AIR CONDITIONING
Automatic A/C Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for Automatic A/C Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011:
- A/c output
- Ambient
- Ambient air temperature sensor (front of upper radiator support)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Blend door cool
- Blend door heat
- Blower
- Blower motor
- Blower motor relay
- Blower motor speed control (right rear of engine compt)
- C228a
- C228b
- C260
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Eatc hvac module
- Fuse 10a
- Fuse 15a
- Fuse 40a
- G109 (front of right fender)
- G203 (right kick panel)
- Ground
- Hi blower
- Hot at all times
- Hot in run
- In car
- In-vehicle temperature sensor (center of dash)
- Interior lights system
- Pot feed
- Pot feedback
- Pot rtn
- Pwm illum
- Pwr gnd
- Run
- S121
- S207
- Scp +
- Scp -
- Sens rtn
- Steering wheel ctrl
- Sun load
- Variable volt dim
- Vbatt
- Vbc
- Vbc feedback
- Vbc hbr
- Vbc input
- Vbc output
Automatic A/C Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Automatic A/C Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (engine control sensor & fuel charge wiring harness, near breakout to cop 4)
- (top of steering column) clockspring
- A/c clutch field coil (lower right front of engine)
- A/c clutch relay
- A/c cycling switch 1) open at 159kpa (23psi) 2) close at 290kpa (42psi)
- A/c pressure transducer
- Accr ctrl
- Accs
- Acpt
- Audio unit
- Audio/climate control switch
- Autolamp sensor
- Autolamp sensor (under upper left side of dash)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C139
- C175b
- C175e
- C175t
- C192
- C2145a
- C218a
- C218b
- C237
- C260
- C290a
- Control solid state
- Engine controls system
- Engine cooling fan module (left front of engine compt)
- Engine cooling fan motor
- Fcv
- Fuse 15a
- Fuse 50a
- G102 (front of left fender)
- G109 (front of right fender)
- G201 (right kick panel)
- G203 (right kick panel)
- Ground
- Hot at all times
- Hot in start or run
- Interior lights system
- Lighting control module (under center of dash)
- Next
- Patil
- Powertrain control module (pcm) (left rear of engine compt)
- Pwr
- Red
- Remote
- S114
- S123 (engine control sensor & fuel charge wiring harness, near breakout to powertrain control module (pcm))
- S126
- S201
- S210
- S294 (in breakout to steering wheel/ speed control switch)
- Sig rtn 1
- Temp+
- Temp-
- Temperature blend door actuator (right side of dash, on top of a/c plenum)
- Var spd in
- Vol+
- Vol-
- Vref
Manual A/C Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Manual A/C Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (engine control sensor & fuel charge wiring harness, near breakout to cop 4)
- (left rear of engine compt)
- (w/ police)
- A/c clutch diode
- A/c clutch field coil (lower right front of engine)
- A/c clutch relay
- A/c cycling switch 1) open at 159kpa (23psi) 2) close at 290kpa (42psi)
- A/c max a/c
- A/c pressure transducer
- Accr ctrl
- Accs
- Acpt
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Blower motor
- Blower motor relay
- Blower motor resistor (right rear of engine compt)
- C139
- C175b
- C175e
- C192
- C237
- C260
- C294a
- C294b
- C294c
- C294d
- Central junction box (cjb) (left of steering column)
- Climate control assembly
- Control circuit
- Def/floor
- Defrost
- Defrost def/floor
- Engine controls system
- Engine cooling fan module (left front of engine compt)
- Engine cooling fan motor
- Fcv
- Floor
- Fuse 10a
- Fuse 15a
- Fuse 40a
- Fuse 50a
- G102 (front of left fender)
- G109 (front of right fender)
- G203 (right kick panel)
- G204 (right kick panel)
- Ground
- High
- Hot at all times
- Hot in run
- Hot in start or run
- Ill
- Interior lights system
- Low
- Max a/c a/c
- Mid high
- Mid low
- Off
- Pan/floor
- Panel
- Powertrain control module (pcm)
- Pwr
- Red
- S114
- S121
- S122 (right rear of engine compt)
- S123 (engine control sensor & fuel charge wiring harness, near breakout to powertrain control module (pcm))
- S126
- S207
- Sig rtn 1
- Temperature blend door actuator (right side of dash, on top of a/c plenum)
- Test
- Thermal limiter
- Var spd in
- Vref
ANTI-LOCK BRAKES
Anti-lock Brakes Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Anti-lock Brakes Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Abs hydraulic valve control assembly
- Abs module (left front of engine compartment)
- Abs pump motor
- Battery junction box (bjb) (right side of engine compt, behind battery)
- Bpp switch
- Brake fluid level switch (on brake fluid reservoir)
- Brake ind
- Brake pedal position (bpp) switch (top of brake pedal support)
- Brake switch c2145b
- C134
- C140
- C175b
- C211
- C2145a
- C248
- C260
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Ctrl sw ind
- Fuse 10a
- Fuse 20a
- Fuse 40a
- Fuse 7.5a
- G102 (front of left fender)
- G103 (front of left fender)
- G203 (right kick panel)
- G212 (behind left kick panel)
- Hot at all times
- Hot in run or start
- Hs can +
- Hs can -
- Ign sw
- Illum
- Ind
- Instrument cluster (ic)
- Interior lights system
- Left front wheel speed sensor (left front wheel hub assembly)
- Left rear wheel speed sensor (left rear wheel hub assembly)
- Lf gnd
- Lf sen
- Lighting control module (under center of dash)
- Lr gnd
- Lr sen
- Microprocessor
- Nca
- Park brake switch (behind left side of dash, on top of parking brake assembly)
- Pnk
- Powertrain control module (left rear of engine compt)
- Pwr feed
- Pwr gnd
- Red
- Red/ pnk
- Red/pnk
- Rf gnd
- Rf sen
- Right front wheel speed sensor (right front wheel hub assembly)
- Right rear wheel speed sensor (right rear wheel hub assembly)
- Rr gnd
- Rr sen
- Run/start
- S112
- S160
- S201
- S246
- S267
- S276
- Tcs sw
- Tel/ red
- Traction
- Traction control switch
ANTI-THEFT
Forced Entry Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Forced Entry Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to left front door lock actuator) s520
- All doors lock
- Antenna module (base of right "c" pillar)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C248
- C501a
- C501b
- C501c
- C526a
- C526b
- C602a
- C602b
- C715a
- C715b
- C820a
- C820b
- Computer data lines system
- Decklid rel in
- Door lock
- Door unlock
- Dr door ajar sw
- Dr door unlk
- Driver door module (bottom front of left front door)
- Driver side front door ajar switch (top rear of left front door)
- Driver side rear door ajar switch (rear of left rear door)
- Fuse 20a
- G201 (right kick panel)
- G212 (behind left kick panel)
- G420 (right "c" pillar)
- Hot at all times
- Keypad illum
- Keypad input a
- Keypad input b
- Keypad input c
- Logic bat
- Logic gnd
- Nca
- Pass door unlk
- Pass dr ajar sw
- Passenger side front door ajar switch (top rear of right front door)
- Passenger side rear door ajar switch (rear of right rear door)
- Pwr gnd
- Rf ask/fsk sel
- Rf data
- Rf recur enable
- Rf recvr gnd
- Rf recvr pwr
- S217
- S500
- S515
- Scp+
- Scp-
- Vbatt
- Wiring harness, near breakout to air suspension module) s259
Forced Entry Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Forced Entry Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (behind left kick panel)
- (right kick panel) g200
- 1/2
- 3/4
- 5/6
- 7/8
- 9/0
- C213
- C2145a
- C2145b
- C423
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Driver side door lock switch
- Exterior lights system
- Fuse 7.5a
- G212
- G212 (behind left kick panel)
- G406 (bottom center of rear seat)
- Horn
- Horns system
- Hot at all times
- Hot in run or acc
- Illumination
- Keyless entry keypad
- Left front door lock actuator (rear of left front door)
- Left rear door lock actuator (rear of left rear door)
- Lighting control module (under center of dash)
- Lock
- Luggage compartment lid release solenoid (center rear of luggage compt lid)
- Luggage compartment lid release switch 1
- Passenger side door lock actuator (rear of right front door)
- Passenger side door lock switch
- Police
- Power distribution system
- Right rear door lock actuator (rear of right rear door)
- S229
- S254
- S260 (body main wiring harness, near breakout to g212)
- S261 (body main wiring harness, near breakout to g212)
- S403
- S500
- S503 (body main wiring harness, near breakout to driver's door module)
- S510 (body main wiring harness, near breakout to exterior rearview mirror switch)
- S600
- Scp+
- Scp-
- Trunk ajar
- Unlock
Passive Anti-theft Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Passive Anti-theft Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Autolamp sensor (under upper left side of dash)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C139
- C175b
- C175t
- C260
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Except police
- Fuse 10a
- G201 (right kick panel)
- Ground
- Hot at all times
- Hot in start or run
- Hs can+
- Hs can-
- Passive anti-theft system (pats) transceiver (steering column)
- Patil
- Power distribution system
- Powertrain control module (pcm) (left rear of engine compt)
- Rx in
- S210
- Smc
- Starter relay
- Tx out
- Vol
BODY CONTROL MODULES
Body Control Modules Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Body Control Modules Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- All doors lock
- Antenna
- Battery junction box (bjb) (right front of engine compt,
- Behind battery)
- C248
- C501a
- C501b
- C501c
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Decklid release input
- Decklid release sol
- Defogger system
- Door lock
- Door locks system
- Door unlock
- Dr door unlock
- Driver door ajar sw
- Driver door module (bottom front of left front door)
- Fuse 20a
- Fuse 7.5a
- G201 (right kick panel)
- G212 (behind left kick panel)
- G420 (right "c" pillar)
- Headlights system
- Hi beam disable
- Hot at all times
- Htd backlight sw
- Htd backlite
- Interior lights system
- Keypad illum
- Keypad input a
- Keypad input b
- Keypad input c
- Logic bat
- Logic gnd
- Nca
- Passenger door ajar sw
- Passenger door unlock
- Pwr gnd
- Rf ask/fsk sel
- Rf data
- Rf recur enable
- Rf recvr gnd
- Rf recvr pwr
- S217
- S254
- S500
- S515 (body main wiring harness, near breakout to driver's door module)
- Scp+
- Scp-
- Trunk, tailgate, fuel doors system
- V batt
- Variable volt dim
COMPUTER DATA LINES
Computer Data Lines Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Computer Data Lines Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (dash panel to headlight junction harness, near breakout to g102)
