Diagram sections — 21 (35 total)
AIR CONDITIONING ANTI-LOCK BRAKES COMPUTER DATA LINES COOLING FAN DEFOGGERS ENGINE PERFORMANCE EXTERIOR LIGHTS GROUND DISTRIBUTION HEADLIGHTS HORN INSTRUMENT CLUSTER INTERIOR LIGHTS POWER DISTRIBUTION POWER DOOR LOCKS RADIO SHIFT INTERLOCKS STARTING/CHARGING SUPPLEMENTAL RESTRAINTS TRANSMISSION WARNING SYSTEMS WIPER/WASHER
AIR CONDITIONING A/C Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for A/C Wiring Diagram for Chevrolet Metro LSi 1998: 58 (i/p harness, 8 cm from blower motor breakout) (i/p harness, behind right side of dash) (main harn, 18 cm from left firewall grommet) (main harn, behind left side of dash) 1995 vftc c A/c 1 relay A/c 2 relay A/c amplifier (below right side of dash, on evaporator case) A/c compressor clutch A/c condenser fan motor A/c fuse 15a A/c off A/c relay A/c req A/c switch Blower motor Blower motor resistor (in blower housing assembly) Blower speed selector switch Dual pres sw Dual pressure switch (right side of engine compartment, near strut tower) Engine controls system Evap temp Evaporator thermistor (behind right side of dash) Fuse box G100 (left front of engine compt) G101 (right front of engine compt) G200 (left kick panel) G206 (center of dash) Ground Heater fuse 20a Hot at all times Hot in on Hot in on or start Idle up Idle-up Ig-coil fuse 15a Ign Junction block Off Pnk Powertrain control module (pcm) (behind right side of dash, near glove box) Radiator fan motor Rdtr fan relay Rdtr fuse 30a Relay box Relay ctrl S122 (main harn, at relay box) S123 (main harn, 4 cm from ignition control module breakout) S134 (a/c jumper harn, right front of engine compartment) S202 (main harn, 8 cm from junction block connector c6 breakout) S210 S232 (i/p harn, center of dash) S233 S238 (i/p harness, 3 cm from blower motor breakout) S247 S247 (main harn, 18 cm from left firewall grommet) S254 Sensor ground Compressor Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Compressor Wiring Diagram for Chevrolet Metro LSi 1998: 29 (i/p harness, 8 cm from blower motor breakout) A/c 1 relay A/c 2 relay A/c amplifier (below right side of dash, on evaporator case) A/c compressor clutch A/c fuse 15a A/c off A/c relay A/c req A/c switch Blower speed selector switch Dual pres sw Dual pressure switch (right side of engine compartment, near strut tower) Evap temp Evaporator thermistor (behind right side of dash) Fuse box G101 (right front of engine compt) Heater fuse 20a Hot at all times Hot in on Junction block Off Pnk Powertrain control module (pcm) (behind right side of dash) Relay box S122 (main harn, at relay box) S134 (a/c jumper harn, right front of engine compartment) S233 Sensor ground Heater Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Heater Wiring Diagram for Chevrolet Metro LSi 1998: 14 1995 vftc c Blower motor Blower motor resistor (in blower housing assembly) Blower speed selector switch Engine controls system G206 (center of dash) Heater fuse 20a Hot in on Junction block Off Pnk S232 (i/p harness, behind center of dash) S233 (i/p harness, 3 cm from blower motor breakout) S233 (i/p harness, 8 cm from blower motor breakout)
ANTI-LOCK BRAKES Anti-lock Brake Wiring Diagrams for Chevrolet Metro LSi 1998 List of elements for Anti-lock Brake Wiring Diagrams for Chevrolet Metro LSi 1998: 91 (i/p harn, 1 cm from cluster breakout) s249 (left kick panel) g200 (main harn, 9cm from relay box breakout) s121 1m03 2c03 2o02 6b01 6c01 6d01 6e01 6f01 6g01 6h01 6i01 6j01 6k01 6l01 6m01 6n01 6o01 6p01 6q01 6r01 6s01 6u01 6v01 6w01 7h01 7i01 A10 A11 A12 Abs active Abs active ind Abs control module (left side of dash) Abs enable Abs fuse 40a Abs ind Abs motor pack assembly B10 B11 B12 Battery feed Brake ind Brake ind ctrl Brake light switch Brake signal Data link connector on board diagnostics ii (upper left side of dash) Def fuse 20a Electronic brake control relay (in relay box) Fuse box G100 (left front of engine compt) Ground Hazard fuse 15a Hot at all times Hot in on Hot in on or start Ig-coil fuse 15a Ignition power Instrument cluster Junction block Lamp driver relay (left side of dash) Lamp drvr rly Left front speed sensor Left rear speed sensor Lf motor Lf solenoid Lft frt motor Lft frt sens in Lft frt sol out Lft rr sens in Pnk Rear motor Rf motor Rf solenoid Right front speed sensor Right rear speed sensor Rt frt motor Rt frt sens in Rt frt sol out Rt rr sens in S124 (main harn, 5 cm from front abs solenoids breakout) S206 (main harn, 22 cm from stop lamp switch breakout) S208 S215 S242 S251 Serial data Stop fuse 15a Stop lamp switch (top of brake pedal switch) Switched batt
