash fuse box (behind left side of dash, behind panel)
- E-64
- E5 c3
- Ecm main relay (3.2l)
- Ecm or pcm main relay
- Electronic brake control module (ebcm)
- Engine or powertrain control module (ecm or pcm)
- Evaporative emission (evap) canister purge valve
- Evaporative emissions (evap) canister vent valve
- Exhaust gas recirculation (egr) solenoid valve
- From starter switch (diagram 2 of 3)
- Fuse 11 meter 15a
- Fuse 12 engine ign 15a
- Fuse 13 ig coil 15a
- Fuse 14 back-up/ turn lights 15a
- Fuse 17 front wiper & washer 20a
- Fuse 22 srs 10a
- Fuse tcm 15a (3.2l)
- Fuse/ relay box (on right side of engine compt)
- Hazard warning switch
- I-1
- I-55
- I-9
- Ignition coil
- Ignition control module (icm)
- Immobilizer control unit (icu) (3.2l)
- Intelligent suspension control unit
- Ion sensing module
- M/t
- Mass airflow (maf) sensor
- Meter assembly
- Meter assembly (3.2l m/t)
- Multiplexed indicator control unit (2.2l)
- Neutral start switch
- Neutral start switch (3.2l a/t)
- Neutral switch
- Red
- Sensing & diagnostic module (sdm)
- Shift lock relay
- Switch unit a
- Transfer control unit
- Transmission control module (tcm)
- Variable intake manifold vacuum switching valve
- Vehicle speed sensor
- Windshield wiper motor
- Windshield wiper/washer switch
POWER DOOR LOCKS
Power Door Locks Wiring Diagram, with Keyless Entry for Isuzu Rodeo S 2003
List of elements for Power Door Locks Wiring Diagram, with Keyless Entry for Isuzu Rodeo S 2003:
- (below center console)
- Anti- theft fuse 23 10a
- B7 (below center console)
- Battery
- Battery input
- Dash fuse box (behind left side of dash, behind panel)
- Door lock switch
- Driver's door lock actuator
- Drv dr lck ctrl
- Front passenger door lock actuator
- Ground
- Hot at all times
- Hot in acc or on
- Ignition input
- Keyless entry & anti-theft control unit (behind right side of dash, above kick panel)
- Lck/unlck out
- Left front door power window & lock switch
- Left rear door lock actuator (rodeo)
- Lock
- Lock input
- Power door lock fuse 7 20a
- Right front door power window & lock switch
- Right rear door lock actuator (rodeo)
- Tailgate door lock actuator (rodeo: at lower right side of tailgate) (rodeo sport: at center of tailgate)
- Unlock
- Unlock input
Power Door Locks Wiring Diagram, without Keyless Entry for Isuzu Rodeo S 2003
List of elements for Power Door Locks Wiring Diagram, without Keyless Entry for Isuzu Rodeo S 2003:
- B7 (below center console)
- Battery
- Dash fuse box (behind left side of dash, behind panel)
- Door lock switch
- Driver's door key switch
- Driver's door lock actuator
- Ground
- Hot at all times
- Key sw in lock
- Key sw in unlk
- Lck/unlck out
- Left front door power window & lock switch
- Left rear door lock actuator (rodeo)
- Lock
- Lock input
- Power door lock fuse 7 20a
- Right front door lock actuator
- Right front door power window & lock switch
- Right rear door lock actuator (rodeo)
- Tailgate door lock actuator (rodeo: at lower right side of tailgate) (rodeo sport: at center of tailgate)
- Unlock
- Unlock input
POWER MIRRORS
Power Mirrors Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Power Mirrors Wiring Diagram for Isuzu Rodeo S 2003:
- (below center console) b7
- Dash fuse box (behind left side of dash, behind panel)
- Defogger
- Defogger system
- Down
- Fuse 18 audio (acc) 10a
- Hot in acc or on
- Left
- Left power mirror
- Left/right
- Mirror control switch
- Mirror selector switch
- Right
- Right power mirror
- Switch 1
- Switch 2
- Switch 3
- Up/down
POWER SEATS
Power Seats Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Power Seats Wiring Diagram for Isuzu Rodeo S 2003:
- B7 (below center console)
- Backward
- C.b. 21 power window 30a
- Dash fuse box (behind left side of dash, behind panel)
- Driver side recline motor
- Driver side slide motor
- Driver's power seat switch
- Forward
- Hot at all times
- Passenger side recline motor
- Passenger side slide motor
- Passenger's power seat switch
- Red
POWER TOP/SUNROOF
Power Top/Sunroof Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Power Top/Sunroof Wiring Diagram for Isuzu Rodeo S 2003:
- (below center console) b7
- Close tilt (pop-up)
- Close/ tilt (pop-up) relay
- Closed during opening,
- Closed in tilt (pop-up) & fully
- Dash fuse box (behind left side of dash, behind panel)
- Elec. ig fuse 15 15a
- Fully open, & closing positions. open in all other positions.