- (dash panel to headlight junction harness, near breakout to g102) s105
- (dash panel to headlight junction wiring harness, near breakout to air suspension module)
- (main wiring harness,
- Anti-lock brake system(abs)
- C175b
- C213
- C2131a
- C2145a
- C228a
- C248
- C260
- C260 c213
- C310a
- C3281a
- C501a
- Central junction box (cjb) (left of steering column)
- Data link connector (dlc) (under left side of dash)
- Driver door module (bottom front of left front door)
- Feps
- Fire suppression system module (if equipped) (under rear seat)
- Fuse 20a
- G107 (left rear of engine compt)
- G203 (right kick panel)
- Hot at all times
- Hs can+
- Hs can-
- Hvac module, eatc
- Instrument cluster (ic)
- Iso9141
- Lighting control module (under center of dash)
- Module
- Power distribution system
- Powertrain control module (left rear of engine compt)
- Restraints control module (rcm) (below center of dash)
- S106
- S118
- S201
- S216
- S277
- S278 (dash panel to headlight junction wiring harness, near breakout to air suspension module)
- S296 (main wiring harness, in breakout to data link connector (dlc))
- S297 (main wiring harness, in breakout to data link connector (dlc))
- Scp+
- Scp-
- Suppression module)
- Vehicle dynamics module (right end of dash)
- W/ police
COOLING FAN
Cooling Fan Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Cooling Fan Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C110
- C139
- C175e
- Cht
- Cylinder head temperature sensor (top left front of engine)
- Engine controls system
- Engine cooling fan module (left front of engine compt)
- Engine cooling fan motor
- Fcv
- Fuse 50a
- G102 (front of left fender)
- Ground
- Hot at all times
- Powertrain control module (pcm) (left rear of engine compt)
- Pwr
- Red
- S123 (engine control sensor & fuel charge wiring harness, near breakout to powertrain control module (pcm))
- Sig rtn
- Var spd in
CRUISE CONTROL
Cruise Control Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Cruise Control Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (dash panel to headlight junction harness, near breakout to powertrain control module (pcm))
- (on throttle body)
- (steering wheel control switch jumper harness, in breakout to steering wheel/ speed control switch) s294
- (steering wheel control switch jumper harness, in breakout to steering wheel/speed control switch)
- Accelerator pedal position sensor (under left side of dash)
- Anti-lock brake system (abs) module (left front of engine compt)
- App
- App2
- App3
- Appref
- Apprtn2
- Appvref2
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Bps
- Brake pedal position (bpp) switch (top of brake pedal support)
- C175b
- C175e
- C175t
- C211
- C2145b
- C218a
- C218b
- C2330a
- C2330b
- C248
- C260
- Central junction box (cjb) (left of steering column)
- Clockspring (top of steering column)
- Coast
- Computer data lines system
- Electronic throttle control (etc) motor (right rear of engine)
- Engine controls system
- Etcref
- Etcrtn
- Fuse 20a
- Fuse 7.5a
- G203 (right kick panel)
- G212 (behind left
- Hot at all times
- Hs can+
- Hs can-
- Illumination
- Interior lights system
- Kick panel)
- Lighting control module (lcm) (under center of dash)
- Off
- Oss
- Output shaft speed (oss) sensor (left side of transmission)
- Powertrain control module (pcm) (left rear of engine compt)
- Red
- Resume
- S130
- S147 (engine control sensor & fuel charge wiring harness, near breakout to pcm)
- S201
- S246
- S267
- S292
- S293
- S294
- S295 (steering wheel control switch jumper harness, in breakout to audio/ climate control switch)
- Sccs
- Sccsrtn
- Set
- Set +
- Set -
- Sigrtn
- Sigrtn1
- Speed control deactivator switch
- Steering wheel/speed control switch
- Tacm+
- Tacm-
- Throttle position (tp) sensor
- Tp1
- Tp2
- W/ steering wheel audio climate control switch
- W/o steering wheel audio climate control switch
DEFOGGERS
Defoggers Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Defoggers Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (right front of
- Ant pwr
- Antenna module (base of right "c" pillar)
- Audio system
- Battery junction box (bjb)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Behind battery)
- C213
- C214
- C237
- C402a
- C402b
- C501a
- C501b
- Def pwr
- Driver door module (bottom front of left front door)
- Engine compt,
- Fuse 10a
- Fuse 40a
- G200 (right kick panel)
- G203 (right kick panel)
- G212 (behind left kick panel)
- Hot at all times
- Htd back- life sw
- Htd backlife
- Interior lights system
- Left exterior rear view mirror
- Nca
- Off
- Rear window defrost grid
- Rear window defrost relay
- Rear window defrost switch
- Right exterior rear view mirror
- S180
- S190
- S207
- S228
- S500
- S600
ELECTRONIC SUSPENSION
Electronic Suspension Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Electronic Suspension Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to c423) s450
- (front of right fender)
- (right end of dash)
- (right front of engine compt, behind battery) battery junction box (bjb)
- (under rear of vehicle, attached to control arm) air suspension height sensor
- Air suspension compressor assembly (left front side of engine compt)
- Air suspension compressor relay
- Air suspension disable switch (luggage compt, on left support)
- Backht a
- Batt
- Battery junction box (bjb) (right front of engine compartment, behind battery)
- C2131a
- C2131b
- C260
- C465
- Central junction box (cjb) (left of steering column)
- Compressor
- Computer data lines system
- Fuse 10a
- Fusible link 112 30a
- G102 (front of left fender)
- G109
- G109 (front of right fender)
- G405 (bottom center of rear seat)
- Gnd
- Hot at all times
- Hot in run
- Hs can+
- Hs can-
- Ht sens pwr
- Left rear air spring solenoid valve (left rear of vehicle)
- Lh sol
- Nca
- On/off sw
- Pnk
- Return
- Rh sol
- Right rear air spring solenoid valve (right rear of vehicle)
- S112
- S113
- S121
- S490
- Sw ign
- Vehicle dynamics module (vdm)
- Vent
- Vpwr
ENGINE PERFORMANCE
4.6L FLEX FUEL
4.6L Flex Fuel, Engine Performance Wiring Diagram (1 of 6) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for 4.6L Flex Fuel, Engine Performance Wiring Diagram (1 of 6) for Ford Crown Victoria Police Interceptor 2011:
- Accelerator pedal position sensor (under left side of dash)
- Accr
- Accs
- Acpt
- Air conditioning system
- Anti-theft system
- Antilock brakes system
- App
- App2
- App3
- Apprtn2
- Appvref
- Appvref2
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Bps
- C175b
- C192
- C248
- C260
- Case gnd
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Cruise control system
- Evap can vent
- Feps
- Fpc
- Fpm
- Ftp
- Ftpref
- Fuse 10a
- Fuse 15a
- Fuse 30a
- G106 (left rear of engine compt)
- G107 (left rear of engine compt)
- G109 (front of right fender)
- Gen com
- Hot at all times
- Hot in run or start
- Hs can+
- Hs can-
- Ignition coils relay
- Kapwr
- Pcm power diode
- Pcm power relay
- Power distribution system
- Powertrain control module (pcm) (left rear of engine compt)
- Pspsw
- Pwr gnd
- Rdi
- Red
- Red/pnk
- Rx in
- S118
- S121
- S276
- Sccs
- Sccsrtn
- Sig rtn
- Sigrtn1
- Smc
- Starting/charging system
- Tcs_sw
- Trans ctrl sw
- Transmission control switch (steering column)
- Tx out
- Vpwr
- Vsout
4.6L Flex Fuel, Engine Performance Wiring Diagram (2 of 6) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for 4.6L Flex Fuel, Engine Performance Wiring Diagram (2 of 6) for Ford Crown Victoria Police Interceptor 2011:
- (dash panel to headlight junction harness, near breakout to battery junction box (bjb))
- A/c clutch relay
- Audio control module (acm)
- Battery junction box (bjb) (right front of engine compt, behind
- Battery)
- C192
- C248
- C260
- C275
- C290a
- Evap canister purge valve (top right rear of engine)
- Evap canister vent valve solenoid (under left rear of vehicle)
- Fuel pump relay
- Fuse 10a
- Fuse 15a
- Fuse 20a
- G107 (left rear of engine compt)
- G109 (front of right fender)
- Hot at all times
- Inertia fuel shut-off (ifs) switch (luggage compt, on left support)
- Mass air flow/intake air temperature (maf/iat) sensor (behind air cleaner assembly)
- Police accessory connector (pigtail) (if equipped)
- Red
- Red/pnk
- S118
- S119
- S121
- S165 (dash panel to headlamp junction harness, in breakout to g102)
4.6L Flex Fuel, Engine Performance Wiring Diagram (3 of 6) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for 4.6L Flex Fuel, Engine Performance Wiring Diagram (3 of 6) for Ford Crown Victoria Police Interceptor 2011:
- (bottom center of rear seat) g405
- (engine control sensor & fuel charge wiring harness, near breakout to cop 4)
- (engine control sensor & fuel charge wiring harness, near breakout to powertrain control module (pcm))
- (left front side of luggage compt) fuel pump driver module
- (lower right front of engine) power steering pressure switch
- (on right side center of engine) a/c pressure transducer sensor
- (right side of engine) egr system module (esm)
- (top left front of engine) cylinder head temperature sensor
- (top right front of engine) fuel rail pressure/ temperature sensor
- C110
- C139
- C192
- C248
- C433
- Digital transmission range (dtr) sensor (left side of transmission)
- Dpfe
- Evr
- Fppwr
- Frp
- Frt
- Fuel tank pressure (ftp) sensor (in fuel tank)
- Fuel tank unit (in fuel tank)
- G406 (bottom center of rear seat)
- Heated oxygen sensor (ho2s) 11 (lower right rear of engine, in exhaust manifold)
- Heated oxygen sensor (ho2s) 12 (exhaust, rear of catalyst)
- Heated oxygen sensor (ho2s) 21 (lower left rear of engine, in exhaust manifold)
- Heated oxygen sensor (ho2s) 22 (exhaust, rear of catalyst)
- Map
- Nca
- Red/pnk
- S123
- S126
- S146
- Sigrtn
- Tr1
- Tr2
- Tr3a
- Tr4
- Vpwr
- Vref
4.6L Flex Fuel, Engine Performance Wiring Diagram (4 of 6) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for 4.6L Flex Fuel, Engine Performance Wiring Diagram (4 of 6) for Ford Crown Victoria Police Interceptor 2011:
- (engine control sensor & fuel charge wiring harness, near breakout to pcm)
- (front of left cylinder bank) camshaft position sensor
- (right side of transmission) 4r70e transmission
- Anti-theft system
- C175t
- C213
- Epc
- Fuel level
- Fuel level rtn
- Ho2s 12
- Ho2s 22
- Htr-12
- Htr-22
- Instrument cluster (ic)