COMPUTER DATA LINES Computer Data Lines for Chevrolet Metro LSi 1998 List of elements for Computer Data Lines for Chevrolet Metro LSi 1998: 14 (center rear of engine) Data link connector- on board diagnostics ii (under left side of dash, by center console) Dome fuse 15a Electronic brake control module (behind left side of dash, above junction block) G131 G202 (left side of dash) Hot at all times Inflatable restraint sensing & diagnostic module (sdm) (behind center console, forward of manual selector lever) Junction block Powertrain control module (behind right side of dash, near glove box) S222 S240 S245 S249 (i/p harness, approx 1cm from cluster connector c2 breakout)
COOLING FAN Cooling Fan Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Cooling Fan Wiring Diagram for Chevrolet Metro LSi 1998: 32 (a/c jumper harn, right front of engine compt) (left front of engine compt) (main harn, 18 cm from left firewall grommet) (main harn, at relay box) s122 (right front of engine compt) A/c 1 relay A/c 2 relay A/c amplifier (below right side of dash, on evaporator case) A/c compressor clutch A/c condenser fan motor A/c fuse 15a A/c relay Fuse box G100 G100 (left front of engine compt) G101 Hot at all times Hot in on junction block Hot in on or start Htr fuse 20a Ig fuse 15a Pnk Powertrain control module (behind right side of dash, near glove box) Radiator fan motor Rdtr fan relay Rdtr fuse 30a Relay box Relay ctrl S123 (main harn, 4 cm from left firewall grommet) S134 S202 (main harn, 8 cm from junction block conn c6 breakout) S247
DEFOGGERS Defogger Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Defogger Wiring Diagram for Chevrolet Metro LSi 1998: 21 (2-door) (left side of hatch- back door, behind trim panel) (i/p harn, behind left end of dash) C406 Def fuse 20a Engine controls system G202 G411 G413 (4-door) (behind right rear quarter trim panel) Hot in on I/p cluster assembly Interior lights system Junction block (left side of dash) Junction block (on left side of dash) Not used Off Rear defogger switch Rear defogger Rear defogger indicator S223 S236 S239
ENGINE PERFORMANCE
1.0L 1.0L (VIN 6), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Metro LSi 1998 List of elements for 1.0L (VIN 6), Engine Performance Wiring Diagrams (1 of 2) for Chevrolet Metro LSi 1998: 95 (center rear of engine) g115 (engine harn, left rear of engine compt) (engine harness, near center of firewall) s262 (main harness, left side of engine compt) (main harness, near junction block) A/c amplifier A/c cut-out Air conditioning system Camshaft position (cmp) sensor Ckp sensor Cmp sensor Cooling fan system Crankshaft position (ckp) sensor (bottom of engine, near crankshaft pulley) Data link connector on board diagnostics ii (dlc-obd ii) (left side of dash) Defogger system Diag request sig Diode module (behind center of dash) Distributor (left side of engine) Distributor cap Dome fuse 15a Duty check data link connector (left rear of engine compt) Early fuel evaporative (efe) heater (between intake manifold and red Early fuel evaporative heater relay (ptc htr) Ecm ground Ect input Efe on sig Egr bypass cntrl Egr sol cntrl Engine start sig Evap canister tank pressure control solenoid vacuum valve (top of fuel tank) Evap canister vent solenoid valve (rear of engine compt) Evap cann cntrl Evap cvsv ctrl Evap tpcsvv ctrl Fuel level Fuel pres Fuel pump relay Fuel tank pressure sensor (in fuel tank) Fuse box (left of eng compt, behind battery) G115 (center rear of engine, on intake manifold) Ground Ho2s1 heater Ho2s1 input Ho2s2 heater Ho2s2 input Hot at all times Iat input Idle switch sig Idle-up sig Ign coil control Ign pwr input Ign trig input ignition control module (left side of fire- wall) Ign trigger sig Ignition Ignition coil (left side of firewall) Inj control Instrument cluster system Instrument cluster system (tachometer) Interior lights system Isc motor cntrl Isca relay cntrl Junction block (behind left side of dash) Map input Memory power Mil ind control Nca Noise suppressor filter (left rear of firewall) Pcm ground Pnk Powertrain control module (pcm) (behind right side of dash) Ptc fuse 30a Ptc relay cntrl Rad fan relay Red Ref voltage Relay box (left front of engine compartment) Relay control S110 S111 S130 S167 S170 S200 S248 S261 Sensor ground Serial data out Starting system Tach sig Test sw sig Throttle body) To spark plugs Tp input Upshift ind cntrl Vss input 1.0L (VIN 6), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Metro LSi 1998 List of elements for 1.0L (VIN 6), Engine Performance Wiring Diagrams (2 of 2) for Chevrolet Metro LSi 1998: 64 (center of engine, attached to air cleaner housing) (center rear of engine compt, on intake manifold) (engine harn, 4 cm from egr sv valve breakout) (engine harness, right rear of engine compt) (main harn, 