- Hot at all times
- Hot in on
- J-1
- J-2
- Open
- Open positions. open in all other positions
- Open relay
- Pop-up switch
- Power window fuse 21 30a
- Power window relay
- Power window system
- Red
- Safety stop switch
- Solid state
- Sun roof assembly
- Sun roof control unit (center front of roof behind headliner)
- Sun roof motor
- Sun roof switch
POWER WINDOWS
Power Windows Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Power Windows Wiring Diagram for Isuzu Rodeo S 2003:
- (below center console) b7
- (not used)
- B7 (below center console)
- Dash fuse box (behind left side of dash, behind panel)
- Fuse 15 elec ig 15a
- Fuse 21 power window 30a
- Ground
- Hot at all times
- Hot in on
- Left front door power window & lock switch
- Left front power window motor
- Left rear power window motor (rodeo)
- Left rear power window switch (rodeo)
- Multiplex in
- Multiplex out
- Power
- Power tops system
- Power window relay
- Right front door power window & lock switch
- Right front power window motor
- Right rear power window motor (rodeo)
- Right rear power window switch (rodeo)
- Rodeo
- Win mtr ctrl
RADIO
Radio Wiring Diagram, with Amplifier for Isuzu Rodeo S 2003
List of elements for Radio Wiring Diagram, with Amplifier for Isuzu Rodeo S 2003:
- rr - rl - beep rr +
- Amp +
- Amp+ fr - mute fr +
- Amplifier (behind left side of dash)
- Antenna
- Antenna input
- B40
- B41
- B7 (below center console)
- B7 (below center console)
- Cd player (if equipped)
- Ch/ trk
- Cruise control system
- Dash fuse box (behind left side of dash, behind panel)
- E30 (at right side of intake manifold)
- Fl +
- Fl -
- Fl - acc ill-
- Fr +
- Fr -
- Fuse 19 (audio) acc 10a
- Fuse 2 (audio) b+ 15a
- Ground
- Hot at all times
- Hot in acc or on
- I15
- Ill+
- Interior lights system
- Left front speaker
- Left rear door speaker (rodeo)
- Left rear speaker
- Left tweeter
- Memory power
- Mute
- Nca
- Pnk
- Radio
- Radio remote switch
- Red
- Right front tweeter
- Right rear door speaker (rodeo)
- Right rear speaker
- Right tweeter
- Rl +
- Rl -
- Rl - ground
- Rr +
- Rr -
- Srs coil assembly
- Steering wheel
- Twisted wires
- Vol dn
- Vol up
Radio Wiring Diagram, without Amplifier for Isuzu Rodeo S 2003
List of elements for Radio Wiring Diagram, without Amplifier for Isuzu Rodeo S 2003:
- memory power
- (at right side of intake manifold) e30
- + + -
- + + illumination power
- - -
- - ground illumination
- Accessory socket relay
- Antenna
- Antenna input
- B7 (below center console)
- B99 (at right rear floor of cargo area)
- Cb-1 acc socket 20a
- Cb-19 cigar lighter 15a
- Cd player (if equipped)
- Ch/ trk
- Cruise control system
- Dash fuse box (behind left side of dash, behind panel)
- Fuse 19 (audio) acc 10a
- Fuse 2 (audio) b+ 15a
- Hot at all times
- Hot in acc or on
- I15
- Interior lights system
- Left front speaker
- Left rear door speaker (rodeo, if equipped)
- Left rear speaker
- Left tweeter (if equipped)
- Nca
- Pnk
- Radio
- Radio remote switch
- Red
- Right front speaker
- Right rear door speaker (rodeo, if equipped)
- Right rear speaker
- Right tweeter (if equipped)
- Srs coil assembly
- Steering wheel
- Sub woofer amplifier (if equipped)
- Subwoofer
- Vol dn
- Vol up
SHIFT INTERLOCK
Shift Interlock Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Shift Interlock Wiring Diagram for Isuzu Rodeo S 2003:
- B7 (below center console)
- Brake switch (behind left side of dash, on brake pedal support)
- Cb-14 back up/ turn light fuse 15a
- Cb-6 stop light fuse 15a