- Oss sensor
- Output shaft speed (oss) sensor (left side of transmission)
- Patil
- Powertrain control module (pcm) (left rear of engine compt)
- Red
- S147
- Shift sol a
- Shift sol b
- Sig rtn 1
- Ssa
- Ssb
- Tcc
- Tcc sol
- Tft
- Tr1
- Tr2
- Tr3a
- Tr4
- Tss sen sig
- Turbine shaft speed (tss) sensor (left side of transmission)
4.6L Flex Fuel, Engine Performance Wiring Diagram (5 of 6) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for 4.6L Flex Fuel, Engine Performance Wiring Diagram (5 of 6) for Ford Crown Victoria Police Interceptor 2011:
- Coil on plugs (coil 1: top right front of engine) (coil 2: top right center of engine) (coil 3 & 4: top right rear of engine) (coil 5 & 6: top left front of engine) (coil 7: top left center of engine) (coil 8: top left rear of engine)
- Fuel injectors (inj 1: top right front of engine) (inj 2 & 3: top right center of engine) (inj 4: top right rear of engine) (inj 5 & 6: top left front of engine) (inj 7: top left center of engine) (inj 8: top left rear of engine)
- Ignition transformer capacitor (front of left cylinder bank)
- Knock sensor (top left front of engine)
- Red
- Red/pnk
- S135 (engine control sensor & fuel charge wiring harness, near breakout to heated oxygen sensor (ho2s) no.11)
- S136 (engine control sensor & fuel charge wiring harness, near breakout to heated oxygen sensor (ho2s) 11)
- Tan
- Tan/red
4.6L Flex Fuel, Engine Performance Wiring Diagram (6 of 6) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for 4.6L Flex Fuel, Engine Performance Wiring Diagram (6 of 6) for Ford Crown Victoria Police Interceptor 2011:
- (left rear of engine compt) powertrain control module (pcm)
- (lower right front of engine) crankshaft position sensor
- (right rear of engine) electronic throttle control (etc) motor
- C175e
- C192
- Cht
- Ckp+
- Ckp-
- Cmp
- Cooling fans system
- Cop1a
- Cop2d
- Cop3b
- Cop4g
- Cop5f
- Cop6e
- Cop7c
- Cop8h
- Dpfe
- Evapcp
- Evr
- Fc-v
- Frp
- Frt
- Fuel inj 1
- Fuel inj 2
- Fuel inj 3
- Fuel inj 4
- Fuel inj 5
- Fuel inj 6
- Fuel inj 7
- Fuel inj 8
- G107 (left rear of engine compt)
- Gen mon
- Ho2s-11
- Ho2s-21
- Htr-11
- Htr-21
- Iat
- Ks1+
- Ks1-
- Maf
- Mafrtn
- Map
- Red/pnk
- S118
- S158 (engine control sensor & fuel charge wiring harness, near breakout to c192)
- Sigrtn 1
- Starting/charging system
- Tacm+
- Tacm-
- Tan
- Tan/red
- Vref
EXTERIOR LIGHTS
Accessory Lamps Wiring Diagram, Crown Police (1 of 3) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Accessory Lamps Wiring Diagram, Crown Police (1 of 3) for Ford Crown Victoria Police Interceptor 2011:
- (dash panel harness to police glove box relay/ fuse center)
- (dash panel harness to police glove box relay/ fuse center) s283
- (dash panel harness to police glove box relay/fuse center)
- (emergency jumper wiring harness, near breakout for c422)
- (emergency jumper wiring harness, near breakout to c298) s291
- (power distribution wiring harness, at breakout for police luggage compt relay/fuse center)
- (power distribution wiring harness, at breakout for police luggage compt relay/fuse center) s479
- (power distribution wiring harness, in breakout to police trunk relay/fuse center) s474
- (right kick panel) g220
- (right side of engine compt) wig-wag module
- A1 fuse 2 10a
- A1 relay r2
- A2 fuse 2 5a
- A2 relay r2
- A3 fuse 5a
- A3 relay r2
- A4 fuse 2 10a
- A4 relay r2
- A5 fuse 2 10a
- A6 fuse 2 10a
- A6 relay r2
- B1 fuse 4 5a
- B1 relay 4
- B2 fuse 4 10a
- B2 relay 4
- B3 fuse 4 5a
- B4 fuse 10a
- B4 relay
- B5 fuse 10a
- B5 relay 4
- B6 fuse 10a
- C298
- C422
- G411 (center front of luggage compt)
- Harness to police glove box relay/fuse center)
- Headlights system
- Horns system
- Kick panel) g220
- Nca
- Pnk
- Police glove box relay/ fuse center (glove box)
- Police trunk relay/fuse center (front of luggage compartment)
- S285
- S288
- S289 (emergency jumper wiring harness, near breakout to c263)
- S470
- S472 (power distribution wiring harness, in breakout to police trunk relay/fuse center)
- S476
- S478
- Tan
- Tan s284
Accessory Lamps Wiring Diagram, Crown Police (2 of 3) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Accessory Lamps Wiring Diagram, Crown Police (2 of 3) for Ford Crown Victoria Police Interceptor 2011:
- (center front of luggage compt) g411
- (emergency jumper wiring harness near breakout for g411) s460
- (emergency jumper wiring harness, near breakout for c422) s475
- (front of right fender)
- (luggage compt) strobe control module
- 10a
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C11 fuse 4 20a
- C12 fuse 4 10a
- C260
- C268
- C275
- C4231a
- C4231b
- C4231c
- C4231d
- C4231e
- C4231f
- C4231g
- C4231h
- C4231j
- C431
- Central junction box (cjb) (left of steering column)
- Fuse 20a
- Fuse 40a
- Fuse 50a
- Fuse 7.5a
- G109
- G411 (center front of luggage compt)
- Hot at all times
- Hot in run or acc
- Inline fuse (under right end of dash)
- Left front strobe assembly (left front of engine compt)
- Left grille strobe assembly (behind left side of grille)
- Left rear strobe assembly
- Lh fr
- Lh grille
- Lh rear
- M gnd
- M r/a
- P1 gnd
- P1 r/a
- P2 gnd
- P2 r/a
- Pnk
- Police light bar relay/fuse center (front of luggage compt)
- Police power relay
- Rear deck led flasher
- Red
- Rh fr
- Rh grille
- Rh rear
- Right front strobe assembly (right front of engine compt)
- Right grille strobe assembly (right side of grille)
- Right rear strobe assembly
- S110
- S121
- S279
- S282
- S298
- S464
- S465
- S487 (emergency jumper wiring harness, near breakout for c422)
- Shield
- Tan
- To s468 (diagram 3 of 3)
- Trunk air circulation fan motor (luggage compt)
- W/o police light bar relay/fuse center
- Wiring harness, near breakout to center console)
Accessory Lamps Wiring Diagram, Crown Police (3 of 3) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Accessory Lamps Wiring Diagram, Crown Police (3 of 3) for Ford Crown Victoria Police Interceptor 2011:
- (luggage compt) smart siren amplifier
- (power distribution wiring har- ness, in breakout to police light bar relay/ fuse center)
- (power distribution wiring harness, in breakout to police light bar relay/ fuse center)
- (power distribution wiring harness, in breakout to police light bar relay/fuse center) s466
- (right front of engine) g101
- (right kick panel) g220
- Bar relay/ fuse center (front of luggage compt)
- Battery (right side of engine compt)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C1 fuse 4 10a
- C2 fuse 4 10a
- C2 relay
- C268
- C275
- C3 fuse 4 10a
- C3 relay
- C3257a
- C3257b
- C4 fuse 4 10a
- C4 relay
- C406
- C431
- C5 fuse 4 10a
- C5 relay
- C6 fuse 4 10a
- C6 relay
- C7 fuse 4 10a
- C7 relay
- C8 fuse 4 10a
- From c12 fuse 4 (diagram 2 of 3)
- Fuse 50a
- G100 (front of right fender)
- G411 (center front of luggage compartment)
- Horns system
- Hot at all times
- Pnk
- Police light bar relay/ fuse center (front of luggage compt)
- Police light c8 relay
- Red
- Red/ pnk
- Relay
- Relay/fuse center
- S281
- S299
- S350
- S426
- S462
- S465
- S468
- S469
- Siren speaker (right front of engine compt)
- Strobe/light bar control switches
- Tan
- W/o police light bar
Accessory Lamps Wiring Diagram, Police Option Fuse Holder for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Accessory Lamps Wiring Diagram, Police Option Fuse Holder for Ford Crown Victoria Police Interceptor 2011:
- (bottom center of rear seat) g406
- (dash panel to headlight junction harness, in breakout to g102)
- (left rear of engine compt) powertrain control module (pcm)
- (luggage compartment wiring harness, near breakout to c405)
- (not used)
- Anti-theft system
- Battery junction box (bjb) (right front of engine compt, near battery)
- C202a
- C202c
- C211
- C214
- C2145c
- C248
- C260
- C268
- C408
- C4170a
- C4170b
- Central junction box (cjb) (left of steering column)
- Demand lighting
- Emergency flasher relay 1
- Emergency flasher relay 2
- Emergency flasher relay block (center rear of luggage compartment)
- Engine controls system
- Exterior lamps circuit
- Front flasher connector
- Fuse 20a
- Fuse 25a
- Fuse 40a
- Fuse 50a
- Fuse 7.5a
- G102 (front of left fender)
- G109 (front of right fender)
- G403 (right rear seat)
- Hot at all times
- Hot in run or acc
- Interior lights system
- Left rear police flasher lamp
- Left rear police tray lamp
- Left side spot lamp
- Lighting control module (under center of dash)
- Luggage compartment lid release solenoid (center rear of luggage compt lid)
- Multi-function switch
- Pnk
- Police accessory connector
- Police power relay
- Rear flasher
- Rear flasher relay
- Rear police auxiliary junction box (bottom center of rear seats)
- Red
- Right rear police flasher lamp
- Right rear police tray lamp
- Right side spot lamp
- S112
- S114
- S121
- S165
- S224
- S279
- S403
- S422 (in body main wiring harness, near breakout to c423)
- S433
- Tan
- Vsout c175b
Back-up Lamps Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Back-up Lamps Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to temperature blend door actuator)
- (bottom center of rear seat) g406
- Auto-dimming interior mirror
- C139
- C248
- C260
- C405
- C408
- C423
- C913
- Central junction box (cjb) (left of steering column)
- Digital transmission range (dtr) sensor (left side of transmission)
- E c139
- Fuse 10a
- Hot in run or start
- Left reversing lamp
- Rev- erse
- Right reversing lamp
- S248
- S420
- W/ police
Exterior Lamps Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Exterior Lamps Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to g212) s360
- (bottom center of rear seat g406
- (not used)
- (police)
- (police) s243
- (right kick panel)
- (right kick panel) g203
- (under center of dash) lighting control module (lcm)
- Anti-lock brake system (abs) module
- Auto
- Autolamp on/off
- Batt2
- Bpp sw
- C1010
- C1019
- C202a
- C202c
- C205a
- C211
- C2145a
- C2145b
- C2145c
- C2145d
- C260
- C275
- C405
- C408
- C423
- C428
- Central junction box (cjb) (left of steering column)
- Flasher output
- Flasher power
- Fuse 10 15a 20a (police)
- Fuse 15a
- Fuse 2a
- Fuse 7.5a
- G102 (front of left fender)
- G201
- G203 (right kick panel)
- Grand marquis
- Hazard
- Head
- Headlamp off
- Headlamps on
- Hot at all times
- Hot in run
- Instrument cluster
- Left front cornering lamp (grand marquis)
- Left front park/ turn lamp