23 cm from map sensor breakout) (main harn, 28 cm from front wiper motor breakout) (main harness, center rear of eng compt) (main harness, left side of engine compt) (main harness, right rear of eng compt) (near deck lid striker) g407 (right of engine, in thermostat housing) Compartment) Egr bypass valve (top rear of engine) Egr solenoid vacuum (egr sv) valve (left side of engine) Engine coolant temperature (ect) sensor Evaporative canister purge valve (center of firewall) Fi fuse 15a c1 Fuel injector (in throttle body) Fuel injector resistor (left rear of engine compartment) Fuel pump Fuel pump relay Fuel sender assembly (in fuel tank) Fuse box (left of eng compt, behind battery) G115 Heated oxygen sensor 1 (ho2s) (front of engine in exhaust manifold) Heated oxygen sensor 2 (ho2s) (after 3-way catalytic converter) Hot at all times Hot in on or start Idle Idle speed control (isc) motor (top of engine, on throttle body) Ig-coil fuse 15a Instrument panel cluster assembly Intake air temperature (iat) sensor Isc relay Junction block (behind left side of dash) Main relay Malfunction indicator Manifold absolute pressure (map) sensor (right rear of engine compartment) Nca Open at idle Pnk Red Relay box (left front of engine Relay box (left front of engine compt) S118 S119 S120 S126 S129 S130 S131 S148 S151 S152 S153 S156 S168 S169 S257 S313 Switch Throttle position (tp) sensor (on throttle body) Upshift indicator (m/t only) Vehicle speed sensor (vss)
1.3L 1.3L (VIN 2), Engine Performance Wiring Diagrams (1 of 3) for Chevrolet Metro LSi 1998 List of elements for 1.3L (VIN 2), Engine Performance Wiring Diagrams (1 of 3) for Chevrolet Metro LSi 1998: 75 (engine harn, near center of firewall) (engine harn, right rear of engine compt) (main harn, 50 cm from wimer motor breakout) A/t Acc Camshaft position sensor (near ignition coil) Clutch pedal position switch (above clutch pedal) Cooling fans system Crankshaft position (ckp) sensor (bottom of engine, by crankshaft pulley) Dome fuse 15a Ecm ground Ect input Engine start sig Evap can cntrl Evap can vent Evap canister purge valve (top rear of engine) Evap canister vent control solenoid (top of fuel tank) Evap tank pres Evap tank pressure control solenoid vacuum valve (center of engine compartment) Fuel injectors Fuel pump relay G115 (center rear of engine) Generator Ground Ho2s1 heater Ho2s1 input Ho2s2 heater Hot at all times Iat input Ign pwr input Ign ref Ign trigger 1-4 Ign trigger 2-3 Ignition coil 1 (on cylinder head) Ignition coil 2 (on cylinder head) Ignition switch Inj 1 ctrl Inj 2 ctrl Inj 3 ctrl Inj 4 ctrl Junction block (behind left side of dash) Junction block (behind left side of dash) Lock M/t Map input Memory power Mil ind control Nca Pcm ground Pnk Powertrain control module (pcm) (behind right side of dash) Pwr steer press Rad fan relay Red Ref voltage Relay control Run S119 S130 S159 S160 S161 S165 S248 S262 S263 Sensor ground Shift sol a Shift sol b Solid state Spark plugs Start Tp input Trans- axle range switch (on trans- axle) Vss 1.3L (VIN 2), Engine Performance Wiring Diagrams (2 of 3) for Chevrolet Metro LSi 1998 List of elements for 1.3L (VIN 2), Engine Performance Wiring Diagrams (2 of 3) for Chevrolet Metro LSi 1998: 34 (engine harn, near center of firewall) (i/p harn, 3 cm from cluster connector breakout) (left of eng compt, behind battery) 2nd brake solenoid (attached to valve body) Back fuse 15a Direct clutch solenoid (attached to valve body) Fi fuse 15a c1 Fuel level sensor Fuel pump Fuel pump relay Fuel sender assembly (in fuel tank) Fuel tank pressure sensor (in fuel tank) Fuse box G407 (center rear of trunk) Hot at all times Hot in on or start Instrument cluster system Junction block (behind left side of dash) Main relay Manifold absolute pressure (map) sensor (on intake plenum) N d Pnk Power steering pressure switch (on power steering pump) Red Relay box (left side of engine compartment) S129 (engine harn, right rear of engine compt) S151 S154 S158 S226 S259 S315 Transaxle range switch (top of transaxle) Vehicle speed sensor (vss) (top of transaxle) 1.3L (VIN 2), Engine Performance Wiring Diagrams (3 of 3) for Chevrolet Metro LSi 1998 List of elements for 1.3L (VIN 2), Engine Performance Wiring Diagrams (3 of 3) for Chevrolet Metro LSi 1998: 66 (center rear of engine) g115 (engine harn, 4 cm from pcm breakout) (engine harn, 8 cm from map sensor breakout) (engine harn, near center of firewall) (not used) 2 pos sig A/c cut A/c idle up A/c system D pos sig Data link connector on board diagnostics ii (dlc-obdii) (left side of dash) Defogger system Diag req Diode module (behind center of dash) Duty check data link connector (left rear side of engine compt) Duty out Engine