Diagram sections — 23 (39 total)
ANTI-LOCK BRAKES COMPUTER DATA LINES CRUISE CONTROL DEFOGGERS ENGINE PERFORMANCE EXTERIOR LIGHTS GROUND DISTRIBUTION HEADLIGHTS HORN INSTRUMENT CLUSTER INTERIOR LIGHTS PASSIVE RESTRAINTS POWER DISTRIBUTION POWER DOOR LOCKS POWER WINDOWS RADIO SHIFT INTERLOCKS STARTING/CHARGING SUPPLEMENTAL RESTRAINTS TRANSMISSION TRUNK, TAILGATE, FUEL DOOR WARNING SYSTEMS WIPER/WASHER
ANTI-LOCK BRAKES
COMPUTER DATA LINES Data Link Connector Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Data Link Connector Wiring Diagram for Chevrolet Beretta Z26 1994: 13 (vin a) (vin m) (vin m) (vin a & 4) A11 C2 c3 D12 Data link connector (left lower hush panel) Diagnostic energy reserve module (behind right front kick panel) Electronic brake control module (rear of engine compatrment, center of dash panel) G 130 (left front of engine on transmission stud) g 115 (center rear of engine on transmission stud under exhaust) Powertrain control module (right upper i/p, attached to bracket) Serial data line Tan
CRUISE CONTROL Cruise Control Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Cruise Control Wiring Diagram for Chevrolet Beretta Z26 1994: 75 #14 (behind right side of inst. (behind upper right side (left rear of engine (left rear of engine on top of (lower right front of transaxle (on brake pedal (on clutch pedal support) (rear of engine compt (right rear of engine on transaxle) (right side of engine on top (vin 4) (vin 4/a/t) (vin a) (vin m & 4) (vin m) 15a 4000 pulses/mile A/t Alarm module Assembly Block Brake input Brake sw Center of dash panel) Compartment on trans. Compartment, above Cruise control clutch sw Cruise control module Cruise control servo Cruise engage output Cruise engaged input D13 D14 Engine control module (ecm) Fuse G101 Ground Hot in accy or run Instrument cluster L4 vin 4 & a M/t Multi/function Multi/function lever Of inst. panel, attached Of transaxle) Off On input On output shaft housing) Panel, above glove box) Position R/a Red Resume/accel input Sensor Servo Servo postn input Set Set/coast input Starter) Stud) Support) Tan To a bracket) Transaxle) V6 vin m Vacuum valve Vacuum valve ctrl Vehicle speed sensor Vent valve Vent valve ctrl Vss input Vss input/hi Vss input/lo Wiper motor
DEFOGGERS Defogger Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Defogger Wiring Diagram for Chevrolet Beretta Z26 1994: 19 (vin 4) (vin a) (vin m) Circuit breaker 15 30 a Fuse 9 20 a Fuse block: i/p G104 (left rear of engine compartment, above starter) g104 (left rear of engine compartment, on transaxle stud) g114 (left rear of engine on transaxle stud) G312 (behind left rear seat) Hot at all times Hot in run, bulb test or start Interior lights system Nca On indicator Panel lamp Pnk Rear defogger Rear defogger control & washer/ wiper switch Rear defogger switch Solid state timer
ENGINE PERFORMANCE
2.2L 2.2L (VIN 4), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Beretta Z26 1994 List of elements for 2.2L (VIN 4), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Beretta Z26 1994: 74 5 volts ref A/c press signal A/c request A/c sensor (right front of engine compt) A10 A11 A12 B10 B11 B12 Battery ref C10 C11 C12 C13 C14 C15 C16 Conn c1 Conn c2 Crank sens output Crank sensor b+ feed Crank sensor grd Crank shaft position sensor (lower right side of engine) D10 D11 D12 D13 D14 D15 D16 Ect sensor in Engine control module (ecm) (behind right side of i/p, near shroud) Engine coolant temperature sensor (left side of engine) Fuel injector #1 Fuel injector #2 Fuel injector #3 Fuel injector #4 Fuel pump relay ctrl Fuse 20a Fuse block Fusible link (20 ga-gray) G117 right rear of engine, on transaxle stud) Ground Heater and a/c ctrl assembly Hot at all times Hot in run, bulb test or start Iac a hi Iac a lo Iac b hi Iac b lo Iat sensor in Idle air control valve (top left rear of engine, on right front of throttle body) Ign ctrl a out Ign ctrl b out Injector 1 & 4 ctrl Injector 2 & 3 ctrl Instrument cluster Instrument cluster, cruise control and convenience center Intake air temp (iat) sensor (left front of engine comp, on right side of air cleaner) Map sensor (top left rear of engine, near throttle body) Map signal in Oil level signal Oxygen sensor (rear of engine on exhaust manifold) Oxygen sensor in-hi Oxygen sensor in-lo Pnk Red Sensor ground Tach Tan Throttle position (tp) sensor (top rear of engine, on left side of throttle body) Tps Vss out 2.2L (VIN 4), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Beretta Z26 1994 List of elements for 2.2L (VIN 4), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Beretta Z26 1994: 77 (right rear of engine, (under left side of driver's seat) 3rd gear sw 456/422 87a A/c control relay A/c relay ctrl A/t Brake switch (behind dash, on brake pedal support) C10 C11 C12 C13 C14 C15 C16 Canister purge sol valve (right front of engine compt) Conn c3 Convenience center Coolant fan relay