- Dash fuse box (behind left side of dash, behind panel)
- Hot at all times
- Hot in on or start
- Illumination
- Interior lights system
- Parking position detect switch
- Red
- Shift lock controller
- Shift lock relay (under center console, below shift lever cover)
- Shift lock solenoid
STARTING/CHARGING
Charging Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Charging Wiring Diagram for Isuzu Rodeo S 2003:
- Battery
- Charging system warning light
- Dash fuse box (behind left side of dash, behind panel)
- Fuse c-11 meter 15a
- Fuse eb-16 main 100a
- Fuse eb-3 acg-s 10a
- Fuse/ relay box (on right side of engine compt)
- Generator
- Hot in on or start
- I-1
- J/c b
- Meter assembly
- P10 (at lower right front of engine)
- P6/c36 (at right side of engine compt, behind battery)
- Starting circuit
2.2L
2.2L, Starting Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 2.2L, Starting Wiring Diagram for Isuzu Rodeo S 2003:
- A/t
- Acc
- Automatic transmission mode switch (beneath center of vehicle, on left side of transmission)
- Battery
- Clutch start switch (behind left side of dash, on clutch pedal support)
- Dash fuse box (behind left side of dash, behind panel)
- Fuse cb-3 starter 10a
- Fuse eb-16 main 100a
- Fuse eb-19 ign-b2 50a
- Fuse/ relay box (on right side of engine compt)
- Fuse/relay box (on right side of engine compt)
- J/c a
- Lock
- M/t
- Off
- P10 (at lower right front of engine)
- P6/c36 (at right side of engine compt, behind battery)
- Start
- Starter
- Starter motor
- Starter relay
- Starter solenoid
- Starter switch
3.2L
3.2L, Starting Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 3.2L, Starting Wiring Diagram for Isuzu Rodeo S 2003:
- A/t
- Acc
- Battery
- Clutch start switch (behind left side of dash, on clutch pedal support)
- Dash fuse box (behind left side of dash, behind panel)
- E-21
- E-22
- Engine control module (ecm)/ powertrain control module (pcm) (left rear of engine compt)
- Fuse cb-12 engine ig 15a
- Fuse cb-3 starter 10a
- Fuse eb-16 main 100a
- Fuse eb-19 ign-b2 50a
- Fuse/ relay box (on right side of engine compt)
- Fuse/relay box (on right side of engine compt)
- Hot in on or start
- J/c a
- Lock
- M/t
- Neutral start switch
- Off
- P10 (at lower right front of engine)
- P6/c36 (at right side of engine compt, behind battery)
- Pnk
- Rly ctrl
- Start
- Starter
- Starter motor
- Starter relay
- Starter solenoid
- Starter switch
- Str feed
SUPPLEMENTAL RESTRAINTS
Supplemental Restraints Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Supplemental Restraints Wiring Diagram for Isuzu Rodeo S 2003:
- (below center console) b-7
- (below left side of dash, above kick panel) i-43
- 2.2l
- Air bag readiness indicator light
- Cb-11 meter fuse 15a
- Cb-22 srs fuse 10a
- Dash fuse box (behind left side of dash)
- Data link connector (dlc) (partial) (on lower left side of dash, near engine hood release lever)
- Dlc output
- Driver's inflator module
- Driver's seat belt buckled input
- Driver's seat belt switch (open w/seat belt buckled) (in driver's seat belt buckle)
- Engine controls system
- Gnd
- High
- Hot in on or start
- I-1
- Ignition
- Indicator
- Low
- Meter assembly
- Passenger's inflator module
- Red
- Sensing & diagnostic module (sdm) (below center of dash)
- Serial data
- Srs coil assembly
- Steering wheel
- Warning systems
TRANSMISSION
2.2L
2.2L, A/T Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 2.2L, A/T Wiring Diagram for Isuzu Rodeo S 2003:
- (below left side of dash) data link connector
- (left side of transmission) automatic transmission mode switch
