DescriptionThe engine radiator and air conditioner condenser cooling system consists of one fan operated at two different speeds:the first speed is activated at a first coolant temperature level or at a certain air conditioner coolant pressure.The second speed cuts in at a higher temperature or pressure threshold.The fan is operated by two specific relays located in the engine compartment unit.The fan supply line is protected by two specific fuses, located in the engine compartment unit.The fan can only be switched on when the ignition is ON.
Functional description The relays T6 and T7 in the engine compartment unit B1 manage the switching on of the fan N11 at two speeds: their coils are supplied by the ignition-controlled line (15/54), while the power lines are protected by the fuses F6 and F7, of the engine compartment unit B1 . Both are energized by a control signal - earth - coming from the engine control unit M10 . If the engine coolant reaches a first temperature level, or the 4-stage pressure switch K10 indicates to the control unit M10 - pin 9 of connector A - that a first pressure level has been reached, the control unit M10 sends a signal - from pin 50 of connector A - to the fan 1st speed relay, which then sends the supply to the fan N11 via the additional resistor O10 : the fan thus turns at the first speed (slow). If the coolant reaches a higher temperature level, or the 4-stage pressure switch K10 indicates to the control unit M10 - pin 41 of connector A - that a higher pressure has been reached, the control unit M10 sends a signal - from pin 62 of connector A - to the fan 2nd speed relay T7, which sends the supply directly to the fan N11 : the fan then turns at the maximum speed.
0Removing201Refitting213025802-7040A37fuse box cover - r r1. Disconnect the electrical connections at the front (1a, 1b, 1c,1d, 1e, 1f).2. Undo the bolts fixing the control unit.3. Undo the bolts shown fixing the dashboard cover.2004865
0Removing201Refitting211. Ensure that the ignition key is in the OFF position, then disconnectthe negative battery terminal (-).2. Open the maxi fuse box cover.3. Undo the bolts securing the 'maxi-fuse' box to the battery.4. Loosen the bolt fixing the battery terminal (+).5. Release the maxi fuse box from the battery and move it to theside.2004975
5530B14
Follow these precautions:769768768
5530B18
Follow these precautions.769On batteries with an opticam hydrometer,electrolyte level and battery charge status can be monitored qualitativelyby examining the indicator colour: a light, bright colour indicates low electrolytelevel: top up with distilled water;a dark colour without a green area in thecentre indicates that the electrolyte level is correct but chargeis low: recharge the battery; a dark colour with a green area in themiddle indicates that both electrolyte level and charge status arecorrect: no action is necessary. For further details, see DESCRIPTION ANDOPERATION - 5580.768Proceed as follows.Check the battery voltage without loadusing the test device recommended by the Service outlets (e.g. 'MICRO360'). Depending on the voltage values measured,which define the state of charge of the battery, proceed as follows:If the voltage without load is less than12.10 V, replace the battery (see op.). 5530B10).If the voltage without load is over 12.10V but less than 12.50 V, recharge the battery (see op. 5530B14).If the voltage without load is over 12.50V, the battery is efficient.If necessary, top up the electrolyte asfollows.Carefully remove the cap strip.Top up with distilled and deionized water,taking care not to allow electrolyte to splash out.768
0Removing201Refitting21Place the vehicle on a lift.Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2004980
5530B40
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2004986
5530B52
0Removing201Refitting21Proceed with removal 3025534-5530B10battery - r+r .1. Remove the relay/fuse box cover.2. Undo the nut (2a) and disconnect the earth lead (2b) from therelay-fuse box.2004990
5530B60
0Removing201Refitting213025534-5530B10battery - r+r1. Remove the battery drip tray.2. Unscrew bolts (2a) and loosen bolt (2b) securing the batterycradle.3. Move the battery cradle aside.4. Release the belt retaining stud.5. Remove the belt.2005002
0Removing201Refitting213025620-5580E08aerial for alpha code- r r1. Disconnect the electrical connections (1a, 1b) from the ignitionswitch.2. Use a drift and undo the headless bolts (2a); remove the ignitionswitch (2b).7682004913
5520A14
769
5520A16
769
5520A18
0Removing201Refitting211. If necessary, regulate the steering wheel height adjustment lever.2. Undo the bolts fixing the lower trim.3. Remove the lower trim, releasing it from the inner retainersand the steering wheel.2004920
0Removing201Refitting213025915-7055B54under-engine guard -r r1. Disconnect the electrical connection.2. Undo and remove the multi-stage pressure switch.2004745
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Disconnect the electrical connection from the air flow meter.2. Loosen collars (2a) and remove air flow meter (2b) after disconnectingit from the air intake sleeves.2001588
1Refitting210Removing20Refit the variable valve timing electro-magnet and secure by tightening the bolts to the recommended torque.Connect the electrical connection to thevariable valve timing electro-magnet.Proceed with the refitting 3024766-1016A40ignition coil coveron cylinder head- r+r .Connect the battery terminal (-).