coolant temperature (ect) sensor (left side of engine, in thermostat housing) Ft pres Fuel lev G115 (center rear of engine) Heated oxygen sensor 1 (ho2s) (in exhaust manifold) Heated oxygen sensor 2 (ho2s) (after 3-way catalytic converter) Ho2s 2 sig Hot in on or start Iac valve Idle air control valve (top of engine, on throtle body) Idle up Ig-coil fuse 15a Ignition Instrument cluster system Instrument panel cluster assembly Intake air temperature (iat) sensor (center of eng, attached to air cleaner housing) Interior Junction block (behind left side of dash) L pos sig Lights system Malfunction indicator N pos sig Nca Not used P pos sig Pnk Powertrain control module (behind right side of dash) R pos sig Red S101 S126 S130 S131 (engine harn, 9cm from generator breakout) S152 S153 S156 S163 (engine harn, 2 cm from injector breakout) S164 S167 S242 S248 S261 S263 Sensor gnd Serial data Tach Test sw sig Throttle position (tp) sensor (on side of throttle body) Upshift indicator (m/t only) Vehicle speed sensor (vss) (m/t)
EXTERIOR LIGHTS Backup Lamps Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Backup Lamps Wiring Diagram for Chevrolet Metro LSi 1998: 19 (2-door) s402 (4 door) s407 (floor harness, 13cm from g407 breakout (2-door), floor harn, 27cm from left rear combination lamp connector breakout (4 door) A/t Back fuse 15a Backup lamp Backup lamp switch (top of transaxle) G407 (near deck lid striker) Hot in on and start Junction block Left rear combination lamp M/t Red Red red Right rear combination lamp S401 S411 S413 Transaxle range switch (top of transaxle) Transmissions system Exterior Lamps Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Exterior Lamps Wiring Diagram for Chevrolet Metro LSi 1998: 73 (2 door) (a/t) (floor harness, approx 13cm (2-door) 34cm (4-dr) from left rear combination lamp conn breakout) (floor harness, approx 36cm from hatchback door harness breakout (2-door), floor harness, approx 39cm from left rear combination lamp connector breakout (4-door) s400 (floor harness, approx 8cm from g407 breakout (2-door), floor harness, approx 10cm from luggage compt lamp switch connector breakout (4-door) (left rear comb lamp pigtail) (left side of dash) junction block (m/t) (main harness, approx 2cm from bulkhead grommet near master cyl) (main harness, approx 4cm from stoplamp switch connector breakout) (right rear comb lamp pigtail) 2 door 4 door Anti-lock brakes system Back fuse 15a Center high- mounted stoplamp Center of hatchback door, near rear wiper motor g410 Combination switch G100 (lh front engine compt, on left front inner fender near G101 (right front inner fender) G202 G202 (left side of dash) G202 (under left side of dash) G407 (near deck lid striker) G407 (rear center of luggage compt, near deck lid striker) Haz fuse 15a Hazard switch Head Hot at all times Hot in on and start Instrument cluster Interior lights system Junction block Junction block (behind left side of dash) Left front park/turn lamp Left parking lamp Left rear combination lamp Left stop lamp Left turn ind License plate lamp Light 1 relay (relay box) Light switch Off Park Right front park/turn lamp Right parking lamp Right rear combination lamp Right stop lamp Right turn ind S100 S102 S113 S117 S204 S206 S240 S256 S302 (floor harness, approx 5cm from center console branch breakout) S402 (2-door) s407 (4-door) S404 S405 S410 (2 door) S411 S412 S413 Side marker lamp (2 door) Stop fuse 15a Stoplamp switch (top of brake pedal) Tail fuse 15a Tail/ stop lamp Turn lamp Turn relay Turn signal switch
GROUND DISTRIBUTION Ground Distribution Wiring Diagram (1 of 3) for Chevrolet Metro LSi 1998 List of elements for Ground Distribution Wiring Diagram (1 of 3) for Chevrolet Metro LSi 1998: 51 c1 (main harness, approx 8cm from bulkhead grommet, near master cylinder) (with abs) lamp driver relay A/c 2 relay (condenser A/c amplifier Battery Braid Brake fluid level switch Camshaft position sensor Crankshaft position sensor shield D c2 Daytime running lamps control module Distributor shield Electronic brake control module Engine fan motor Fan) From j/b (diagram 2 of 3) Front washer pump G100 (lh front engine compartment, on lh front inner fender near battery) G108 (lh front engine compartment, front of battery) G130 (mounted on top lh side of transaxle) G131 (center rear of engine,on intake manifold) G200 (behind left kick panel) Heated oxygen sensor #1 shield Heated oxygen sensor 2 shield Horn Idle air control valve Idle speed control motor Ignition ccoil no 1 Ignition ccoil no 2 Left front turn lamp Left parking lamp Light 2 relay Powertrain control module Rear washer pump Relay box S113 (main harness, approx 6cm from left front turn lamp connector