DescriptionThe control unit built into the controls unit on the door controls the operation of the driver's and passenger's electric window motors.The driver's and passenger's motors are controlled in both manual and automatic mode, in accordance with the following logic:For the driver's window:if the button is pressed for between 60 and 300 milliseconds, the operation is manual: the window closes/opens only when the button is pressed;if the button is pressed for over 300 milliseconds, the operation is instead automatic: even if the relevant button is released, the window continues to close/open as far as the end of travel or until the anti-collision safety system intervenes, if applicable;a subsequent press on the button during movement of the window locks it in its current position;if the button is pressed for less than 60 milliseconds, it is ignored (it is considered to have been knocked accidentally).for the passenger's window:closing is only manual;opening is automatic, the same as for the driver's windowIn the case of inconsistent commands issued simultaneously from the driver's and passenger's side, there is no movement.At each press of the electric windows control buttons, a confirmation beep is emitted by the buzzer in the instrument panel.The control unit of the controls unit on the door also acquires information on the possible presence of an obstacle during movement of the window during closing via the anti-collision seals: in this case the window travel stops immediately and is reversed; this happens in both manual and automatic operation.The circuit is controlled by the services relay and protected by two fuses, all located in the unit under the dashboard.Movement takes place whether the ignition in ON or OFF.With the ignition on, it takes place as described above; in addition during starting, this relay is temporarily deactivated.When the ignition is off, the Body Computer keeps the relay activated - which also supplies the door mirrors - for 3 minutes, but deactivates it immediately when one of the two front doors is opened.Movement is also disabled when the battery voltage is below 10 V. The windows are automatically opened or closed by the specific prolonged command (over 4 seconds) sent by the remote control button, if the ignition is off; for more details 3023301SeeE3040CENTRAL LOCKING .
Functional description The services relay T13, located in the unit under the dashboard B2 , supplies with the above-mentioned logic and controlled by the Body Computer M1 - pin 14 of connector F - the controls unit on the door H44 - pins 14 and 25 of connector B, via two lines, protected by the fuses F47 and F48. Via the CAN line, the Body Computer M1 is connected to the controls unit on the door H44 . The controls unit on the door H44 is supplied - pin 24 of connector B - from the line protected by the fuse F39 of the unit under the dashboard B2 . The unit H44 contains the commands for the driver's and passenger's windows, which supply - pins 1-2 and 13-14 of connector B - the motors N60 (driver's side) and N61 (passenger's side). Pin 2 of connector A of H44 instead receives the command from the electric window switch on the front door passenger side H50 (this is a simple switch and it does not incorporate any electronics). Pins 1-8 and 2-3 of connector A of H44 receive the signals from the anti-collision sensors K22 and K23 . The aerial receiver P93 sends to the Body Computer M1 the open/close signal for the doors and windows, connecting to pins 21 and 31 of connector A.
0Removing201Refitting213025802-7040A37fuse box cover - r r1. Disconnect the electrical connections at the front (1a, 1b, 1c,1d, 1e, 1f).2. Undo the bolts fixing the control unit.3. Undo the bolts shown fixing the dashboard cover.2004865
0Removing201Refitting211. Ensure that the ignition key is in the OFF position, then disconnectthe negative battery terminal (-).2. Open the maxi fuse box cover.3. Undo the bolts securing the 'maxi-fuse' box to the battery.4. Loosen the bolt fixing the battery terminal (+).5. Release the maxi fuse box from the battery and move it to theside.2004975
5530B14
Follow these precautions:769768768
5530B18
Follow these precautions.769On batteries with an opticam hydrometer,electrolyte level and battery charge status can be monitored qualitativelyby examining the indicator colour: a light, bright colour indicates low electrolytelevel: top up with distilled water;a dark colour without a green area in thecentre indicates that the electrolyte level is correct but chargeis low: recharge the battery; a dark colour with a green area in themiddle indicates that both electrolyte level and charge status arecorrect: no action is necessary. For further details, see DESCRIPTION ANDOPERATION - 5580.768Proceed as follows.Check the battery voltage without loadusing the test device recommended by the Service outlets (e.g. 'MICRO360'). Depending on the voltage values measured,which define the state of charge of the battery, proceed as follows:If the voltage without load is less than12.10 V, replace the battery (see op.). 5530B10).If the voltage without load is over 12.10V but less than 12.50 V, recharge the battery (see op. 5530B14).If the voltage without load is over 12.50V, the battery is efficient.If necessary, top up the electrolyte asfollows.Carefully remove the cap strip.Top up with distilled and deionized water,taking care not to allow electrolyte to splash out.768
0Removing201Refitting21Place the vehicle on a lift.Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2004980
5530B40
0Removing201Refitting21Open the bonnet lid.1. Release the retainers (1a) and remove the cover (1b).2004986
5530B52
0Removing201Refitting21Proceed with removal 3025534-5530B10battery - r+r .1. Remove the relay/fuse box cover.2. Undo the nut (2a) and disconnect the earth lead (2b) from therelay-fuse box.2004990
5530B60
0Removing201Refitting213025534-5530B10battery - r+r1. Remove the battery drip tray.2. Unscrew bolts (2a) and loosen bolt (2b) securing the batterycradle.3. Move the battery cradle aside.4. Release the belt retaining stud.5. Remove the belt.2005002
0Removing201Refitting213025620-5580E08aerial for alpha code- r r1. Disconnect the electrical connections (1a, 1b) from the ignitionswitch.2. Use a drift and undo the headless bolts (2a); remove the ignitionswitch (2b).7682004913
5520A14
769
5520A16
769
5520A18
0Removing201Refitting211. If necessary, regulate the steering wheel height adjustment lever.2. Undo the bolts fixing the lower trim.3. Remove the lower trim, releasing it from the inner retainersand the steering wheel.2004920
0Removing201Refitting211. Release and gently extract the switch unit.2. Disconnect the electrical connections.3. Recover the switch unit.2005147
7005M14
0Removing201Refitting211. Unscrew the bolt.2. Gently extract the switch unit and control unit.3. Disconnect the electrical connections (3a, 3b).4. Recover the switch unit and control unit.2005148
0Removing201Refitting211. Unscrew the motor retaining bolt.2. Disconnect the motor electrical connection.3. Remove the motor (3a) releasing the toothed wheel (3b) from thecam rack.2004835
0Removing201Refitting211. Unscrew the motor retaining bolt.2. Disconnect the electrical connections for the motor (2a, 2b,2c, 2d).3. Remove the motor (3a) releasing its connection (3b).2004840
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.