Coolant fan relay ctrl Coolant ind ctrl Coolant indicator D10 D11 D12 D13 D14 D15 D16 Data link connector Dlc serial data in/out Egr solenoid ctrl Egr valve (left rear of engine, near map sensor) Electronic ignition (ei) system (rear of engine, above transaxle) Engine control module (ecm) (behind right side of i/p, near shroud) Evao ctrl Fuel pump prime conn Fuel pump relay (right rear of engine compt, behind strut tower) Fuel pump sw/ oil pres sender/sw (right rear of engine, near elect ignition (ei) system) Fuel tank/ pump unit Fuse 15a Fuse 20a Fuse block G117 G117 (right rear of engine, on trans stud) G300 Hot in run, bulb test or start Ignition Ignition coil Ignition switch Instrument cluster Knock sensor (rear of engine, below right side of exhaust manifold) Knock sensor in Low oil level ind ctrl Low oil level indicator M/t Malfunction ind ctrl Malfunction indicator Nca On transaxle stud) Park/neutral in Park/neutral position switch (a/t) (lower right rear of engine, top of transaxle) Pnk Pri Red Sec Shift indicator Spark plugs Sw a Sw b Tan Tcc solenoid Upshift ind/tcc ctrl Vehicle speed sensor (rear of engine) Vss in hi Vss in lo
2.3L 2.3L (VIN A), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Beretta Z26 1994 List of elements for 2.3L (VIN A), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Beretta Z26 1994: 132 #16 (iat) sensor (top left (left front of engine) (left rear of (left rear of engine, (lower right (rear of engine, (right rear of engine (top left side (under right side of 20 ga 20a 5v ref 87a A/c on input A/c pres sens input A/c pres sensor A10 A11 A12 Alarm module And a/c ctrl And wiper motor Assembly B/h B10 B11 B12 Base Batt ref Block C10 C11 C12 C13 C14 C15 C16 Compt, on relay bracket) Conn Conn c1 Conn c2 Cruise control, D10 D11 D12 D13 D14 D15 D16 Dash, at shroud) Ect sens input Eng coolant temp Engine Engine control module (ecm) Engine, above starter) Engine, at Engine, on top of Float Front of engine, Fuel Fuel pump Fuel pump relay Fuel pump rly ctrl Fuel pump sw/ Fuel tank unit Fus Fuse G114 G130 Gages Ground Ground (under Heater Hot at all times Hot in run, bulb Iat sens input Idle air control Idle air valve ctrl Ign ctrl a output Ign ctrl b output In exhaust manifold) Inj ctrl Injectors Input Instrument cluster Instrument cluster, Intake air temp Intake manifold) Left front seat) Link e Magnet Map sens input Map sensor (center front Multi-function Not O2 sens input-hi O2 sens input-lo Of engine) Of engine, above Oil level input Oil level sw Oil pan) Oil pres sw On intake manifold) On transaxle stud) Oxygen sensor Pin b4 Pin d6 Pk/bk Pnk Prime conn Red Red 2 Ref pulse input-hi Ref pulse input-lo Sens ground Sensor (left rear Sensor (lower left Side of engine) Spd output 4k/mile Speed Tach output Tan Tan 413 Tan 472 Test or start Throttle body) Throttle position (tp) Tp sens input Used Valve (left front of 2.3L (VIN A), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Beretta Z26 1994 List of elements for 2.3L (VIN A), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Beretta Z26 1994: 84 (bottom of dash, (left rear of engine) (lower left (top left front of engine) (top left side of engine) (under right side of 15a 20a A/c clutch Amplifier B/h Block C10 C11 C12 C13 C14 C15 C16 Canister purge valve Cluster Colnt fan rly ctrl Colnt temp ind ctrl Comp ctrl rly ctrl Conn Conn c3 Coolant Crankshaft position D10 D11 D12 D13 D14 D15 D16 Dash, at shroud) Data link conn Electronic ignition (ei) system Engine control module (ecm) Engine) Evaproative emission Fan control Fuse Hot in run, bulb Ignition Ignition coil Ignition module Ind Instrument Instrument cluster Knock sens input Knock sensor Left of steering column) Low oil Low oil ind ctrl Malfunction Malfunction ind ctrl Of engine, rear of Oil filter) Pin f4 Pin f5 Plugs Pnk Pnk 239 Pri Purge sol ctrl Rear of Relay Sec Sensor (lower right rear Serial data in/out Shift Shift ind ctrl Spark Sw a Sw b Switch Tan Tan 800 Temp ind Test or start Vehicle speed sensor Vss input-hi Vss input-lo
3.1L 3.1L (VIN M), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Beretta Z26 1994 List of elements for 3.1L (VIN M), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Beretta Z26 1994: 89 (left rear of engine rear of throttle body) (lower left hush panel) (on right side transaxle output housing) (right front of engine compartment) (right rear top of engine) (rust) (top rear of engine, in throttle body air tube) (top right rear of eng, near exhaust system) (top right side of 5 volt ref A/c clutch relay A/c press sens signal A/c relay ctrl A/c request A/c sensor Battery Brake sw input Check gauges lamp Conn c1 Conn c2 Convenience center Convenience center, speedo, Coolant temp sensor Cooling fan relay ctrl Cruise control, wiper/washer Data link connector Digital exhaust gas recirculation assembly Ect signal Egr sol "a" ctrl Egr sol "b" ctrl Egr sol "c" ctrl