breakout) S115 (main harness, near rear washer pump) S130 engine harness, near generator connector breakout) S165 (engine harn, near starter breakout) S207 (main harness, approx 15cm from g200) S208 (main harness, 2cm from junction block connector c8 breakout) S209 S210 (main harness, left side of dash) S213 (main harn, near master cylinder) S247 (main harness, left rear of engine compt)) S248 (engine harn, at pcm branch breakout) S263 (engine harn, at pcm branch breakout) To s111 (diagram 2 of 3) Vin 2 W/ abs Ground Distribution Wiring Diagram (2 of 3) for Chevrolet Metro LSi 1998 List of elements for Ground Distribution Wiring Diagram (2 of 3) for Chevrolet Metro LSi 1998: 57 (4-door) (i/p harness, approx 5cm from cigar lighter connector breakout) s243 (not used) (with a/c) a/c switch A/c condenser fan Audio alarm module Blower motor C210 Center high mounted stop lamp Cigar lighter Combination switch Data link connector on-board diagnostic ii Data link connector- on-board diagnostic ii Dimmer switch Dome lamp Dual pressure switch Duty check data link connector Early fuel evaporation heater From g131 (diagram 1 of 3) Front wiper/ washer switch G101 (rh front engine compartment, on right front inner fender) G131 (center rear of engine) G202 (left side of dash) G206 (right center of dash, behind radio) G410 (2-door) (center of hatchback door, near rear wiper motor) Ignition control module Ignition switch Illumination controller Instrument panel cluster assembly Junction block Left power door lock switch Light switch Noise suppressor filter Power door lock control module Radio Rear defogger switch Rear wiper motor Red Right front park/turn lamp Right parking lamp Right power door lock switch S111 (main harness, near ignition coil connector breakout) S117 (main harn, near g101 breakout) S134 (engine harn, 22cm from bulkhead grommet, center of firewall) S167 (engine harn, right rear of engine compt) S235 (i/p harness, left side of dash) S236 (i/p harness, 8cm from i/p cluster c3 breakout) S237 (i/p harness, 10cm from radio conn breakout) S238 (i/p harn, near blower motor breakout) S239 (i/p harness, approx 11cm from i/p cluster c3 breakout) S240 (i/p harness, approx 6cm from dlc-obd ii breakout) S245 (i/p harn, 12cm from dash cluster breakout) S254 (i/p harness, center of dash) S314 (floor harn, left side of dash) To s209 (diagram 1 of 3) Turn relay Vin Ground Distribution Wiring Diagram (3 of 3) for Chevrolet Metro LSi 1998 List of elements for Ground Distribution Wiring Diagram (3 of 3) for Chevrolet Metro LSi 1998: 30 (floor harness, approx 20cm from center console branch breakout) s301 (floor harness, approx 20cm from left rear combination lamp conn breakout) s407 (floor harness, approx 5cm from left rear combination lamp connector breakout) s402 2 door 4 door Below right rear seat) Center high mounted stop lamp Forward discriminating sensor Fuel assembly unit Fuel sender assembly G203 (behind right kick panel) G407 (rear center of lug- gage compartment, near deck lid striker) G411 (2-door) (left side of hatch- back door, behind trim panel) G413 (4-door) (behind right rear quarter trim panel) Left rear combination lamp License plate lamp Rear defogger Red Right rear combination lamp S311 (floor harness, approx 10cm from breakout to luggage compartment harness) S315 (fuel tank jumper harness, S403 (floor harness, approx 5cm from g407 breakout) S406 (floor harness, approx 10cm from left rear combination lamp connector breakout) S408 (floor harness) S411 (right rear combination lamp pigtail, approx 6cm from grommet at right rear of trunk) S413 (left rear combination lamp pigtail, approx 6cm from grommet at left rear of trunk) Seat belt switch Sensing and diagnostic module Shift lock solenoid Under right rear seat)
HEADLIGHTS Headlight Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Headlight Wiring Diagram for Chevrolet Metro LSi 1998: 47 (main harn, left rear of engine compt) s104 (main harness, right rear of engine compt) s107 Anti-lock brakes systems Brake ind C5 red Charge in Combination switch Daytime running lamps control module (behind left side of dash) Daytime running lamps diode Daytime running lamps ind Dimmer switch Drl indic G200 (behind left kick panel) G202 (left side of dash) Ground H/l, l fuse 15a H/l, r fuse 15a Hdlmps on in Head High beam ind Hot at all times Hot in on and start Ig-coil fuse 15a Ignition Instrument panel cluster assembly Junction block (left side of dash) Left headlamp Light 2 relay Light switch Low beam Off Park Park brake Parking brake switch Pass Red Relay box (on left side of engine compt, behind battery) Right headlamp S105 (main harn, near evap canister conn breakout) S202 S205 (main harn, approx 1cm from grommet at left rear of engine compt) S207 S210 S223 (main harn, approx 10cm from grommet at left rear of engine compt) S242 S246 Starting/ charging system