- Left front parking lamp (crown victoria)
- Left turn
- License lamps
- Logic batt
- Logic gnd
- Main light switch
- Multi-function switch
- Off
- Park
- Park/tail lamps
- Parklamps on/off
- Police
- Right front cornering lamp (grand marquis)
- Right turn
- S109 (dash panel to headlight junction harness, in breakout to c132)
- S112
- S140 (grand marquis) (turn lights wiring harness, in breakout to c1010)
- S142 (grand marquis) (dash panel to headlight junction harness, near breakout to g106)
- S201
- S210
- S222 (police) (main wiring harness, in breakout to c260)
- S223 (police) (main wiring harness, in breakout to c260)
- S232
- S420
Exterior Lamps Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Exterior Lamps Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (behind center of rear seat)
- (behind left kick panel)
- (no connection)
- (right kick panel)
- 1) normally open 2) brake depressed
- Battery junction box (bjb) (right front of engine compartment, behind battery)
- Brake pedal position (bpp) switch
- C1019
- C211
- C408
- C410
- C411
- Central junction box (cjb) (left of steering column)
- Crown victoria
- Emergency flasher relay 1
- Emergency flasher relay 2
- Emergency flasher relay block (police) (center rear of luggage compartment)
- Fuse 15a
- Fuse 20a
- G109 (front of right fender)
- G204
- G212
- G405
- G410 (center rear of luggage compartment)
- Grand marquis
- High mounted stoplamp
- Hot at all times
- Left rear park/stop/ turn lamp 1
- Left rear park/stop/ turn lamp 2
- Power distribution system
- Red
- Right front park/ turn lamp
- Right front parking lamp (crown victoria)
- Right rear park/stop/ turn lamp 1
- Right rear park/stop/ turn lamp 2
- S114
- S204
- S246
- S267
- S406 (body main wiring harness, near breakout to c423)
- S422 (body main wiring harness, near breakout to c423)
- S490 (w/ air suspension)
- Taxi roof lamp
- Taxi roof lamp switch (taxi dso)
GROUND DISTRIBUTION
Ground Distribution Wiring Diagram (1 of 4) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Ground Distribution Wiring Diagram (1 of 4) for Ford Crown Victoria Police Interceptor 2011:
- (grand marquis)
- (grand marquis) left front park/ turn lamp
- (grand marquis) right front fog lamp
- (grand marquis) right front park/turn lamp
- (not used)
- (pcm))
- A/c clutch diode
- A/c compressor clutch field coil
- Air suspension compressor assembly
- Air suspension compressor relay
- Anti-lock brake system (abs) module
- Battery
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Blower
- Blower motor relay
- Brake fluid level switch
- C1010
- C1019
- C1284
- C1285
- C133
- C1386
- C1393
- C175b
- C192
- C2131a
- C250
- C260
- Data link connector (dlc)
- Engine cooling fan module
- Fog lamp relay
- Fuel pump relay
- G100 (front of right fender)
- G101 (right front of engine)
- G102 (front of left fender)
- G103 (front of left fender)
- G106 (left rear of engine compartment)
- G107 (left rear of engine compartment)
- G108 (front of right fender)
- G109 (front of right fender)
- Grand marquis
- Horn
- Ignition coils relay
- Left front fender ends in harness
- Left front fog lamp
- Left front park/ turn lamp
- Left front parking lamp
- Left headlamp
- Low band radio trunk tray ends in harness
- Mass air flow/ intake air temperature (maf/iat) sensor
- Motor resistor
- Motor speed control
- Nca
- Pcm power relay
- Police power relay
- Powertrain control module (pcm)
- Right front fender ends in harness
- Right front park/turn lamp
- Right front parking lamp
- Right headlamp
- S112 (dash panel to headlamp junction harness, near breakout to c1010)
- S113 (dash panel to headlight junction harness, near breakout to powertrain control module
- S114 (dash panel to headlight junction harness, near breakout to c1010)
- S118 (dash panel to headlight junction harness, near breakout to powertrain control module)
- S121 (dash panel to headlight junction harness, near breakout to battery junction box (bjb))
- S158 (engine control sensor & fuel charge wiring harness, near breakout to c192)
- Shield
- Starter relay
- Vehicle dynamics module (vdm)
- W/ police
- Washer fluid level switch
- Windshield washer pump motor
- Windshield wiper motor
Ground Distribution Wiring Diagram (2 of 4) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Ground Distribution Wiring Diagram (2 of 4) for Ford Crown Victoria Police Interceptor 2011:
- (left of steering column) central junction box (cjb)
- (main wiring harness, near breakout to right footwell courtesy light)
- (w/ steering wheel audio/climate control switch) audio/climate control switch
- (w/ steering wheel audio/climate control switch) steering wheel speed control switch
- (w/o steering wheel audio/climate control switch) steering wheel speed control switch
- Accessory relay
- Adjustable pedal switch
- Audio control module (acm)
- Autolamp sensor
- Base radio
- Brake shift interlock
- C202b
- C202c
- C205a
- C205b
- C2145a
- C2145c
- C217b
- C218a
- C218b
- C228a
- C2330a
- C2330b
- C237
- C240
- C268
- C290a
- C294b
- C294d
- C299
- C310a
- C310b
- C312
- C501b
- C526b
- C602b
- C715b
- C820b
- Climate control assembly
- Clock- spring
- Clockspring
- Data link connector (dlc)
- Driver door module (ddm)
- Driver side front door ajar switch
- Driver side rear door ajar switch
- Eatc, hvac module
- Front cigar lighter
- G109 (police) (front of right fender)
- G201 (right kick panel)
- G202 (right kick panel)
- G203 (right kick panel)
- G204 (right kick panel)
- G420 (right "c" pillar)
- G425 (police) (center front of luggage compartment)
- Horn switch
- Instrument cluster (ic)
- Left footwell courtesy lamp
- Lighting control module (lcm)
- Main light switch
- Message center switch
- Multi-function switch
- Occupant classification system module
- Passenger side front door ajar switch
- Passenger side rear door ajar switch
- Passive anti-theft system (pats) transceiver
- Power point
- Rear window defrost switch
- Restraints control module (rcm)
- Right footwell courtesy lamp
- S201 (main wiring harness, in breakout to adjustable pedal switch)
- S204 (main wiring harness, near breakout to electronic automatic temperature control (eatc) module)
- S207 (main wiring harness, near breakout to rear window defrost switch)
- S210
- S212 (cigar lighter wiring harness, in breakout to front cigar lighter)
- S217 (body main wiring harness, near breakout to c919)
- S294 (steering wheel control switch jumper harness, in breakout to steering wheel/speed control switch)
- Sanyo
- Shield
- Taxi roof lamp ends in harness
- Taxi roof lamp switch
- Temperature blend door actuator
- Traction control switch
Ground Distribution Wiring Diagram (3 of 4) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Ground Distribution Wiring Diagram (3 of 4) for Ford Crown Victoria Police Interceptor 2011:
- (center rear of luggage compartment) (police) emergency flasher relay block
- (crown police) glove box ends in harness
- (crown police) strobe/ light bar control switch
- (emergency jumper wiring harness, near breakout to c263) s299
- (glove box) (crown police) police glove box relay/ fuse center
- (luggage compartment jumper wiring harness, near breakout to c405) s403
- (police w/o fire suppression) instrument cluster (i/c)
- (police) left rear police flasher lamp
- (police) rear police auxiliary junction box
- (police) right rear police flasher lamp
- (sanyo) subwoofer amplifier
- (w/ air
- Brake pedal position (bpp) switch
- C213
- C298
- C311
- C3257a
- C405
- C408
- C4170b
- C423
- C432
- C465
- C466a
- C501b
- C504a
- C510
- Driver door module (ddm)
- Driver side door lock switch
- Driver side front heated seat module
- Driver side front seat adjust switch
- Driver side seat heater switch
- Emergency flasher relay 1
- Emergency flasher relay 2
- Exterior rear view mirror switch
- Fuel pump driver module
- G212 (behind left kick panel)
- G213 (behind left kick panel)
- G220 (right kick panel)
- G403 (right rear seat)
- G405 (bottom center of rear seat)
- G406 (bottom center of rear seat)
- G407 (behind left rear seat)
- High mounted stoplamp
- Keyless entry keypad
- Left exterior rear view mirror
- Left front lumbar control switch
- Left rear air spring solenoid valve
- Left reversing lamp
- License lamps
- Luggage compartment lid release solenoid
- Master window adjust switch
- Nca
- Park brake switch
- R2.a1 relay
- R2.a3 relay
- R2.a4 relay
- R2.a5 relay
- R2.a6 relay
- Red
- Right rear air spring solenoid valve
- Right reversing lamp
- S285 (dash panel harness to police glove box relay/fuse center)
- S315 (power seats harness, near breakout to c311)
- S420 (rear license plate lamp wiring harness, in breakout to c405)
- S490 (w/ air suspension) (main body wiring harness, near breakout to fuel pump driver module)
- S500 (body main wiring harness, near breakout to exterior rearview mirror switch)
- Shield
- Suspension)
- W/ police
Ground Distribution Wiring Diagram (4 of 4) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Ground Distribution Wiring Diagram (4 of 4) for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to passenger side front power window motor)
- (crown police)
- (crown victoria) map reading lamps
- (front of luggage compartment) police trunk relay/ fuse center
- (grand marquis) rear interior/map lamps assembly
- (int lamps wiring harness, in breakout to c913) s902
- (power distribution wiring harness, in breakout to police trunk relay/fuse
- Auto- dimming interior mirror
- C312
- C3281a
- C406
- C410
- C411
- C422
- C4231a
- C4231b
- C4231c
- C610
- C913
- C919
- Center)
- Fire suppression manual switch
- Fire suppression system module (fssm)
- G200 (right kick panel)
- G408 (behind left rear seat)
- G410 (center rear of luggage compartment)
- G411 (center front of luggage compartment)
- Interior spot lamp (police)
- Left rear park/stop turn lamp 2
- Left rear park/stop/ turn lamp 1
- Left vanity mirror lamp
- Passenger side door lock switch
- Passenger side front heated seat module
- Passenger side front seat adjust switch
- Passenger side seat heater switch
- R4.b1 relay
- R4.b4 relay
- Rear deck led flasher
- Right exterior rear view mirror
- Right front lumbar control switch
- Right rear park/stop turn lamp 2
- Right rear park/stop/ turn lamp 1
- Right vanity mirror lamp
- S320 (power seats harness, near breakout to occupant classification sensor module)