Engine, on rocker cover) Evap driver Evaporative emission canister purge valve Fan control relay Fuel pump relay ctrl Fuel pump relay monitor Fuse 10a Fuse 20a Fuse block Fusible link e G115 (center rear of engine on transaxle stud) G116 (left rear of engine compartment, on dash panel) Ground Heated oxygen sensor (upper right side of engine on exhaust manifold) Heater & a/c control assembly Hot at all times Hot in run Hot in run, bulb Idle air ctrl valve "a" (hi) Idle air ctrl valve "a" (lo) Idle air ctrl valve "b" (hi) Idle air ctrl valve "b" (lo) Idle air ctrl valve (top rear of engine, on throttle body) Instrument cluster Intake air temp sensor Low oil ind ctrl Malfunction ind control Malfunction indicator Manifold absolute pressure sensor Map signal Oil level signal Oxygen sensor ground Oxygen sensor signal Park/neutral out Pnk Pnp switch in Powertrain control module (upper right of i/p, attached to bracket) Red Sensor ground Serial data in/out Shift sol "a" ctrl Shift sol "b" ctrl Sol a Sol b Sol c Tan Tcc sol ctrl Test or start Throttle position sensor (rear of engine, right side of throttle body) Tps signal Trans fluid temp sensor Trans pos input "a" Trans pos input "b" Trans pos input "c" Vehicle speed sensor Vehicle speed sensor (hi) Vehicle speed sensor (lo) Vehicle speed signal 3.1L (VIN M), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Beretta Z26 1994 List of elements for 3.1L (VIN M), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Beretta Z26 1994: 58 (right top of engine 24x crank position sensor (front left of engine, on timing chain cover) 87a Automatic transaxle Brake switch (on brake pedal support) Cam position sensor in Camshaft position sensor (front top of engine) Compartment, behind generator) Conn c3 Crank pos sensor in Crank/cam pos sensor rtn Cruise control module Cruise on in E pnk Electronic ignition system Est bypass sig Est ctrl sig Fuel inj 1 out Fuel inj 2 out Fuel inj 3 out Fuel inj 4 out Fuel inj 5 out Fuel inj 6 out Fuel pump switch/oil pressure sensor sw (right front of engine block) Fuel pump priming conn Fuel pump relay (right rear of engine compt, behind strut tower) Fuel tank unit (top of fuel tank) Fuse 15a Fuse 20a Fuse block G115 (center rear of engine, on transaxle stud) G300 (under left front seat, near door sill) Ground Hot in run, bulb test, or start Ignition Ignition amplifier and switching module Inj Interlock Knock sensor (right front of engine block) Knock sensor in Mat sensor in Nca Park/neutral position switch (left rear of engine, right top of transaxle) Plugs spark Pnk Powertrain control module (upper right of i/p, attached to bracket) Red Ref pulse hi in Ref pulse low in Shift Shift sol a Shift sol b Spark plugs Tachometer Tan Tcc pwm sol Trans temp sensor Transaxle converter clutch
EXTERIOR LIGHTS Backup Lamps Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Backup Lamps Wiring Diagram for Chevrolet Beretta Z26 1994: 19 Back-up lights switch (rear of engine, on top of transaxle) C 1995 vftc Coupe Engine controls system (park/ neutral position switch) Exterior lights system (hazard lights circuit) Fuse 5 20a Fuse block (behind left side of i/p) G400 (left rear of trunk, near shocktower) Hot in run, bulb test or start L4 vin 4 & l4 vin a manual transaxle Left back up light Left back-up lights Park/neutral position switch (l4 vin 4) (lower right rear of engine, right top of transaxle) (v6 vin m) (left rear of engine, right top of transaxle) Pnk Right back up light Right back-up lights Sedan V6 vin m & l4 vin 4 automatic transaxle V6 vin m only Exterior Light Wiring Diagram (1 of 2) for Chevrolet Beretta Z26 1994 List of elements for Exterior Light Wiring Diagram (1 of 2) for Chevrolet Beretta Z26 1994: 48 1995 vftc c Anti-lock brakes system Brake switch (on brake pedal support) Canadian models only Center high mounted stop light assembly Convenience center (left side of i/p) Coupe & sedan w/luggage carrier Coupe w/spoiler Coupe/ sedan Exterior lights system (back up lights) Fuse 2 20a Fuse 5 20a Fuse 7 20a Fuse block (behind left side of i/p) G stop- turn G tail G129 (vina) (left rear of engine on transaxle stud) (vin4) (engine harness, right rear of engine on transaxle stud) (vin m) (engine harness, center rear of engine, on transaxle stud under exhaust pipe) G300 (under left side of driver seat, near door sill) G400 (left rear of trunk near shocktower) Hazard Hazard flasher Hazard switch Head Headlight switch Headlights system (daytime running lamps module) Hot at all times Hot in run, bulb test or start Indi- cators Instrument cluster Left tail/ stop-turn lights Left turn ind. Left turn sw Light switch Normal Off Park Pnk Right tail/ stop-turn lights Right turn ind. Right turn sw Stop- turn Tail To front lights To front park/turn lights To rear lights Turn flasher (behind left left side of i/p) Turn/ hazard switch Warning system Exterior Light Wiring Diagram (2 of 2) for