1056B50
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Disconnect the electrical connection from the air flow meter.Disconnect the electrical wiring for theflow meter from the fastening on the air intake sleeve.2. Disconnect the oil vapour recirculation pipe from the air intakeduct.3. Undo the bolts (3a) and remove the air intakehouse (3b) completewith air flow meter (3c).2002026
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.Proceed with the removal 3024766-1016A40ignition coil coveron cylinder head- r+r . Discharge the fuel supply pressure withthe tool connected to the specific valve located on the side ofthe fuel manifold pipe.1. Disconnect the electrical connections from the injectors.2. Disconnect the rapid attachment of the fuel supply front pipe,fuel manifold pipe side.3. Release the front fuel delivery pipe from the fastening on theair chamber.2001601
1056B68
0Removing201Refitting211. Remove the clips (1a) and remove the injectors (1b) from thesingle fuel manifold pipe.2. Remove the seals from the injectors.2001605
1056B70
0Removing201Refitting211. Remove the clips (1a) and remove the injectors (1b) from thesingle fuel manifold pipe.2. Remove the seals from the injector2001606
1056B78
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Disconnect the electrical connection from the switch on the clutchpedal.2. Turn the switch clockwise through 90 degrees and remove.2001607
1056B81
Make sure that the ignition key is in theOFF position.Check that the air conditioner is off andthat the accelerator pedal is never pressed.Connect the tool to the diagnostic socketand place the knob in position 3.Connect the Examiner diagnostic equipment.Place the ignition key in the ON position.Using the Examiner, enter the 'ControlUnit Test' ambient.Using the Examiner, enter the 'Active Diagnosis' ambient,then select 'Reset self-adjustment parameters' and 'Idle actuator'.Using the Examiner, press 'Carry out activediagnosis'.Place the ignition key in the OFF positionand wait for 30 seconds.Place the ignition key in the ON positionand wait for 30 seconds.Using the Examiner, re-establish the dialoguewith the engine control system.Using the Examiner, enter the 'Parameters'ambient and select the following tests from the menu - 'Idle recognitiontest - carried out' and 'Idle recognition signals - synchronized'.767If at least one of the parametersdoes not conform, place the ignition key in the OFF position andrepeat the procedure. If this non conformity persists, check thatthe diagnostic cable is correctly connected and check the operationof the instrument.Place the ignition key in the OFF positionand wait for 30 seconds.Start up the engine without acting on theaccelerator pedal.Disconnect the diagnostic equipment.Test the vehicle by driving for severalkilometres then, with the engine warmed up, check that it is idlingcorrectly.
1056B82
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Disconnect electrical connections (1a) and (1b) from the injection-ignitioncontrol unit.2. Release the electrical wiring from the fastening on the ignition/injectionsystem control unit mount.2001608
1056B87
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Disconnect electrical connections (1a) and (1b) from the injection-ignitioncontrol unit.2. Release the electrical wiring from the fastening on the ignition/injectionsystem control unit mount.2001610
1056B90
0Removing201Refitting21Position the vehicle on the ramp.Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Disconnect the fuel vapour recirculation pipe from the air inakesleeve.2. Disconnect the intake hose from the throttle body integratedwith D.V.L. and move to one side.2001616
1056B10
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 3024825-1048A28vacuum air circuit resonatorpipe - r+r . 1. Disconnect the electrical connection from the air flow meter. 2. Undo the nuts (2s) and remove the brackets (2b) securing theair flow meter to the aiar filter cover.3. Remove the air flow meter (3a), complete with hose (3b).2067872
1056B62
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-).Proceed with removal 3024979-1072B42left hand or right handinlet manifold (one) - r+r .Discharge the fuel system pressure withthe tool connected to the bleed valves on the fuel pipe.1. Disconnect the quick-release connector for the front fuel supplypipe, fuel pipe side.2. Disconnect the electrical connections from the injectors.3. Undo the bolts (3a) and remove the fuel pipe (3b) complete withinjectors (3c).769Avoid working with the engine hot underall circumstances;Never use tools such as pliers, screwdrivers,etc. under any circumstances;If it is released, rotate the rapid connectorcover before acting on the release buttons;Check its condition (deformation/breakageof retaining lugs, release buttons) before reconnecting it;After re-engageing the rapid connector,check that it is correctly attached by pulling it;At the end of fitting, check that thereare no fuel leaks by starting up the engine again;If there is damage to the rapid connector,replace the complete right pipe.2067877