- S465 (emergency jumper wiring harness, near breakout for c422)
- S476
- Smart siren amplifier
- Strobe control module
- Trunk air circulation fan motor
- Trunk ends in harness
- Trunk tray ends in harness
HEADLIGHTS
Headlamps Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Headlamps Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (dash panel to headlight junction harness, near breakout to g106) s170
- (dash panel to headlamp junction harness, near breakout to g106)
- (front of left fender)
- (left of steering column)
- (right front of engine compt, behind battery)
- (right kick panel)
- Air conditioning system
- Auto
- Auto lamp on/off (delete for police)
- Auto lamp sens (delete for police)
- Autolamp sensor (under upper left side of dash)
- Batt2
- Batt3
- Batt4
- Batt6
- Battery junction
- Box (bjb)
- Box (cjb)
- C1386
- C1393
- C202c
- C205a
- C205b
- C2145a
- C2145b
- C2145c
- C2145d
- C248
- C260
- Central junction
- Control solid state
- Dim
- Dome
- Dome lamp sw
- Driver door module (police) (bottom front of left front door)
- Fog lamp ind
- Fog lamp relay
- Fog lamp rly
- Fog lamp sw
- Ftp
- Fuse 10a
- Fuse 15a
- G102
- G102 (front of left fender)
- G109 (front of right fender)
- G201 (right kick panel)
- G203
- Head
- Headlamp off
- Headlamps on
- Headlight junction harness, near breakout to g102)
- Hi beam disable c501a
- Hi beam sw
- Hot at all times
- Illumination
- Interior lights system
- Lamps fog
- Left front fog lamp
- Left headlamp
- Left hi beam out
- Left lo beam
- Lighting control module (under center of dash)
- Logic gnd
- Main light switch
- Multi-function switch
- Off
- Panel dimmer
- Park
- Parklamps on/off
- Pnk
- Right front fog lamp
- Right headlamp
- Right hi beam out
- Right lo beam
- S112
- S114
- S121
- S140 (police) (turn lights wiring harness, in breakout to c1010)
- S142 (police)
- S201
- S207
- S210
- Wig/wag jumper (police)
Lighting Control Module Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Lighting Control Module Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Anti-lock brakes system
- Anti-theft system
- Auto lamp on/off (delete for police)
- Auto lamp sens (delete for police)
- Batt1
- Batt2
- Batt3
- Batt4
- Batt5
- Batt6
- Brake shift interlock
- Brake switch
- C2145a
- C2145b
- C2145c
- C2145d
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Courtesy lamps
- Demand lighting
- Dome lamp sw
- Exterior lights system
- Flasher output
- Flasher power
- Fog lamp rly (mercury)
- Fog lamp sw (mercury)
- Fuse 10a
- Fuse 15a
- Fuse 7.5a
- G201 (right kick panel)
- Headlamp off
- Headlamps circuit
- Headlamps on
- Hi beam switch
- Horn rly ctrl
- Horns system
- Hot at all times
- Hot in run or acc
- Hot in run or start
- Interior lights system
- Key in ignition
- Left hi beam out
- Left lo beam
- Lighting control module (under center of dash)
- Logic batt
- Logic ground
- Panel dimmer
- Park/tail lamps
- Parklamps on/off
- Pnk
- Power distribution system
- Pwm dimming
- Rcm/chime request
- Right beam out
- Right lo beam
- Run/acc
- Run/start
- S210
- S276
- Scp +
- Scp -
- Shift interlock system
- Traction ctrl sw ind
- Trunk ajar
- Trunk lamp
- Wiper in (delete for police)
- Wiper/washer system
HORN
Horn Wiring Diagram, with Police for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Horn Wiring Diagram, with Police for Ford Crown Victoria Police Interceptor 2011:
- C133
- C298
- C494
- Fuse 2 a7 20a
- Fuse 4 c9 5a
- G108 (front of right fender)
- G220 (right kick panel)
- Horn (front center of engine compt)
- Hot in run or acc
- Hot w/ horn relay energized
- Nca
- Police glove box relay/fuse center (glove box)
- Police light bar relay/fuse center (front of luggage compt)
- R2 a5 relay
- S285
- Smart siren amplifier (luggage compt)
Horn Wiring Diagram, without Police for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Horn Wiring Diagram, without Police for Ford Crown Victoria Police Interceptor 2011:
- (front of right fender)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C2145b
- C217a
- C218a
- C218b
- C260
- Clock- spring (top of steering column)
- Ctrl
- Fuse 20a
- G108
- G201 (right kick panel)
- Horn (front center of engine compt)
- Horn relay
- Horn switch (near steering wheel)
- Hot at all times
- Lighting control module (under center of dash)
- S210
INSTRUMENT CLUSTER
Instrument Cluster Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Instrument Cluster Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (behind center of rear seat) g406
- (behind left kick panel)
- (body main wiring harness, near breakout to air suspension module) s259
- (front of left fender)
- (rear of left rear door) driver side rear door ajar switch
- (rear of right rear door) passenger side rear door ajar switch
- (right kick panel)
- (top rear of left front door) driver side front door ajar switch
- (top rear of right front door) passenger side front door ajar switch
- Air susp/fsil
- Batt
- Brake fluid level switch (on brake fluid reservoir)
- Brake ind
- C192
- C213
- C2145b ajar
- C248
- C260
- C408
- C423
- C501a
- C526a
- C526b
- C602a
- C602b
- C715a
- C715b
- C820a
- C820b
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Dr ajar sw
- Driver door module (bottom front of left front door)
- Except police
- Exterior lights system
- Fire suppression system module (fssm) (police) c3281a (under rear seat)
- Fsil
- Fuel level
- Fuel level rtn
- Fuel level sender (in fuel tank)
- Fuse 10a
- Fuse 7.5a
- G102
- G201
- G203 (right kick panel)
- G212
- Hot at all times
- Hot in run
- Hot in start or run
- Hs can+
- Hs can-
- Info
- Instrument cluster
- Interior lights system
- Left turn
- Lighting control module (under center of dash)
- Logic gnd
- Luggage compartment lid release solenoid (center rear of luggage compartment lid)
- Message center sw 1
- Message center sw 2
- Message center switch
- Nca
- Oil pressure
- Oil pressure switch (lower left side of engine, above oil filter)
- Park brake switch (behind left side of dash, on top of parking brake assembly)
- Pass ajar sw
- Police
- Power distribution system
- Pwr gnd
- Reset
- Right turn
- Ril
- Run
- Run/start
- S112
- S207
- S210
- S267
- S276
- S403
- Scp+
- Scp-
- Select
- Setup
- Suppression
- Swrtn
- W/o fire
- Washer level
- Wiper/washer system
INTERIOR LIGHTS
Courtesy Lamps Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Courtesy Lamps Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to air suspension module) s259
- (body main wiring harness, near breakout to g212) s330
- (bottom center of rear seat) g406
- (except police) (police)
- (interior lights wiring harness, near breakout to right vanity mirror lamp)
- (main wiring harness, near breakout to instrument cluster) s233
- (police)
- (rear of left rear door) driver side rear door ajar switch
- (rear of right rear door) passenger side rear door ajar switch
- (right kick panel)
- (right kick panel) g200
- (right kick panel) g201
- (top rear of left front door) driver side front door ajar switch
- (top rear of right front door) passenger side front door ajar switch
- Batt5
- C205b
- C211
- C213
- C2145a
- C2145b
- C2145c
- C2145d
- C260
- C275
- C408
- C423
- C501a
- C501b
- C526a
- C526b
- C602a
- C602b
- C715a
- C715b
- C820a
- C820b
- C913
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Courtesy lamps
- Crown victoria
- Demand lighting
- Dimmer
- Dome
- Dome lamp sw
- Dr door ajar sw
- Driver door module (bottom front of left front door)
- Emergency flasher relay block (center rear of luggage compt)
- Except police
- Fuse 15a
- G200
- G203 (right kick panel)
- G204 (right kick panel)
- Glove box lamp
- Grand marquis
- Hot at all times
- In breakout to left footwell courtesy light)
- Left footwell courtesy lamp
- Left vanity mirror lamp
- Lighting control module (under center of dash)
- Luggage compartment lamp
- Luggage compartment lid release solenoid (center rear of luggage compt lid)
- Main light switch
- Map reading lamps
- Panel dimmer
- Pass door ajar sw
- Police
- Police accessory connector (pigtail)
- Rear flasher relay
- Rear interior/ map lamps assembly (grand marquis)
- Right footwell courtesy lamp
- Right vanity mirror lamp
- S201
- S204
- S403
- S600
- S900
- S902
- S902 s600
- Scp+
- Scp-
- Stop reading lamp
- Trunk ajar
- Trunk lamp
Instrument Illumination Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Instrument Illumination Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (right kick panel) g201
- (right kick panel) g203
- (steering wheel control switch jumper harness, in breakout to steering wheel/speed control switch) s293
- (top of steering column)
- Adjustable pedal switch
- Audio control module (acm)
- Audio/ climate control switch
- Auto
- Base audio
- Batt1
- Batt5
- C205a
- C205b
- C213
- C2145a
- C2145b
- C2145c
- C218a
- C218b
- C228b
- C2330a
- C2330b
- C240
- C290a
- C294d
- C501a
- C501b
- Central junction box (cjb) (left of steering column)
- Climate control assembly
- Clockspring
- Computer data lines system
- Dimmer
- Dome
- Dome lamp sw
- Driver door module (bottom front of left front door)
- Driver side door lock switch
- Fuse 10a
- Fuse 15a
- Fuse 5a
- Fuse 7.5a
- G200 (right kick panel)
- G202 (right kick panel)
- G203 (right kick panel)
- G212 (behind left kick panel)
- Gnd
- Head
- Headlamps on
- Hot at all times
- Hot in acc or run
- Hot in start or run
- Hot w/ key in ignition
- Hvac module (eatc)
- Illum
- Key in ignition
- Keyless entry keypad
- Kick panel) g203
- Lighting control module (under center of dash)
- Logic batt
- Logic gnd
- Main light
- Main light switch
- Manual a/c
- Message center switch
- Off
- Panel dimmer
- Park
- Parklamps on/off
- Passenger side door lock switch
- Power illum
- Pwm
- Pwm dimming
- Rear window defrost switch
- Run/acc
- Run/st
- S201
- S207
- S210
- S229
- S254
- S276
- S287 (main wiring harness, near breakout to rear window defrost switch)
- S294
- S500
- S600
- Sanyo audio
- Scp+
- Scp-
- Steering wheel/ speed control switch
- Steering wheel/speed control switch
- Switch
- Traction control switch
- Variable volt dim
- Variable volt dim c228a
- W/ steering wheel audio/climate control switch
- W/eatc
- W/o steering wheel audio/climate control switch
POWER DISTRIBUTION
Power Distribution Wiring Diagram (1 of 5) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Distribution Wiring Diagram (1 of 5) for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to c248)