HORN Horn Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Horn Wiring Diagram for Chevrolet Metro LSi 1998: 9 G100 (left front engine compartment, on left front inner fender, near battery) Haz fuse 15a Horn Horn relay Hot at all times Junction block (behind left side of dash) Left horn switch Right horn switch S113
INSTRUMENT CLUSTER Instrument Cluster Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Instrument Cluster Wiring Diagram for Chevrolet Metro LSi 1998: 83 (center rear of engine) (m/t only) 1.3l vin 9 only A10 A11 A12 A13 A14 A15 A16 A16 c1 Abs active ind Abs ind Accy Air bag ind Anti-lock brakes system B10 B10 c2 Brake fluid level switch (in brake fluid reservoir) Brake ind C1 b5 C10 C11 C12 C13 C13 c3 Charge ind Ctrl Data link connector (behind right side of dash) Daytime running lamps control module (behind left side of dash) Defogger ind Defogger system Drl ind Duty check Electronic brake control module (behind left side of dash, above junction block) Engine controls system Engine coolant temperature gage Engine coolant temperature sensor (on rear of engine, in t'stat housing) Exterior lights system Fuel gage sending unit (in fuel tank) Fuel gauge Fuel lvl sig G100 (lh front engine compt, on lh front inner fender, near battery) G131 G202 (left side of dash) G407 (rear center of luggage compt, near deck lid striker) Headlights system High beam ind Hot in on and start Ig-coil fuse 15a Ignition switch Illumination (2 bulbs) Ind ctrl Instrument panel cluster assembly Interior lights system Junction block Junction block (on left side of dash) Left turn ind Lock Malfunction ind Off Oil pressure ind Oil pressure switch (left side of engine, above oil filter) Parking brake switch (under floor console, on parking brake lever base) Powertrain control module (behind right side of dash, near glove box) Red Right turn ind S213 S223 (main harn, left rear of engine compt) S226 (dash harn, approx 2cm from cluster connector c3 breakout) S240 S242 S245 S261 (engine harn, 4cm from pcm connectors breakout) S315 Seat belt ind Signal Start Starting/charging system Tachometer Upshift ind (m/t) Vehicle speed sensor Warning system
INTERIOR LIGHTS Interior Light Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Interior Light Wiring Diagram for Chevrolet Metro LSi 1998: 56 (4-door) (i/p harn, behind left side of dash) s217 (i/p harness, approx 4 cm from data link connector- on board diagnostics ii breakout) s252 (i/p harness, approx 6 cm from diode module connector breakout) (left side of dash) junction block (main harness, approx 2 cm from bulkhead grommet near master cylinder) s204 (not used) (not used) (right side of dash, behind radio) 2-door Audio alarm module (behind dash, left of steering column) Bulbs C10 Combination switch Diode no 1 (near audio alarm module) Dome fuse 15a Dome lamp Door Engine controls system Exterior lights system G202 G206 Ground Head Heater control unit illumination lamp Hot at all times Illumination controller Instrument panel cluster assembly Junction block (behind left side of dash) Junction block (on left side of dash) Left front door jamb switch Light 1 relay (on relay box) Light switch Luggage compartment lamp Luggage compartment lamp switch Manual selector lever illumination lamp (a/t) Off Park Power Radio Rear defogger switch Rear wiper/washer switch S218 (i/p harness, approx 3 cm from i/p cluster c3 breakout) S219 (i/p harn, behind left side of dash) S221 (i/p harness, approx 7 cm from i/p cluster c2 breakout) S222 S228 (i/p harness, behind left side of dash) S229 (i/p harness, approx 4 cm from i/p cluster c1 breakout) S230 (i/p harness, 13 cm from i/p cluster c3 breakout) S239 S254 S302 (floor harn, behind left side of dash) S310 (floor harness, approx 6 cm from junction block conn breakout) S419 (floor harness, approx 21 cm from right rear door jamb sw conn breakout) Tail fuse 15a Warning system