Chevrolet Beretta Z26 1994 List of elements for Exterior Light Wiring Diagram (2 of 2) for Chevrolet Beretta Z26 1994: 31 1995 vftc c Coupe From light switch From turn/ hazard switch G park G tail G100 (left front of engine compartment, behind battery) G100 (left front of engine compartment, near battery) G400 (left rear of trunk, near shock tower) Left front marker light (w/o fog lights) Left front park/turn light Left front side marker light Left license light Left rear marker light Left rear side marker light Left tail/ stop/turn lights License light Park Right front marker light (w/o fog lights) Right front park/turn light Right front side marker light Right license light Right rear side marker light Right side marker light Right tail/ stop/turn lights Sedan Stop- g Stop- g tail Stop- turn Tail Turn
GROUND DISTRIBUTION Ground Distribution Wiring Diagram (1 of 2) for Chevrolet Beretta Z26 1994 List of elements for Ground Distribution Wiring Diagram (1 of 2) for Chevrolet Beretta Z26 1994: 98 (a/t) (center rear of engine, on transaxle stud near exhaust pipe) (left rear of engine compartment, (left rear of engine on transaxle stud) (left rear of engine, above starter) (left rear of engine, on transaxle stud) A/c A/c control A12 Abs Alarm Assembly B/h conn B12 Battery Blower Brake Brake fluid C13 Cluster Clutch Compartment Compressor Conn Control Control & Coolant Crankcase Cruise Data Daytime Defogger Diagnostic Diagnostic energy Diode Discriminating Electronic Energy Engine Fan Forward Fuel Function G114 (l4 vin a) G115 G116 (v6 vin m) G130 G130 (l4 vin 4 & v6 vin m) Heated Heater Heater/ Ignition Instrument Interlock L4 vin 4 L4 vin a L4 vin a only Lamp Left front Level Light sw Lights Link Low Module Motor Multi/ Nca Oil On dash panel) Oxygen Passenger Pin b7 Power Pump Radio Rear Relay Reserve Reserve module Right front Running Sensor Servo Shift Solenoid Switch System Tan Temp Transaxle Unlock V6 vin m V6 vin m only Valve Vent Washer sw Wiper/ Ground Distribution Wiring Diagram (2 of 2) for Chevrolet Beretta Z26 1994 List of elements for Ground Distribution Wiring Diagram (2 of 2) for Chevrolet Beretta Z26 1994: 100 (coupe (left front of engine (left rear of trunk, (right rear of engine, (under left front (under left front seat) A/t Ashtray Ashtray lt Assembly Back/up Back/up lt Back/up lts Belt sw C13 Center Cig Cluster Compt Compt, behind battery) Conn Console Control Coupe Coupe w/t96 Data Door Electronic Engine Fog lt Front door Fuel G100 G117 G300 G404 Headlt Headlt assembly Hi beam Hi level Ignition Instrument L4 vin 4 Lap Left Left composite Left front Left rear Left seat belt Left tail/stop/ License License lt Light Lighter Link Lo beam Lock Lock switches Luggage Marker Marker lt Module Motor Near shock tower) On transaxle stud) Park/neutral Park/turn Postion Pump Rear Relay Retractor solenoids Right Right composite Right front Right rear Right seat belt Right tail/stop/ Seat Seat, near door sill) Sedan Shift Shift lt Shoulder Side Side marker Stop lt Switch System Tan Tank Tank unit Turn lts Unit W/o a/c W/o t96) W/pwr Window Windows Wiper
HEADLIGHTS Fog Lamps Wiring Diagram, without DRL for Chevrolet Beretta Z26 1994 List of elements for Fog Lamps Wiring Diagram, without DRL for Chevrolet Beretta Z26 1994: 37 (left front of engine (left rear of engine (upper left (upper left Assembly B/h conn Beam Cluster Comp, near battery) Comp, on dash panel) Composite Dimmer Fog Fog lt relay Fog lts Fog lts in-line Fuse 20a G100 G115 G116 Head Headlt Headlt sw Hi beam Hot at all times Ind Instrument Left Light Off On transaxle stud) Park Pin a2 Pin f1 Right Side of i/p) Tan Headlight Wiring Diagram, with DRL for Chevrolet Beretta Z26 1994 List of elements for Headlight Wiring Diagram, with DRL for Chevrolet Beretta Z26 1994: 65 g115 g100 (behind right side of i/p, (center of dash) (left front of (left front of engine (left rear of engine, (under center console) (upper left (upper right side of 10a 20a Above glove box) Assembly B/h conn Battery Beam Block Brake Comp, near battery) Composite Conn c1 Conn c2 Daytime running lts (drl) module Dimmer Diode assembly Engine comp, Fog Fog lt relay Fog lts Fuse G100 Ground Head Headlt Hi beam Hi beam on input Hot at all times Hot in run Hot in run, bulb I/p along right side Ignition input In/line fuse Ind Instrument cluster Left Light Near battery) Of glove box) Off On ind On transaxle stud) Park Park brake input Park brake sw Photoresistor Photoresistor input Pin a1 Pin a2 Pin f1 Right Side of i/p) Tan Test or start Upper left Headlight Wiring Diagram, without DRL for Chevrolet Beretta Z26 1994 List of elements for Headlight Wiring Diagram, without DRL for Chevrolet Beretta Z26 1994: 27 (left front of engine (left rear of Assembly B/h conn Beam Cluster Comp, near battery) Composite Dimmer Engine, on G100 G115 Head Headlt Hi beam Hot at all times Ind Instrument Left Light Off Park Pin a2 Pin f1 Right Tan Transaxle stud)