1056B66
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-).Discharge the fuel system pressure withthe tool connected to the bleed valve on the left fuel pipe.1. Disconnect the electrical connections from the left injectors.2. Disconnect the quick-release connector for the front fuel supplypipe, fuel pipe side.3. Disconnect the rapid connector from the right fuel manifold pipeto the left one.769Avoid working with the engine hot underall circumstances;Never use tools such as pliers, screwdrivers,etc. under any circumstances;If it is released, rotate the rapid connectorcover before acting on the release buttons;Check its condition (deformation/breakageof retaining lugs, release buttons) before reconnecting it;After re-engageing the rapid connector,check that it is correctly attached by pulling it;At the end of fitting, check that thereare no fuel leaks by starting up the engine again;If there is damage to the rapid connector,replace the complete right pipe.4. Undo the bolts (4a) and remove the left fuel manifold pipe (4b)complete with injectors (4c).2067878
1056B67
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-).Proceed with removal 3024979-1072B42left hand or right handinlet manifold (one) - r+r .Discharge the fuel system pressure withthe tool connected to the bleed valve on the right fuel pipe.1. Disconnect the electrical connections from the right injectors.2. Disconnect the rapid connector connecting the right fuel manifoldpipe to the left one.769Avoid working with the engine hot underall circumstances;Never use tools such as pliers, screwdrivers,etc. under any circumstances;If it is released, rotate the rapid connectorcover before acting on the release buttons;Check its condition (deformation/breakageof retaining lugs, release buttons) before reconnecting it;After re-engageing the rapid connector,check that it is correctly attached by pulling it;At the end of fitting, check that thereare no fuel leaks by starting up the engine again;If there is damage to the rapid connector,replace the complete right pipe.3. Undo the bolts (3a) and remove the right fuel manifold pipe (3b)complete with injectors (3c).2067879
pressure pump electric control
1060G10
0Removing201Refitting213025534-5530B10battery - r+r1. Undo collar (1a) and remove the sleeve (1b) from air cleanerto flow meter.2. Disconnect the air flow meter from the underlying sleeve.3. Disconnect the electrical connection from the air flow meter.4. Remove the air flow meter.2002316
1060G14
0Removing201Refitting213025534-5530B10battery - r+rDisconnect the battery negative terminal. 1. Disconnect the water temperature sensor electrical connection.2. Undo the thermostat water temperatur sensor and remove.2002317
1060G16
0Removing201Refitting21Disconnect the battery negative (-) terminal.3025001-1016A10sound-proofing cover - r + r1. Disconnect the electrical connection from the excess pressuresensor.2. Withdraw the retaining bolt.3. Remove the excess pressure sensor2002318
1060G18
0Removing201Refitting21Disconnect the battery negative terminal.1. Disconnect the electrical connection from the fuel temperaturesensor.2. Undo and remove the fuel temperature sensor.2002319
1060G20
0Removing201Refitting21Place the car on a ramp.Disconnect the battery negative terminal.3025915-7055B54under-engine guard - r r1. Disconnect the electrical connection for the rpm sensor.2. Undo bolts (2a) and remove rpm and timing sensor (2b).2002320
0Removing201Refitting21Ensure that the ignition key is in theOFF position, then disconnect the negative battery terminal (-). Proceed with removal 3025001-1016A10sound-proofing cover- r + r . 1. Disconnect the electrical connection from the fuel pressure sensoron the fuel manifold.2. Undo and remove the fuel pressure sensor on the fuel manifold.2068090
0Removing201Refitting21Disconnect the battery negative terminal.1. Disconnect the electrical connection from the switch on the clutchpedal.2. Turn the switch clockwise through 90 degrees and remove.2002322
0Removing201Refitting21Disconnect the battery negative terminal.1. Disconnect the electrical connection from the injection electroniccontrol unit.2. Undo the retaining nuts.3. Remove the engine control unit from its seat on the strut.2002332
0Removing201Refitting21Ensure that the ignition key is in theOFF postition, then disconnect the battery negative terminal.1. Disconnect the electrical connections from the engine coolingfan resistor.2. Undo the bolts (2a) and remove the resistor for the engine coolingfan (2b).2002162
1088E80
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2. Disconnect the electrical connections.3. Open the wiring retaining duct.4. Move the earth wiring away from the duct.2001797
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.