- (body main wiring harness, near breakout to g212) s234
- (front of right fender)
- (main wiring harness, near breakout to central junction box) s215
- (main wiring wiring harness, near breakout to c919)
- (right front of engine compt,
- (starter motor relay & battery ground wiring harness, near breakout to g101)
- 2 of 5)
- Abs module
- Acc
- Battery
- Battery junction box (bjb)
- Battery junction box (bjb) (right front of engine compt, near battery)
- Behind battery)
- Blower motor relay
- C102a
- C102b
- C175b
- C192
- C197a
- C202a
- C206
- C211
- C213
- C2131a
- C214
- C2145a
- C228a
- C237
- C248
- C260
- C294a
- C311
- C312
- C313
- C3281a
- C919
- Central junction box (cjb) (left of steering column)
- Circuit breaker f601 20a
- Climate control assembly
- Driver side front heated seat module
- Driver side front seat adjust switch
- Driver side lumbar adjust switch
- Engine cooling fan module
- Evap canister vent control solenoid
- Fire suppression manual switch
- Fire suppression system module (fssm)
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 30a
- Fuse 40a
- Fuse 50a
- Fuse 5a
- G100
- G101 (right front of engine)
- Generator
- Grand marquis
- Hvac module, eatc
- Ignition switch
- Instrument cluster (ic)
- Key-in ignition switch
- Left side spot lamp (taxi & police)
- Lighting control module
- Lock
- Luggage compartment lid release switch 2
- Manual climate control
- Multi- function switch
- Off
- Passenger side front heated seat module
- Passenger side front seat adjust switch
- Passenger side lumbar adjust switch
- Powertrain control module (pcm)
- Red
- Right side spot lamp (police)
- Run
- S137 (starter motor relay & battery ground wiring harness, near breakout to g101)
- S162
- S200 (main wiring harness, in breakout to c260)
- S224
- S242
- S365
- Start
- Starter motor
- Temperature blend door actuator
- To central junction box fuse 1 (diagram 2 of 5)
- To central junction box fuse 20 (diagram 2 of 5)
- To central junction box fuse 5 (diagram 5 of 5)
- To fuse 8 (diagram
- Vehicle dynamics module (vdm)
- W/ eatc
- W/ fire suppression
Power Distribution Wiring Diagram (2 of 5) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Distribution Wiring Diagram (2 of 5) for Ford Crown Victoria Police Interceptor 2011:
- (base)
- (body main wiring harness, near breakout to g200) s213
- (dash panel to headlight junction harness, near breakout to g106)
- (main wiring harness, in breakout to instrument cluster) s239
- (main wiring harness, near breakout to instrument cluster)
- (not used)
- (right front of engine compt, near battery) battery junction box (bjb)
- (sanyo)
- Anti- lock brake system module
- Anti-lock brake system module
- Audio control module (acm)
- C139
- C2145a
- C2145b
- C237
- C240
- C260
- C290a
- C299
- C310a
- C310b
- C312
- C501b
- Central junction box (cjb) (left of steering column)
- Digital transmission range (dtr) sensor
- Digital transmission range sensor
- Driver door module
- Exterior lights system
- From battery junction box (bjb) ignition coils relay (diagram 2 of 5)
- From fuse 2 (diagram 1 of 5)
- From ignition switch (diagram 1 of 5)
- Fuel pump relay
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 30a
- Fuse 40a
- Fuse 5a
- Fuse 7.5a
- Ignition coils relay
- Instrument cluster (ic)
- Lighting control module
- Occupant classification sensor module
- Passenger air bag deactivation (pad) indicator
- Passive anti-theft transceiver
- Pcm power diode
- Pcm power relay
- Power point
- Rear window defrost relay
- Restraints control module
- S160
- S190 (dash panel to headlight harness, near breakout to battery junction box)
- S276
- S515 (body main wiring harness, near breakout
- Starter relay
- To battery junction box (bjb) fuse 5 (diagram 3 of 5)
- To central junction box (cjb) fuse 24 (diagram 2 of 5)
- To driver's door module)
- Traction control switch
- Transmission control switch
- W/ crown police
Power Distribution Wiring Diagram (3 of 5) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Distribution Wiring Diagram (3 of 5) for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, in breakout to c248) s246
- (body main wiring harness, near breakout to g200) s220
- (dash panel to headlight junction wiring harness, in breakout to c214)
- (diagram 3 of 5)
- (not used)
- (power distribution wiring harness, in breakout to police light bar relay/fuse center) s462
- (right front of engine compt, near battery) battery junction box (bjb)
- (w/o police light bar relay/fuse center)
- (w/o police) (w/ police)
- A/c clutch relay
- Battery junction box (bjb) (right front of engine compt, near battery)
- Blower motor relay
- Brake pedal position (bpp) switch
- C1 relay 4
- C2 relay 4
- C2131a
- C214
- C248
- C268
- C275
- C3 relay 4
- C311
- C313
- C4 relay 4
- C406
- C431
- C432
- C466a
- C5 relay 4
- C6 relay 4
- C7 relay 4
- C8 relay 4
- Driver side front heated seat module
- Emergency flasher relay 1
- Emergency flasher relay 2
- Emergency flasher relay block (w/ police) (center rear of luggage compartment)
- Fog lamp relay
- From battery junction box (bjb) fuse 16 c
- From battery junction box b (bjb) fuse 13 (diagram 2 of 5)
- Fuse 10a
- Fuse 15a
- Fuse 20a
- Fuse 20a 25a
- Fuse 40a
- Fuse 50a
- Horn relay
- Near breakout to c405) s433
- Passenger side front heated seat module
- Police
- Police accessory connector (pigtail)
- Police light bar relay/fuse center (front of luggage compartment)
- Rear flasher relay
- Red
- S281
- S469 (power distribution wiring harness, in breakout to police light bar relay/fuse center)
- Speed control deactivator switch
- Subwoofer amplifier
- To battery junction box (bjb) fuse 103 (diagram 4 of 5)
- To battery junction box (bjb) fuse 113 (diagram 3 of 5)
- To rear police auxiliary junction box (diagram 5 of 5)
- Vehicle dynamics module (vdm)
- W/ crown police
- W/ police
- W/o
- Wiring harness, near breakout to center console)
Power Distribution Wiring Diagram (4 of 5) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Distribution Wiring Diagram (4 of 5) for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to g212) s254
- (w/o police) (w/ police)
- Adjustable pedal switch
- Audio control module (acm)
- Autolamp sensor
- Base
- Battery junction box (bjb) (right front of engine compt, near battery)
- C202a
- C211
- C2145a
- C2145c
- C228a
- C240
- C260
- C275
- C290a
- C299
- C501b
- Central junction box (cjb) (left of steering column)
- Data link connector (dlc)
- Driver door module
- Electronic automatic temperature control (eatc) module
- Except police
- Exterior rear view mirror switch
- From battery junction box d (bjb) fuse 117 (diagram 3 of 5)
- Front cigar lighter
- Fuse 10a
- Fuse 15a
- Fuse 15a 20a
- Fuse 20a
- Fuse 30a
- Fuse 50a
- Fuse 7.5a
- Instrument cluster (ic)
- Keyless entry keypad
- Lighting control module
- Luggage compartment lid release switch 1
- Multi-function switch
- Police accessory connector (pigtail)
- S244 (main wiring harness, near breakout to right footwell courtesy light)
- S426 (emergency jumper wiring harness, in breakout for strobe/light bar control switch)
- Sanyo
- Tan
- Taxi roof lamp switch
- To battery junction box (bjb) fuse 118 (diagram 5 of 5)
- To central junction box fuse 23 (diagram 5 of 5)
- W/ police
- Windshield wiper motor
Power Distribution Wiring Diagram (5 of 5) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Distribution Wiring Diagram (5 of 5) for Ford Crown Victoria Police Interceptor 2011:
- (base)
- (body main wiring harness, near breakout to c248) s229
- (dash panel to headlight junction wiring harness, near breakout to c275) s282
- (emergency jumper wiring harness, near breakout for c422) s470
- (main wiring harness, near breakout to central junction box)
- (police if equipped)
- (power distribution wiring harness, in breakout to police trunk relay/fuse center)
- (sanyo)
- 10a
- Accessory relay
- Air suspension compressor relay
- Antenna module
- Audio control module (acm)
- Auto-dimming interior mirror
- B1 fuse 4
- B1 relay 4
- B2 fuse 4
- B2 relay 4
- B3 fuse 4
- B4 relay 4
- B5 relay 4
- Battery junction box (bjb) (right front of engine compartment, behind battery)
- Battery junction box (bjb) (right front of engine compt, near battery)
- C202c
- C211
- C213
- C2145b
- C2145c
- C2145d
- C240
- C260
- C290a
- C402b
- C4170a
- C422
- C504b
- Central junction box (cjb) (left of steering column)
- Circuit breaker f602 20a
- Driver side door lock switch
- Driver side seat heater switch
- From battery junction box (bjb) s244 (diagram 4 of 5)
- From battery junction box e (bjb) fuse 111 (diagram 4 of 5)
- From battery junction box n (bjb) fuse 115 (diagram 3 of 5)
- From ignition switch (diagram 1 of 5)
- Fuse 10a
- Fuse 15a
- Fuse 30a (w/o police) 40a (w/ police)
- Fuse 50a
- Fuse 7.5a
- G203 (right kick panel)
- Lighting control module
- Luggage compartment lid release switch 1
- Luggage compartment lid release switch 3
- Master window adjust switch
- Multi-function switch
- Passenger side door lock switch
- Passenger side seat heater switch
- Pnk
- Police power relay
- Police trunk relay/fuse center (front of luggage compartment)
- Rear police auxiliary junction box (w/ police)
- Red
- Relay/fuse center)
- S207
- S279
- S474
- S478
- S502 (body main wiring harness, near breakout to exterior rearview mirror switch)
- W/ crown police
- W/ police
- Windshield wiper motor
POWER DOOR LOCKS
Power Door Locks Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Door Locks Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to left front door lock actuator) s520
- All doors lock
- Antenna module (base of right "c" pillar)
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C248
- C501a
- C501b
- C501c
- C526a
- C526b
- C602a
- C602b
- C715a
- C715b
- C820a
- C820b
- Computer data lines system
- Decklid rel in
- Door lock
- Door unlock
- Dr door ajar sw
- Dr door unlk
- Driver door module (bottom front of left front door)
- Driver side front door ajar switch (top rear of left front door)
- Driver side rear door ajar switch (rear of left rear door)
- Fuse 20a
- G201 (right kick panel)
- G212 (behind left kick panel)
- G420 (right "c" pillar)
- Hot at all times
- Keypad illum
- Keypad input a
- Keypad input b
- Keypad input c
- Logic bat
- Logic gnd
- Nca
- Pass door unlk