HORN Horn Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Horn Wiring Diagram for Chevrolet Beretta Z26 1994: 10 Convenience center (left side of i/p) Fuse 15a Fuse block Horn relay Horn switch Hot at all times Left horn (left front of engine compt) Right horn (right front of engine compt) Slip ring Steering wheel
INSTRUMENT CLUSTER Instrument Cluster Wiring Diagram, Base for Chevrolet Beretta Z26 1994 List of elements for Instrument Cluster Wiring Diagram, Base for Chevrolet Beretta Z26 1994: 75 (not used) (vin a & 4) (vin m) (vin m) (vin 4 & a) (vin m) (vin a & 4) Abs lamp module (upper right side of i/p) Acc Antilock brake indicator Brake fluid level switch (left rear of engine compt) (closed w/ low brake fluid level) Brake indicator Bulb test C1 (vin a & 4) c1 (vin m) C2 c2 C2 c3 C3 (vin a & 4) c1 (vin m) C3 c2 Charge indicator Convenience center (left side of i/p) Daytime running lamps module (right side of i/p) Diagnostic energy reserve module (behind right front kick panel) Electronic brake control module (center rear of engine compt) Electronic brake control module (center rear of luggage compt) Engine controls system Engine coolant temp sender (right rear of engine) (1365 @100 f,38 c) (55 @260 f,127 c) Engine coolant temperature gauge Engine coolant temperature indicator Exterior lights system Fasten belts indicator Float magnet Fuel gauge Fuel gauge sender (top of fuel tank) (full-90 ) (empty-0 ) Fuel pump/ oil pressure switch/sender (right side of engine block) (open above 28kpa,4psi) Fuse 20a Fuse block G104 (left rear of engine compt) G114 (left rear of engine) G300 (below left front seat) Generator (right front of engine) Headlights system Hi beam indicator Hot in run, bulb test or start Ignition switch Illum- ination (2 bulbs) Indicator control Indicator control switch input Inflatable restraint indicator Instrument cluster Interior lights system Left turn indicator Lock Low coolant indicator Low coolant switch (right front of engine comp) Low oil level indicator Malfunction indicator Multi- function alarm module Nca Off Oil level switch (right side of engine) (open w/ low oil level) Oil pressure indicator Park brake switch (open with park brake released) Pnk Powertrain control module (right side of i/p) Powertrain control module (upper right side of i/p) Right turn indicator Run Shift indicator Solid state Speedometer Start Tan Vehicle speed output Vin a & 4 w/ m/t only Vin m only W/ drl W/o drl Instrument Cluster Wiring Diagram, Gauges for Chevrolet Beretta Z26 1994 List of elements for Instrument Cluster Wiring Diagram, Gauges for Chevrolet Beretta Z26 1994: 76 (vin a & 4) (vin m) (vin m) (vin 4 & a) (vin m) (vin a & 4) Abs lamp module (upper right side of i/p) Acc Antilock brake indicator Brake fluid level switch (left rear of engine compt) (closed w/ low brake fluid level) Brake indicator Bulb test C1 (vin a & 4) c1 (vin m) C2 c2 C2 c3 C3 (vin a & 4) c1 (vin m) C3 c2 Convenience center (left side of i/p) Daytime running lamps module (right side of i/p) Diagnostic energy reserve module (behind right front kick panel) Electronic brake control module (center rear of engine compt) Electronic brake control module (center rear of luggage compt) Electronic ignition system (right top of engine compt) Engine coolant temp sender (right rear of engine) (1365 @100 f,38 c) (55 @260 f,127 c) Engine coolant temperature gauge Engine coolant temperature indicator Exterior lights system Fasten belts indicator Float magnet Fuel gauge Fuel gauge sender (top of fuel tank) (full-90 ) (empty-0 ) Fuel pump/ oil pressure switch/sender (right side of engine block) (open above 28kpa,4psi) Fuse 20a Fuse block G104 (left rear of engine compt) G114 (left rear of engine) G300 (below left front seat) Headlights system Hi beam indicator Hot in run, bulb test or start Ignition switch Illum- ination (4 bulbs) Indicator control Indicator control switch input Inflatable restraint indicator Instrument cluster Interior lights system Left turn indicator Lock Low coolant indicator Low coolant switch (right front of engine comp) Low oil level indicator Malfunction indicator Multi- function alarm module Nca Off Oil level switch (right side of engine) (open w/ low oil level) Oil pressure gauge Park brake switch (open with park brake released) Pnk Powertrain control module (right side of i/p) Powertrain control module (upper right side of i/p) Right turn indicator Run Shift indicator Solid state Speedometer Start Tachometer Tan Vehicle speed output Vin 4 & a Vin a & 4 w/ m/t only Vin m Vin m only Voltmeter W/ drl W/o drl
