ANTI-LOCK BRAKES – Dodge Pickup R2500 1997 – SYSTEM WIRING DIAGRAMS

ANTI-LOCK BRAKES

All-Wheel ABS Wiring Diagram for Dodge Pickup R2500 1997

List of elements for All-Wheel ABS Wiring Diagram for Dodge Pickup R2500 1997:

• (behind knee bolster) joint connector c
• (engine harn, in breakout to abs mod) s158
• (engine harn, in breakout to abs module) s208
• (engine harn, near breakout to abs module) s109
• (in breakout to hcu) s112
• (right fender side shield)
• (top of rear differential) rear wheels sensor
• 4 x 4 ind
• 4wd switch input
• 4x4 switch (on front of frame)
• 87a
• A20
• Abs 2-way power feed (left fender side shield)
• Abs lamp relay ctrl
• Abs pump relay (in power distribution center)
• Abs pump relay ctrl
• Abs warn ind
• Abs warning ind ctrl
• Abs warning lamp relay (in power distribution center)
• Acc
• Anti-lock brake system control module (left fender side shield)
• B113
• B114
• B116
• B120
• B18
• B19
• B243
• B245
• B248
• B249
• B252
• B254
• B47
• B60
• Brake warn indic.
• Brake warning ind
• Brake warning switch (on left frame rail)
• D11
• D12
• Data link connector (left bottom of i/p)
• Data link input
• Data link output
• Dump sol
• Engine controls (pcm)
• Fuse 20a
• Fuse 40a
• Fuse block
• G100 (left fender shield)
• G100 (left fender side shield)
• G101
• G104 (fender shield)
• G107
• G19
• G206 (i/p right center support)
• Ground
• Ground joint (near pdc)
• Hot at all times
• Hot in run
• Hydraulic control unit (rear of abs pump)
• Ignition
• Ignition switch
• Instrument cluster
• Isolate sol
• Left front reset
• Left front wheel sensor
• Left isolation and dump solenoids
• Lt frnt isolate sol ctrl
• Lt front dump ctrl
• Lt front wheel sensor
• Off
• Power distribution center
• Pump motor ctrl
• Pump motor feed
• Rear dump sol ctrl
• Rear isolate sol ctrl
• Rear reset
• Rear wheels sensor
• Red
• Reset sw
• Right front reset
• Right front wheel sensor
• Rt frnt isolate sol ctrl
• Rt front dump sol ctrl
• Rt front wheel sensor
• Rt isolation and dump solenoids
• Run
• Rwal valve (below master cylinder)
• S103
• S105 (engine harn, in breakout to horn)
• S108
• S110 (in breakout to abs mod)
• S208
• Start
• Stop lamp switch
• Stop lamp switch (on brake pedal bracket)
• V40
• Vacuum sensor (diesel only) (left fender side shield)

Rear Wheel ABS Wiring Diagram for Dodge Pickup R2500 1997

List of elements for Rear Wheel ABS Wiring Diagram for Dodge Pickup R2500 1997:

• (left bottom of i/p) data link connector
• 4wd indicator
• 4wd switch input
• 4x4 switch (on front of frame)
• A20
• Abs warning ind ctrl
• Abs warning lamp
• Acc
• B101
• B108
• B111
• B112
• B113
• B114
• Brake sw input
• Brake warning
• Brake warning lamp
• Brake warning switch (left side frame rail)
• Diagnostic signal
• Diesel
• Dump sol
• F32
• Fuse 20a
• Fuse block
• Fused b(+)
• Fused ign (run)
• G100 (left fender side shield)
• G104 (left fender shield)
• G107
• G11
• G19
• G206 (i/p right center support)
• Gasoline
• Ground
• Ground joint (near pdc)
• Hot at all times
• Hot in run
• Ignition switch
• Instrument cluster
• Isolate sol
• Joint connector b (near rear of fuse block)
• Joint connector c (behind knee bolster)
• Off
• Park brake indic.
• Park brake input
• Park brake switch (on brake bracket)
• Rear wheel anti-lock control module (center of i/p)
• Rear wheel sensor (+)
• Rear wheel sensor (-)
• Rear wheel speed sensor (left frame rail, near fuel tank)
• Reset
• Reset sw
• Run
• Rwal dump solenoid
• Rwal hydraulic valve (below master cylinder)
• Rwal isolate solenoid
• S103
• S109 (engine harn, near breakout to abs module)
• S208
• Start
• Stop lamp switch (brake pedal bracket)
• V40
• Vacuum sensor (diesel only) (left fender side shield)