POWER DISTRIBUTION Power Distribution Wiring Diagram (1 of 2) for Chevrolet Metro LSi 1998 List of elements for Power Distribution Wiring Diagram (1 of 2) for Chevrolet Metro LSi 1998: 56 (m/t) (a/t) (main harness, approx 5cm from relay box breakout) s151 (main harness, at relay box) s122 (main harness, left side of dash) s256 (main harness, near master cylinder) s244 (main harness, near master cylinder) s246 (not used) A/c 1 relay A/c 2 relay A/c fuse 15a Abs fuse 40a B12 Bat Batt fuse 70a Battery Data link connector- on-board diagonstics ii Daytime running lamps diode Dome fuse 15a Dome lamp Door lock fuse 20a Efe htr relay Electronic brake control module Electronic brake control relay Fi fuse 15a Fuse box (left side of engine compt, behind battery) Generator Haz fuse 15a Hazard switch Hl-l fuse 15a Hl-r fuse 15a Horn relay Ig fuse 60a Ignition key warning switch Instrument panel cluster assembly Junction block (left side of dash) Lamp fuse 40a Left headlamp Light 1 relay Luggage compartment lamp Main relay Power door lock control module Powertrain control module Ptc fuse 30a Radio Rdtr fan relay Rdtr fuse 30a Relay box Relay box (left side of engine compt, behind battery) Right headlamp S222 (i/p harness, approx 6cm from dlc breakout) Starter solenoid Stop fuse 15a Stoplamp switch Tail fuse 15a To ignition switch (diagram 2 of 2) Turn signal/ combination switch Power Distribution Wiring Diagram (2 of 2) for Chevrolet Metro LSi 1998 List of elements for Power Distribution Wiring Diagram (2 of 2) for Chevrolet Metro LSi 1998: 63 (engine harn, center of firewall) s126 (engine harn, near generator breakout) (i/p harn, approx 6cm from dlc breakout) s224 (i/p harness, 5cm from cluster conn breakout) s241 (i/p harness, at cluster conn breakout) s242 (main harn, 8cm from junction block breakout) s202 (main harn, center of firewall) s152 (main harness, approx 10cm from breakout to i/p harn) s215 (main harness, near master cylinder) s100 A/c 1 relay A/c amplifier A/t Acc Acc fuse 15a Air bag fuse 15a Audio alarm module Back fuse 15a Backup lamp switch (m/t) transaxle range switch (a/t) Blower speed selector switch Camshaft position sensor Cigar lighter Clutch pedal position switch Daytime running lamps control module Def fuse 20a Electronic brake control module Electronic brake control relay From junction block (diagram 1 of 2) Front wiper motor Front wiper/ washer switch Fuel pump relay G206 (right center of dash) behind radio) Generator Hazard switch Heated oxygen sensor 1 Heated oxygen sensor 2 Htr fuse 20a Ig-coil fuse 15a Ignition coil (vin 6) Ignition coil 1 (vin 2) Ignition coil 2 (vin 2) Ignition switch Inflatable restraint sensing & diagnostics module Instrument panel cluster assembly Junction block (left side of dash) Lamp driver relay Lock M/t Noise suppressor filter (vin 6) Powertrain control module Radio Rdtr fan relay Rear defogger switch Rear wiper motor Rear wiper/ washer switch Relay box (left side of engine compt, behind battery) Run S101 (main harn, near master cylinder) S160 S161 Start Transaxle range switch Turn/ signal combination switch Wiper fuse 15a
POWER DOOR LOCKS Power Door Lock Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Power Door Lock Wiring Diagram for Chevrolet Metro LSi 1998: 25 (floor harness, approx 11cm from breakout to right front door) Door lock fuse 20a G202 Ground Hot at all times Junction block (left side of dash) Left front power door lock actuator Left front power door lock switch Left rear power door lock actuator Lock Lock in Lock out Pnk Power Power door lock control module (behind left side of dash on "a" pillar) Red Right front power door lock actuator Right front power door lock switch Right rear power door lock actuator S307 S308 (floor harn, approx 19cm from breakout to right front door) S314 Unlock Unlock in Unlock out
RADIO Radio Wiring Diagrams for Chevrolet Metro LSi 1998 List of elements for Radio Wiring Diagrams for Chevrolet Metro LSi 1998: 31 Acc fuse 15a Antenna Dome fuse 15a G206 (right center of dash, behind radio) Ground Hot at all times Hot in acc or run Interior lights system Junction block (on left side of dash) Lcd dim cntrl Lcd input Left front speaker Left rear speaker Lf speaker (+) Lf speaker (-) Lr speaker (+) Lr speaker (-) Memory power Nca Radio Radio power Red Rf speaker (+) Rf speaker (-) Right front speaker Right rear speaker Rr speaker (+) Rr speaker (-) S222 S224 S237
SHIFT INTERLOCKS Shift Interlock Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Shift Interlock Wiring Diagram for Chevrolet Metro LSi 1998: 14 (rear center of luggage compt, near deck lid striker) 2 door 4 door Back fuse 15a Engine controls system G407 Hot in on & start Junction block (behind left side of dash) S158 (engine harn, near generator) S301 S311 Shift lock solenoid (under floor console, in front of shift lever) Stoplamp switch (top of brake support) Transaxle range switch (top of transaxle)