INTERIOR LIGHTS Courtesy Lamps Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Courtesy Lamps Wiring Diagram for Chevrolet Beretta Z26 1994: 39 1995 vftc c Batt Cigar lighter switch Convenience center (left side of i/p, above fuse block) Dimmer switch Dome light Fuse 11 15a Fuse 6 20a Fuse 9 20a Fuse block (behind left side of i/p) G114 (vin a) (left rear of engine compartment, above starter) g129 (vin m) (left rear of engine compartment on transaxle stud) (vin 4) (left rear of engine on transaxle stud) G300 (under left side of driver seat) G300 (under left side of driver seat, near door sill) G300 (under left side of driver seat, next to door sill) G902 (left side of windshield header) Gnd Hot at all times Hot in run, bulb test, or start Ign Interior lts ctrl Left fnt dr opn in Left footwell courtesy light Left front door handle switch (in left front door latch assembly) Left rear door jamb switch (in center pillar) Light switch Luggage compartment light Multi-function alarm module Nca Off Overhead lights Parasitic pwr ctrl Pnk Reading lights Rear dr opn in Right fnt dr opn in Right footwell courtesy light Right front door handle switch (in right front door latch assembly) Right rear door jamb switch (in center pillar) Sedan only Instrument Illumination Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Instrument Illumination Wiring Diagram for Chevrolet Beretta Z26 1994: 28 1995 vftc c Canadian models only Console ashtray light Console shift light Convience center (left side of i/p, above fuse block) Coupe only Daytime running lights (drl) module (right side of i/p, above glove box) Display dim signal Exterior lights system (rear lights) Fuse 13 3a Fuse block (behind left side of i/p) G114 (vin a) (left rear of engine compartment, above starter) g129 (vin m) (left rear of engine compartment on transaxle stud) (vin 4) (left rear of engine on transaxle stud) G300 (under left side of driver seat, near door sill) Head Headlight switch Heater & a/c control assembly Hot at all times Instrument cluster Light switch Light switch light Multi-function alarm mdule Off Park Pwm module Radio Rear defogger control & wiper/washer switch Sedan only W/rear defogger
PASSIVE RESTRAINTS Passive Restraint Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Passive Restraint Wiring Diagram for Chevrolet Beretta Z26 1994: 40 (v6 vin m) (l4 vin 4 & a) (vin 4 & m) (vin 4) (vin a) (vin m) A nca Battery C2 c2 Convenience center (behind left side of i/p, above fuse block) Engine control module (behind right side of i/p) Fasten belts indicator Fasten belts indicator control Fuse 15a Fuse 20a Fuse block G117 (right rear of engine, g115 (center rear of engine, on transaxle stud) g130 (left rear of engine, on transaxle stud) G130 (left rear of engine) g114 (center rear of engine) G300 (under left front seat) G300 (under left front seat, near door sill) Ground Hot at all times Hot in run, bulb test or start Ignition Instrument cluster Left front door handle switch Left front door open input Left seat belt lap retractor release solenoid (left door) Left seat belt shoulder retractor release solenoid (left door) Multi- function alarm module Nca Pnk Right front door handle switch Right front door open input Right seat belt lap retractor release solenoid (right door) Right seat belt shoulder retractor release solenoid (right door) Seat belt input Seat belt solenoid control Seat belt switch (part of driver's seat belt assembly) Vehicle speed input Vehicle speed output
POWER DISTRIBUTION Power Distribution Wiring Diagram (2 of 3) for Chevrolet Beretta Z26 1994 List of elements for Power Distribution Wiring Diagram (2 of 3) for Chevrolet Beretta Z26 1994: 85 #11 (l4 vin 4 (not used) (under left (v6 vin m 10a 15a 2 door 20a 25a 30a 4 door A/c/heater Alarm Alternator Assembly B/h conn Block Brake Cb #12 Cig Compt Console Control Coupe Coupe w/o t96 Crankcase Daytime Daytime running Door Door sill) Electronic Flasher From From lt sw Front door Front seat, near Function Fus link b Fus link d Fuse G300 Hazard Heated Heater Horn Ignition sw Left Left front Left rear Left tail/stop & License License lt Light Lighter Lock switches Lts module Luggage Marker lt Module Motor Multi- Only) Oxygen Park/turn Pin b1 Pin c4 Radio Red Relay Release Right Right front Right rear Right tail/stop & Running Sedan Sensor Side marker Temp valve To fuse #17 Turn lts Unlock Vent Window sw Power Distribution Wiring Diagram (3 of 3) for Chevrolet Beretta Z26 1994 List of elements for Power Distribution Wiring Diagram (3 of 3) for Chevrolet Beretta Z26 1994: 85 #17 (a/t) (fuse block) (l4 vin 4 only) (not used) (v6 vin m only) 10a 15a 20a A/c A/t Abs lp Alarm B/h conn Back/up Block Brake sw Camshaft Canister purge Cluster Clutch Control Control & Converter Crankshaft D16 Daytime Defogger Diagnostic Digital Door Electronic Electronic ignition system Emission Energy Engine Engine control Evaporative Exhaust Exhaust gas Flasher From From door unlock module Front door Function Fuse Fuse #11 Fuse #16 Gas Ignition Ignition sw Injector Instrument L4 vin 4 L4 vin a Left Lock Lock switches Lt sw M/t Module Multi/ Pin a Pin d Pin f4 Pnk Position Position sw Rear Recirculation Relay Reserve Right Running lts Sensor Solenoid System Torque Transaxle Turn Unlock V6 vin m Valve Washer sw Wiper/