- (on throttle body) throttle position sensor
- Automatic transmission
- B-7 (below center console)
- B13
- Batt
- Braid
- Brake
- Brake switch (on top of brake pedal support)
- Brk band
- C-16 (rear of left front fender)
- C-36 (behind battery)
- Check trans
- D10
- Dash fuse box (left side of dash)
- Data
- E-28 (right rear of engine)
- E14
- E16
- Ect sens
- Engine controls system
- Engine coolant temperature sensor (right rear of engine)
- Exterior lights system
- F11
- F14
- F15
- F16
- Fuse 11 meter 15a
- Fuse 12 engine ig 15a
- Fuse 13 ecm 15a
- Fuse 14 back up/ turn light 15a
- Fuse 6 stop light 15a
- Fuse/ relay box (right side of engine compt)
- Gauge assembly
- Ground
- Hot at all times
- Hot in on or start
- I-1
- I-9
- Ignition
- Interior lights system
- J/c c-37
- Kd sw
- Kick down switch (behind left side of dash)
- M-6
- M-7
- Multi-plexed indicator control unit (rear of center console)
- Pcm main relay
- Pcs +
- Pcs -
- Pnk
- Power
- Power drive
- Power/ winter switch
- Powertrain control module (below center of dash)
- Pressure control solenoid
- Pwr sw
- Red
- Sens rtn
- Shift control
- Sol v+
- Ss a
- Ss b
- Tcc
- Tft sens
- Torque converter clutch pwm solenoid
- Tp sens
- Trans pos
- Transmission fluid temperature sensor
- Transmission speed sensor (on top of transmission)
- Tss
- V+ ref
- Winter
- Winter drive
- Winter sw
3.2L
3.2L, 4WD Wiring Diagram, Shift on the Fly for Isuzu Rodeo S 2003
List of elements for 3.2L, 4WD Wiring Diagram, Shift on the Fly for Isuzu Rodeo S 2003:
- (a/t)
- (left rear inner fender panel) (a/t) e-30
- (m/t)
- (right rear of engine compt) electronic brake control module
- (right side of intake manifold) (m/t) e-30
- (under left side of dash) transmission control module
- 2-4wd switch
- 2h sw
- 4h ind
- 4h sw
- 4l ind
- 4l sw
- 4l-out
- 4l-signal
- 4wd engage
- 4wd ind
- 4wd sig
- 4wd sw
- Automatic transmission mode switch (left side of transmission)
- Axl-m1
- Axl-m2
- Axle sw
- B-19
- B-42
- B-7 (below center console)
- Battery
- C-16 (left rear inner fender panel)
- C-79
- Check 4wd
- Check ind
- Dash fuse box (left side of dash)
- Drive selector switch
- E-30 (right side of intake manifold)
- Front axle motor actuator
- Fuse 11 meter 15a
- Fuse 14 back up/ turn light 15a
- Fuse 14 tcm 10a
- Fuse/ relay box (right side of engine compt)
- Gauge assembly
- Ground
- Hot at all times
- Hot in on or start
- I-1
- I-2
- Ignition
- Interior lights system
- Limit sw1
- Limit sw2
- Limit sw3
- Limit sw4
- Ls1-sw
- Ls2-sw
- Ls3-sw
- Ls4-sw
- M/t
- N sw
- Neutral switch
- Neutral switch (m/t)
- Red
- Shift motor
- T/f-m1
- T/f-m2
- T/m 1-sw
- T/m 1-sw (p)
- T/m 2-sw (n)
- Tach sig
- Transfer actuator
- Transfer control unit (below center console)
- Vehicle speed sensor (rear of trans)
- Vss sig
3.2L, A/T Wiring Diagram for Isuzu Rodeo S 2003
List of elements for 3.2L, A/T Wiring Diagram for Isuzu Rodeo S 2003:
- (left side of transmission) automatic transmission mode switch
- (right side if intake manifold) e-30
- (under left side of dash) transmission control module
- 4l-signal
- A/t oil ind
- A/t oil temp
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- Automatic transmission
- B-7 (below center console)
- Battery
- Brake
- Brake switch (on top of brake pedal support)
- C-78
- C-79
- Can+
- Can-
- Center console)
- Check trans
- Chk tran ind
- Dash fuse box (left side of dash)
- Data link connector (below left side of dash)
- Dgi
- E-21
- E-22
- Engine control module (left rear
- Exterior lights system