- Pass dr ajar sw
- Passenger side front door ajar switch (top rear of right front door)
- Passenger side rear door ajar switch (rear of right rear door)
- Pwr gnd
- Red
- Red/
- Rf ask/fsk sel
- Rf data
- Rf recur enable
- Rf recvr gnd
- Rf recvr pwr
- S217
- S500
- S515
- Scp+
- Scp-
- Vbatt
- Wiring harness, near breakout to air suspension module) s259
Power Door Locks Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Door Locks Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (behind left kick panel)
- (body main wiring harness, near breakout to exterior rearview mirror switch)
- (right kick panel) g200
- 1/2
- 3/4
- 5/6
- 7/8
- 9/0
- C213
- C2145a
- C2145b
- C423
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Driver side door lock switch
- Exterior lights system
- Fuse 7.5a
- G212
- G212 (behind left kick panel)
- G406 (bottom center of rear seat)
- Horn
- Horns system
- Hot at all times
- Hot in run or acc
- Illumination
- Keyless entry keypad
- Left front door lock actuator (rear of left front door)
- Left rear door lock actuator (rear of left rear door)
- Lighting control module (under center of dash)
- Lock
- Luggage compartment lid release solenoid (center rear of luggage compt lid)
- Luggage compartment lid release switch 1
- Passenger side door lock actuator (rear of right front door)
- Passenger side door lock switch
- Police
- Power distribution system
- Right rear door lock actuator (rear of right rear door)
- S229 (body main wiring harness, near breakout to c248)
- S254
- S260 (body main wiring harness, near breakout to g212)
- S261 (body main wiring harness, near breakout to g212)
- S403
- S500
- S503 (body main wiring harness, near breakout to driver's door module)
- S510
- S600
- Scp+
- Scp-
- Trunk ajar
- Unlock
POWER MIRRORS
Electrochromic Mirror Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Electrochromic Mirror Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (body main
- (right kick panel)
- Auto-dimming interior mirror
- C139
- C139 e
- C260
- C408
- C423
- C913
- Central junction box (cjb) (left of steering column)
- Digital transmission range (dtr) sensor (left side of transmission)
- Door actuator)
- Exterior
- Fuse 10a
- Fuse 7.5a
- G200
- Ground
- Hot in run or acc
- Hot in run or start
- Lights system
- Near breakout to temperature blend
- Police
- Pwr
- Reverse
- S229
- S248
- S600
- Wiring harness,
Power Mirrors Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Mirrors Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Central junction box (cjb) (left of steering column)
- Defogger system
- Down
- Exterior rear view mirror switch
- Fuse 7.5a
- G212 (behind left kick panel)
- Hot at all times
- Left
- Left exterior rear view mirror
- Left mirror select
- Left/ right
- Right
- Right exterior rear view mirror
- Right mirror select
- S250 (main body wiring harness, near breakout to g212)
- S254
- S500
- Up/ down m
POWER SEATS
Adjustable Pedal Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Adjustable Pedal Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (main wiring harness, near breakout to electronic automatic temperature control module) s204
- Adjustable pedal motor (below left side of dash)
- Adjustable pedal switch
- C211
- Central junction box (cjb) (left of steering column)
- Fuse 15a
- Fwd
- G203 (right kick panel)
- G204 (right kick panel)
- Hot at all times
- Interior lights system
- Red
- Rwd
- S207 (main wiring harness, near breakout to rear window defrost switch)
Driver Power Seat Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Driver Power Seat Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (behind left kick panel) g213
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C311
- Circuit breaker f601 20a
- Driver seat recliner motor
- Driver side front seat adjust switch
- Front up/down
- Fwd
- Fwd/back
- Hot at all times
- Left power seat motor assembly (driver's seat)
- Rear up/down
- Recline fwd/back
- Rwd
- S242
Heated Seats Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Heated Seats Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Backlighting
- Batt
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C311
- C312
- C313
- C334
- C364
- C510
- C610
- Central junction box (cjb) (under left side of dash)
- Driver side front heated seat module (driver seat)
- Driver side seat heater switch
- Fuse 10a
- Fuse 20a
- Fuse 7.5a
- G200 (right kick panel)
- G212 (behind left kick panel)
- Gnd
- High ind
- High/off
- Hot at all times
- Hot in run
- Hot in run or acc
- Htr feed
- Htr rtn
- Ign/run
- Left front seat back heater
- Left front seat cushion heater (driver's seat)
- Low
- Low ind
- Low/off
- Nca
- Ntc rtn
- Ntc sense
- Passenger side front heated seat module (under passenger seat)
- Passenger side seat heater switch
- Red
- Right front seat back heater
- Right front seat cushion heater (under right front seat)
- S220
- S229
- S315
- S320
- S365
- S500
- S600
Passenger Power Seat Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Passenger Power Seat Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (right kick panel)
- Battery junction box (bjb) (right front of engine compt, near battery)
- C312
- Circuit breaker f601 20a
- Front up/down
- Fwd
- Fwd/back
- G200
- Hot at all times
- Passenger seat recliner motor
- Passenger side front seat adjust switch
- Rear up/down
- Recline fwd/back
- Right power seat motor assembly (front passenger's seat)
- Rwd
- S242
- S600
POWER WINDOWS
Power Windows Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Power Windows Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to air suspension module)
- (police)
- Accessory relay
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C260
- C340
- C504a
- C504b
- C700
- C800
- Central junction box (cjb) (left of steering column)
- Circuit breaker 20a
- Driver side front power window motor (left front door)
- Exp
- G213 (behind left kick panel)
- Gnd
- Hot at all times
- Left rear power window motor (rear of left rear door)
- Left rear window adjust switch
- Lockout
- Master window adjust switch
- Passenger side front power window motor (right front door)
- Police
- Relay
- Right rear power window motor (rear of right rear door)
- Right rear window adjust switch
- Right side front power window switch
- S303 s264 (except police) (body main wiring harness, near breakout to restraints control module)
- S502 (police) (body main wiring harness, near breakout to exterior rearview mirror switch)
- Up sense
- Up shunt
RADIO
Base Radio Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Base Radio Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (right kick panel) g203
- Amp gnd
- Ant pwr
- Antenna module (base of right "c" pillar)
- Audio unit
- Batt +
- C213
- C237
- C402a
- C402b
- Central junction box (cjb) (left of steering column)
- Def pwr
- Defogger system
- Fuse 15a
- Fuse 5a
- Fuse 7.5a
- G202 (right kick panel)
- Hot at all times
- Hot in run or acc
- Hot in start
- Ill gnd
- Interior lights system
- L front spkr (+)
- L front spkr (-)
- L rear spkr (+)
- L rear spkr (-)
- Left front speaker
- Left rear speaker
- Pair wires
- Power distribution system
- Pwm dimming
- R front spkr (+)
- R front spkr (-)
- R rear spkr (+)
- R rear spkr (-)
- Rad gnd
- Right front speaker
- Right rear speaker
- Run/acc
- S207
- S279
- Start
- Twisted
Premium Radio Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Premium Radio Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (steering wheel control switch jumper harness,
- Ant pwr
- Antenna module (base of right "c" pillar)
- Audio unit
- Audio/climate control switch
- Aux out1+
- Aux out1-
- Auxout 1 enable
- Auxout shield
- Batt+
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C213
- C218a
- C218b
- C228b
- C237
- C248
- C290a
- C290c
- C402a
- C402b
- C432
- C466a
- C466b
- Central junction box (cjb) (left of steering column)
- Clock spring
- Def pwr
- Defogger system
- Engine controls system
- Fuse 15a
- Fuse 20a
- Fuse 5a
- Fuse 7.5a
- G202 (right kick panel)
- G203 (right kick panel)
- G407 (behind left rear seat)
- Gnd
- Hot at all times
- Hot in run and acc
- Hot in start
- Hvac module, eatc
- In breakout to steering wheel/speed control switch)
- Input+
- Input-
- Interior lights system
- Left front speaker
- Left rear speaker
- Lf+
- Lf-
- Lr+
- Lr-
- Mute
- Nca
- Next
- Pair wires
- Power distribution system
- Pwm dimming
- Pwr
- Pwr gnd
- Red
- Remote
- Rest
- Rf+
- Rf-
- Right front speaker
- Right rear speaker
- Rr+
- Rr-
- Run/acc
- S201
- S229 (body main wiring harness, near breakout to c248)
- S279
- S294
- Spkr+
- Spkr-
- Start
- Subwoofer amplifier
- Subwoofer speaker
- Temp+
- Temp-
- Twisted
- Vehicle speed sig
- Vol+
- Vol-
SHIFT INTERLOCK
Shift Interlock Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Shift Interlock Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Anti-lock brakes system
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Brake pedal position (bpp) switch (top of brake pedal support)
- Brake shift interlock (steering column)
- Brake sw
- Bsi
- C139
- C192
- C211
- C2145a
- C2145b
- C2145c
- C260
- Central junction box (cjb) (left of steering column)
- Digital transmission range (dtr) sensor (left side of transmission)
- Fuse 10a
- Fuse 20a
- Fuse 30a
- Fuse 5a
- Fuse 7.5a
- G201 (right kick panel)
- G204 (right kick panel)
- G212 (behind left kick panel)
- Hot at all times
- Hot in run or start
- Hot in start
- Ignition switch
- Key in ignition
- Key-in ignition
- Lighting control module (lcm) (under center of dash)
- Logic gnd
- Red
- Run/st
- S200
- S204
- S210
- S246
- S267
- S276
- Starter relay
STARTING/CHARGING
Charging Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Charging Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- Battery
- Battery junction box (bjb) (right front of engine compartment, behind battery)
- C102a
- C102b
- C139
- C175b
- C175e
- C192
- C197a
- Charging indicator
- Computer data lines system
- Fuse 15a
- G100 (front of right fender)
- G101 (right front of engine)
- Generator
- Gen_com
- Gen_mon
- Hs can+
- Hs can-
- Instrument cluster (ic)
- Powertrain control module (pcm) (left rear of engine compt)
- Red
- S137
- S162
- Starter motor
Starting Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Starting Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (left rear of
- Acc