POWER DOOR LOCKS Power Door Lock Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Power Door Lock Wiring Diagram for Chevrolet Beretta Z26 1994: 52 (behind left lower kick panel) (left rear of engine, on transaxle stud) (notused) (vin 4 and vin a) (vin m) (vin 4) (vin a) (vin m) Auto door unlock module (rifght side of i/p, near derm module) Bat C2 c2 Circuit breaker 15 30a Door lock Engine control module (right upper i/p attached to bracket) Engine control module (right upper i/p, attached to bracket) Engine controls system Fuse 15a Fuse 10a Fuse 15a Fuse 20a Fuse block G104 (left rear of engine compartment, above starter) G104 (left rear of engine compartment, on transaxle stud) G114 G117 (right rear of engine on transaxle stud) G300 (below driver's seat) Gnd Hot at all times Hot in run, bulb test or start Ign Left door lock switch Left front door lock motor Left rear door lock motor (4-door only) Lock Lock relay Multi- function alarm module (in convenience center) Park/ neutral input Park/ neutral position switch (top right side of transaxle) Pnk Relay assembly Relay control Right front door lock motor Right rear door lock motor (4-door only) Right door lock switch Solid state Tan Unlock Unlock control Unlock relay Vehicle speed input Viin 4 with a/t Vin a and vin 4 with manual transaxle Vin m
POWER WINDOWS Power Window Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Power Window Wiring Diagram for Chevrolet Beretta Z26 1994: 10 30a Circuit breaker 12 Console window switch Fuse block G300 (below left front seat) Hot in run Left front power window motor One touch window down module Right front power window motor Tan
RADIO Radio Wiring Diagrams for Chevrolet Beretta Z26 1994 List of elements for Radio Wiring Diagrams for Chevrolet Beretta Z26 1994: 26 Antenna Antenna input Bat power input Coaxial cable Convenience center Dim signal Fuse 15a Fuse block G129 (lower left front of engine) Ground Hot in acc or run Interior lights system Left front speaker Left rear speaker Lt frt spkr Lt rr spkr Multi- function alarm module Nca Panel light Power in Radio Right front speaker Right rear speaker Rt frt spkr Rt rr spkr Tan
SHIFT INTERLOCKS Shift Interlock Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Shift Interlock Wiring Diagram for Chevrolet Beretta Z26 1994: 16 (left of steering column, on support bracket) (vin m & vin 4: left rear of engine, on transaxle stud) (vin a: left rear of engine compt, above starter) Brake switch (brake pedal support) Brake transaxle shift interlock solenoid (left of steering column) Brake transaxle shift interlock solenoid (underside of steering column) Buick skylark oldsmobile achieva pontiac grand am Chevrolet corsica chevrolet beretta Engine controls system Erls fuse 15a Fuse 20a Fuse block G130 G204 Hot in run, bulb test or start Pnk Pnk c
STARTING/CHARGING Charging Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Charging Wiring Diagram for Chevrolet Beretta Z26 1994: 36 (left front of engine compt, behind battery) (not used) p (solid state) (vin a & 4) (vin m & 4- left rear of engine, on transaxle stud) (vin m) 10a 20a Base cluster only Bat Battery Charge ind. Field (rotor) Fuse 4 Fuse 9 Fuse block Fusible link (14 ga- rust) Fusible link (16 ga- rust) Fusible link (16 ga-rust) Fusible link (20 ga-rust) G100 G114 Generator (upper right front of engine) Ground distribution Hot in run Hot in run, bulb test or start Instrument cluster Pnk Power distribution Rectifier bridge Red Regulator Starter solenoid (lower left rear of engine) Stator Turn on input Voltage sensing input Starting Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Starting Wiring Diagram for Chevrolet Beretta Z26 1994: 31 (left front of engine compt, behind battery) (vin a- left rear of engine, above starter) (vin m & 4- left rear of engine, on transaxle stud) *l4 vin a & 4 **v6 vin m A/t Accy Battery Bulb test Clutch pedal position switch (left of i/p, left of clutch pedal) F * ** Fusible link (16 ga- rust) Fusible link (20 ga-rust) G * ** G100 G114 Ground distribution Hold-in winding Ignition switch Lock M/t Off Park/ neutral position switch (top right of transaxle) Power distribution Pull-in winding Red Release relay Run Solenoid contacts Start Starter motor Starter solenoid (lower left rear of engine)