- Fuse 11 meter 15a
- Fuse 14 back up/ turn light 15a
- Fuse 14 tcm 10a
- Fuse 18 tcm 15a
- Fuse 6 stop light 15a
- Fuse/ relay box (right side of engine compt)
- Gauge assembly
- Ground
- Hot at all times
- Hot in on or start
- I-1
- I-2
- I-42
- I-9
- Ignition
- Input revolution sensor (near left front exhaust downpipe)
- Interior lights system
- J1850
- Nco
- Ncog
- Of engine compt)
- Oil temp sensor (near right front exhaust downpipe)
- Ot2
- Ot2g
- Output revolution sensor (right side of trans)
- Pnk
- Power
- Power drive
- Power ind
- Power sw
- Power/ winter switch
- Pressure control solenoid
- Red
- Shift indicator
- Sl/slu
- Solenoids
- Sp2
- Sth
- Sthg
- Transfer control unit (below
- Winter
- Winter ind
- Winter sw
- Winter trans
WARNING SYSTEMS
Warning Systems Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Warning Systems Wiring Diagram for Isuzu Rodeo S 2003:
- 3.2l
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- Anti-theft system
- B7 (below center console)
- Battery
- Beeper
- Combination switch
- Dash fuse box (behind left side of dash, behind panel)
- Driver's seat belt switch (in driver's seat belt buckle)
- Drvr's door open input
- Engine controls, anti-theft systems
- Fuse 2 horn 10a
- Fuse 4 tail/illum light 15a
- Fuse 5 dome light 10a
- Fuse 7 (power door lock) 20a
- Fuse meter 15a
- Fuse/ relay box (on right side of engine compt)
- Ground
- Head
- Hot at all times
- Hot in on or start
- I-1
- I-41
- I-42
- Interior lights system
- Key in ign input
- Key reminder switch
- Left front door switch (at left front door striker)
- Lighting switch
- Lights on input
- Meter assembly
- Off
- Park
- Red
- Seat belt warning light
- Starter switch
- Tail light relay
- W/ anti-theft
- W/o anti-theft
WIPER/WASHER
Front Wiper/Washer Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Front Wiper/Washer Wiring Diagram for Isuzu Rodeo S 2003:
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- B7 (below center console)
- C16 (at left rear corner of engine compt, on inner fender panel)
- C36/p6 (at right side of engine compt, behind battery)
- Combination switch
- Dash fuse box (behind left side of dash, behind panel)
- Front wiper & washer fuse 17 20a
- Gnd
- Hot in on or start
- I-41
- I-42
- Ignition
- Int
- Int input
- Off
- Off input
- Park
- Ref
- Run
- Run/park in
- Var int input
- Variable intermittent
- W/ variable intermittent wipers
- Wash
- Wash input
- Windshield washer motor (on right front of engine compartment, in washer fluid reservoir)
- Windshield wiper motor (on right rear corner of engine compartment, on firewall)
- Windshield wiper/washer switch
Rear Wiper/Washer Wiring Diagram for Isuzu Rodeo S 2003
List of elements for Rear Wiper/Washer Wiring Diagram for Isuzu Rodeo S 2003:
- Alarm & relay control unit (behind right side of dash, above right kick panel)
- Anti-theft, interior lights systems
- B7 (below center console)
- C36/p6 (at right side of engine compt, behind battery)
- Dash fuse box (behind left side of dash, behind panel)
- Hatch gate open switch (inside top center of tailgate, on latch assembly)
- Hatch open in
- Hot in on
- I-41
- I-42
- Ignition
- Illum
- Interior lights system
- Park
- Rear wash ctrl
- Rear washer motor (on right front of engine compt, in washer fluid reservoir)
- Rear wiper & washer fuse 16 10a
- Rear wiper motor (inside right side of tailgate, behind trim panel)
- Rear wiper switch
- Red
- Run
- Switch unit b
- Switched +/-
- Wash on input
- Washer
- Wipe mtr ctrl
- Wipe on input
- Wiper