- Battery
- Battery junction box (bjb) (right front of engine compartment,
- Behind battery)
- C139
- C146
- C175b
- C192
- C197a
- C197b
- C260
- Central junction box (cjb) (left of steering column)
- Charging circuit
- Control
- Digital transmission range (dtr) sensor (left side of transmission)
- Engine compt)
- Fuse 10a
- Fuse 30a
- G100 (front of right fender)
- G101 (right front of engine)
- Ignition switch
- Lock
- Module (pcm)
- Off
- Powertrain
- Red
- Run
- S200
- Smc
- Start
- Starter motor
- Starter relay
SUPPLEMENTAL RESTRAINTS
Supplemental Restraints Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Supplemental Restraints Wiring Diagram (1 of 2) for Ford Crown Victoria Police Interceptor 2011:
- (body main harness, near breakout to restraints control module)
- (main body wiring harness, near breakout to c919)
- (main wiring harness, in breakout to instrument cluster) s239
- (right kick panel)
- C175b
- C237
- C248
- C260
- C310a
- C310b
- C311
- C312
- C315
- C316
- Central junction box (cjb) (left of steering column)
- Chime req
- Computer data lines system
- Driver safety belt retractor pretensioner (base of left ``b" pillar)
- Driver side safety belt sensor
- Driver side seat position sensor (below driver seat)
- Feed
- Fuse 10a
- G201
- G201 (right kick panel)
- Hot in run or start
- Iso
- Left side impact sensor (w/ side air bag) (base of left "b" pillar)
- Logic gnd
- Nca
- Ocs can hi
- Ocs can low
- Pad ind
- Passenger air bag module (right side of dash)
- Passenger safety belt retractor pretensioner (base of right ``b" pillar)
- Pin shorting bars engaged when module connector is disconnected from harness shorting bars are connected between pins: 1-2, 21-22 conn. c310b
- Powertrain control module (pcm) (left rear of engine compt)
- Rdi
- Red
- Restraints control module (below center of dash)
- Return
- Right front impact severity sensor (right front of engine compartment)
- Right side impact sensor (w/ side air bag) (base of right "b" pillar)
- Ril
- Run start
- S213 (main body wiring harness, near breakout to g200)
- S217
- S301 (power seats harness, in breakout to c311)
- S305
- Shorting bar
- Stage 1
- Stage 2
- Vid 1
- Vid 2
Supplemental Restraints Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Supplemental Restraints Wiring Diagram (2 of 2) for Ford Crown Victoria Police Interceptor 2011:
- Bts
- Bts rtn
- Bts vref
- C2145a
- C218a
- C312
- Central junction box (cjb) (left of steering column)
- Clock- spring (top of steering column)
- Driver air bag module (in steering wheel)
- Fuse 10a
- G201 (right kick panel)
- Gnd
- Ground
- Hot in run or start
- Hs safety can
- Hs safety can -
- Instrument cluster
- Left front impact severity sensor (left front of engine compartment)
- Left side air bag module (resistor w/o side air bags) (driver's seat)
- Lighting control module (under center of dash)
- Nca
- Occupant classification sensor (ocs) (passenger seat)
- Occupant classification system module (under passenger seat)
- Passenger air bag deactivation (pad) indicator
- Passenger side safety belt sensor
- Pwr
- Rcm/chime request
- Red
- Right side air bag module (resistor w/o side air bags) (passenger's seat)
- Ril
- Run/start
- S217
- S276
- Shorting bar
- Sig
- Tan/ red
- Tan/red
- V ign
- Vout
- Vref
TRANSMISSION
Transmission Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Transmission Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (dash panel to headlight junction harness, near breakout to battery junction box (bjb))
- (engine control sensor & fuel charge wiring harness, near breakout to pcm)
- (left side of transmission) digital transmission range (dtr) sensor
- 4r70e transmission
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C175b
- C175e
- C175t
- C192
- C260
- C261
- Case gnd
- Central junction box (cjb) (left of steering column)
- Computer data lines system
- Electronic throttle control (etc) motor (right rear of engine)
- Engine controls system
- Epc
- Etcref
- Etcrtn
- Feps
- Fuel pump relay
- Fuse 10a
- Fuse 15a
- Fuse 30a
- G106 (left rear of engine compt)
- G107 (left rear of engine compt)
- G109 (front of right fender)
- Hot at all times
- Hot in run or start
- Iat
- Ignition coils relay
- Maf
- Mafrtn
- Mass air flow/intake air temperature (maf/iat) sensor (behind air cleaner assembly)
- Oss
- Output shaft speed (oss) sensor (left side of transmission)
- Pcm power diode
- Pcm power relay
- Power distribution system
- Powertrain control module (pcm) (left rear of engine compt)
- Pwr gnd
- Red
- S118
- S119
- S121
- S146
- S147
- S276
- Sigrtn1
- Ssa
- Ssb
- Tacm+
- Tacm-
- Tcc
- Tcs
- Tft
- Throttle position sensor (on throttle body)
- Tp1-ns
- Tp2-ps
- Tr1
- Tr2
- Tr3a
- Tr4
- Transmission control switch (steering column)
- Tss
- Turbine shaft speed sensor (left side of transmission)
- Vpwr
TRUNK, TAILGATE, FUEL DOOR
Trunk Release Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Trunk Release Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- C211
- C213
- C423
- Central junction box (cjb) (left of steering column)
- Decklid
- Decklid release sol c501b
- Demand lighting c2145c
- Driver door module (bottom front of left front door)
- Fuse 7.5a
- G406 (bottom center of rear seat)
- Hot at all times
- Interior lights system
- Lighting control module (under center of dash)
- Luggage compartment lamp
- Luggage compartment lid release solenoid (center rear of luggage compt lid)
- Luggage compartment lid release switch 1
- Release c501a input
- S226 (main wiring harness, in breakout to left footwell courtesy light)
- S254
- S403
- Trunk ajar c2145b
- Trunk lamp c2145d
- Wiring harness, near breakout to g212) s330
Trunk Release Wiring Diagram, Police Option for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Trunk Release Wiring Diagram, Police Option for Ford Crown Victoria Police Interceptor 2011:
- (if equipped)
- (left of steering column)
- Accessory relay
- Battery junction box (bjb) (right front of engine compt, behind battery)
- Breakout to left footwell courtesy light)
- C211
- C213
- C260
- C408
- Central junction box (cjb)
- Circuit breaker 20a
- Decklid
- Driver door module (ddm) (w/ keyless entry) (bottom front of left front door)
- Fuse 7.5a
- G109 (front of right fender)
- G406 (bottom center of rear seat)
- Hot at all times
- Hot in run or acc
- Lighting control module (under center of dash)
- Luggage compartment lid release solenoid (center rear of luggage compt lid)
- Luggage compartment lid release switch 1 (if equipped)
- Luggage compartment lid release switch 2
- Luggage compartment lid release switch 3
- Power distribution system
- Release c501b sol
- S121
- S242
- S251 (main wiring harness, near breakout to rear window defrost switch)
- S279
- S403
- S502 (body main wiring harness, near breakout to exterior rearview mirror switch)
- Trunk ajar c2145b
- Used)
WARNING SYSTEMS
Warning Systems Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Warning Systems Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (body main wiring harness, near breakout to air suspension module) s259
- (right kick panel) g203
- Anti-lock brake system (abs) module (left front of engine compt)
- Auto
- Batt
- Battery junction box (bjb) (right side of engine compt, behind battery)
- Brake fluid level switch (on brake fluid reservoir)
- Brk ind
- C175b
- C213
- C2145a
- C2145b
- C248
- C260
- C310a
- C310b
- C311
- C312
- C423
- C526a
- C602a
- C715a
- C820a
- Central junction box (cjb) (under left side of dash)
- Chime req
- Computer data lines system
- Driver door module (bottom front of left front door)
- Driver dr ajar sw c501a
- Driver side front door ajar switch (top rear of left front door) c526b
- Driver side rear door ajar switch (rear of left rear door) c715b
- Driver side safety belt sensor (driver's seat)
- Drv bckl sw in
- Fuse 10a
- Fuse 30a
- Fuse 5a
- Fuse 7.5a
- G102 (front of left fender)
- G201 (right kick panel)
- G203 (right kick panel)
- G212 (behind left kick panel)
- G406 (bottom center of rear seat)
- Hdlp off
- Hdlp on park lamps on/off hdlp on/off (delete for police)
- Head
- Hot at all times
- Hot in run
- Hot in run or start
- Hs can +
- Hs can -
- Ignition switch
- Instrument cluster (ic)
- Interior lights system
- Iso 9141
- Key in ign
- Key in ignition switch
- Lighting control module (under center of dash)
- Luggage compartment lid release solenoid (center rear of luggage compartment lid)
- Main light switch
- Off
- Park
- Park brake switch (behind left side of dash, on top of parking brake assembly)
- Pass bckl sw
- Pass dr ajar sw c501b
- Passenger side front door ajar switch (top rear of right front door) c602b
- Passenger side rear door ajar switch (rear of right rear door) c820b
- Passenger side safety belt sensor (passenger's seat)
- Power distribution system
- Powertrain control module (pcm) (left rear of engine compt)
- Pwr gnd
- Rcm/chime request
- Rdi
- Restraints control module (below center of dash)
- Ril
- Run
- Run/st
- S112
- S200
- S201
- S207
- S217
- S267
- S276
- S301 (power seats harness, in breakout to c311) c311
- S305 (body main wiring harness, near breakout to restraints control module (rcm))
- S403
- Scp +
- Scp -
- Scp+
- Scp-
- Strkrtn
- Trunk ajar
WIPER/WASHER
Wiper/Washer Wiring Diagram for Ford Crown Victoria Police Interceptor 2011
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO 获取访问所有汽车的接线图List of elements for Wiper/Washer Wiring Diagram for Ford Crown Victoria Police Interceptor 2011:
- (front of left fender)
- (not used)
- 4. int2 5. int3 6. int4 7. int5 8. low 9. high
- Batt
- Battery junction box (bjb) (right front of engine compt, behind battery)
- C202b
- C2145d
- C260
- Central junction box (cjb) (left of steering column)
- Electronics
- Front washer relay
- Fuse 10a
- Fuse 30a
- Fuse 7.5a
- G102
- G102 (front of left fender)
- G203 (right kick panel)
- Hi/lo speed relay
- High
- Hot at all times
- Hot in run or acc
- Instrument cluster
- Lighting control module (except police) (under center of dash)
- Low
- Multi-function switch 1. not used 2. off 3. int1
- Park
- Power distribution system
- Red
- Run
- Run/ park relay
- S112
- S201
- Wash switch
- Washer fluid level switch (washer fluid reservoir)
- Washer level
- Windshield washer pump motor (washer fluid reservoir)
- Windshield wiper motor (left rear of engine compt)
- Wiper input