SUPPLEMENTAL RESTRAINTS Supplemental Restraint Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Supplemental Restraint Wiring Diagram for Chevrolet Beretta Z26 1994: 49 2.49 k 5.1 k 8.45 k A10 A11 A12 Air bag fuse 3a Air bag ind Arming sensor (upper right side of i/p, attached to underside of upper dash panel) B10 B11 B12 Convenience center (left side of i/p, above fuse block) Crank input Data link conn (dlc) (left side of i/p) Diagnostic energy reserve module (derm) (behind right front kick panel) Driver 36v loop rsrv Driver seat belt Driver side "high" Driver side "low" Driver source sense Engine controls Forward discriminating sensor (attached to radiator support) Fuse 10a Fuse 20a Fuse block G114 (vin a) (left rear of engine, above starter) G130 (vin 4 & vin m) (left rear of engine, on transaxle stud) G300 (under left front seat) Ground Hot in run, bulb test or start Hot in start Ign 1 In-line fuse (upper left side of i/p, taped to i/p harness) Initiator module (under center of steering wheel) Instrument cluster Left front seat belt input Multi- function alarm module Nca Passenger compartment discriminating sensor (under center console) Pnk Redundant ind ground Redundant ind ign 1 Seat belt sw Serial data line Shorting bar Sir coil assembly (top of steering column) Sir indicator ctrl Tan
TRANSMISSION Transmission Wiring Diagram, 4T60-E for Chevrolet Beretta Z26 1994 List of elements for Transmission Wiring Diagram, 4T60-E for Chevrolet Beretta Z26 1994: 66 (20 ga-rust) (center rear of engine, on transaxle stud) (left lower hush panel) (partial) 5v ref A/c on in A/c sensor Automatic transaxle Battery ref Brake switch (on brake pedal support) Brake transaxle shift interlock solenoid Clutch Conn c1 Conn c2 Conn c3 Data link connector Ects in Engine coolant temperature (upper right rear of engine, near exhaust system) Fuse 1 15a Fuse 5 20a Fuse 9 20a Fuse block Fusible link G115 Gnd Heater and a/c control assembly Hot at all times Hot in run, bulb test or start Ign Instrument cluster Malfunction indicator lamp Map sensor Mil ctrl Multi- function alarm module Nca P/n in P/n sig out Park/neutral position switch (left rear of engine, right top of transaxle) Pnk Pnp switch a in Pnp switch b in Pnp switch c in Pnp switch parity in Powertrain control module (pcm) (right upper i/p, attached to bracket) Red Sensor Sensor gnd Serial data in/out Shift a solenoid Shift b solenoid Shift sol a ctrl Shift sol b ctrl Tan Tcc ctrl Tcc pwm sol ctrl Tcc pwm solenoid Temp. Throttle position position (rear of engine, right side of throttle body) Tps in Trans fluid temp sensor in Transaxle Transaxle converter Vehicle speed sensor (lower right front of engine, on right transaxle output shaft housing) Vss in-hi Vss in-lo With a/c
TRUNK, TAILGATE, FUEL DOOR Trunk Release Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Trunk Release Wiring Diagram for Chevrolet Beretta Z26 1994: 28 (vin m) (vin 4) A/t Acc Brake warning system Bulb test C1 c1 Drl module (right side of i/p) E g Fuse 20a Fuse block G f Hot at all times Ignition switch Lock M/t Off Park brake switch Park/neutral position switch (left rear of engine) Red Release switch Run Start Starter solenoid Starting/ charging system Trunk lid release solenoid Trunk release relay (behind left kick panel) W/ drl W/o drl
WARNING SYSTEMS Warning System Wiring Diagrams for Chevrolet Beretta Z26 1994 List of elements for Warning System Wiring Diagrams for Chevrolet Beretta Z26 1994: 56 (center rear of engine compart- ment) (left side of i/p, above fuse block) (left side of i/p, right of steering column) (under right side of i/p at shroud) (v6 vin m) (l4 vin a & 4) A nca Bat Battery C2 c2 Convenience center Daytime running lights module (above glove box) Electronic brake control module c2 Engine control module Exterior lights system Fasten belts indicator Fasten belts indicator control Fuse 15a Fuse 20a Fuse block G104 (left rear of engine compartment) G130 (on transaxle stud) G300 (under left front seat) Ground Head Hot at all times Hot in run, bulb test or start Ignition Ignition switch Input Instrument cluster Key in ignition Left rear door jamb switch Left front door Left front door handle switch Lights on input Lights-on output Multi- function alarm module Nca Nca d Off Open input Parasitic power control Park Pnk Radio Rear door open input Right front door Right front door handle switch Right rear door jamb switch Seat belt Seat belt switch (under center console) Turn flasher Turn signal input Turn/hazard- headlight switch assembly Vehicle speed input Vehicle speed output
WIPER/WASHER 2-Speed Wiper/Washer Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for 2-Speed Wiper/Washer Wiring Diagram for Chevrolet Beretta Z26 1994: 14 Fuse 10 25a Fuse block G100 (left front of eng compt, behind battery) Hot in accy or run Mechanical arm Mist Not used Off Rear defogger control and wiper/ washer switch Red Washer motor Washer switch Wiper motor assembly Wiper switch Interval Wiper/Washer Wiring Diagram for Chevrolet Beretta Z26 1994 List of elements for Interval Wiper/Washer Wiring Diagram for Chevrolet Beretta Z26 1994: 24 (left front of eng compt, behind batt) Cover assembly Delay Delay input Delay output Engine control module (vehicle speed sensor) Fuse 10 25a Fuse block G100 Gnd Hot in accy or run Mechanical arm Mist Off Park switch Pulse Red Solid state timer Vehicle speed input Washer motor Washer switch Wiper motor assembly Wiper switch Wiper/ washer switch