STARTING/CHARGING Charging Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Charging Wiring Diagram for Chevrolet Metro LSi 1998: 24 (1997) (1998, 99) (engine harn, 10 cm from bulkhead grommet) s162 Acc Batt fuse 70a Battery Charge indicator Daytime running lamps control module (behind left side of dash) Fuse box (left side of engine compt, behind battery) G108 (left front of engine compt, front of battery) G130 (top left side of transaxle) Generator Ig fuse 60a Ig-coil fuse 15a Ignition switch Instrument panel cluster assembly Junction block (left side of dash) Lock Run S160 S203 (1cm from bulkhead grommet) S242 Start Starter solenoid Starting Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Starting Wiring Diagram for Chevrolet Metro LSi 1998: 19 A/t Acc Batt fuse 70a Battery Clutch pedal position switch (above clutch pedal) Engine controls system Fuse box (left side of engine compt, behind battery) G108 (left front of engine compt, front of battery) G130 (top left side of transaxle) Ig fuse 60a Ignition switch Junction block (left side of dash) Lock M/t S127 (engine harn, approx 8cm from breakout to starter solenoid) Start Starter Starter solenoid Transaxle range switch (top of transaxle)
SUPPLEMENTAL RESTRAINTS Supplemental Restraint Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Supplemental Restraint Wiring Diagram for Chevrolet Metro LSi 1998: 37 (center rear of luggage compt) (dash harn, near breakout to c200, left side of dash) s227 (dash harn, near breakout to cluster) (floor harn, near console branch breakout-2 door, near breakout to trunk harness-4 door) Air bag fuse 15a Airbag indicator Data line Data link connector obd-ii (under left side of dash) Discrim sens Driver high Driver low G203 (right kick panel) G407 Ground Hot in on or start Ig-coil fuse 15a Ign pos volt Ind ctrl Inflatable restraint forward discriminating sensor (front center of grille) Inflatable restraint i/p module (above glove box) Inflatable restraint sensing and diagnostic module (behind center console) Inflatable restraint steering wheel module (center of steering wheel) Instrument panel cluster assembly Junction block (left side of dash) Pass high Pass low Red S242 (dash harn, near breakout to cluster) S249 S301 (2 door) s311 (4 door) Seat belt switch Shorting bar Sir contact coil (part of turn signal/ combination switch) Sir data line Sir data link connector (behind left side of dash) St belt sw Warning systems
TRANSMISSION
1.3L 1.3L (VIN 2), Transmission Wiring Diagram, 3-Speed Transmission for Chevrolet Metro LSi 1998 List of elements for 1.3L (VIN 2), Transmission Wiring Diagram, 3-Speed Transmission for Chevrolet Metro LSi 1998: 63 "2" position signal "d" position signal "l" position signal "n" position signal "p" position signal "r" position signal (dash harn, near breakout to cluster assy) (engine harn, near engine compt grommet) 2nd brake solenoid 2nd brake sol ctrl Acc Air conditioning, headlights (drl), & engine controls system Audio alarm module Automatic transmission Back fuse 15a Direct clutch sol ctrl Direct clutch solenoid Dome fuse 15a Engine controls system Engine start signal Exterior lights system G133 (center rear of engine) G407 (center rear of trunk) Gauges/ indicators Ground Hazard switch Hot at all times Hot in on or start Ig-coil fuse 15a Ignition Ignition switch (right side of steering column) Instrument cluster Interior lights system Junction block (left side of dash) Lock Malfunction indicator lamp Memory power Mil ctrl Powertrain control module (behind right side of dash) Red Reference voltage Run S127 (engine harn, near firewall grommet) S130 S154 (engine harn, near firewall grommet) S156 (engine harn, near firewall grommet) S158 S164 (engine harn, 8 cm from map sensor breakout) S241 S242 S248 S259 (engine harn, near firewall grommet) Sensor ground Shift lock solenoid (under floor console, in front of shift lever) Start Starting/ charging system Stoplamp switch (top of brake pedal) Throttle position in Throttle position sensor (on side of throttle body) Transaxle range switch (top of transaxle) Vehicle speed sensor (top of transaxle) Vss hi (signal) Vss lo (ground) 1.3L VIN 2, A/T Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for 1.3L VIN 2, A/T Wiring Diagram for Chevrolet Metro LSi 1998: 63 "2" position signal "d" position signal "l" position signal "n" position signal "p" position signal "r" position signal (dash harn, near breakout to cluster assy) (engine harn, near engine compt grommet) 2nd brake solenoid 2nd brake sol ctrl Acc Air conditioning, headlights (drl), & engine controls system Audio alarm module Automatic transmission Back fuse 15a Direct clutch sol ctrl Direct clutch solenoid Dome fuse 15a Engine controls system Engine start signal Exterior lights system G133 (center rear of engine) G407 (center rear of trunk) Gauges/ indicators Ground Hazard switch Hot at all times Hot in on or start Ig-coil fuse 15a Ignition Ignition switch (right side of steering column) Instrument cluster Interior lights system Junction block (left side of dash) Lock Malfunction indicator lamp Memory power Mil ctrl Powertrain control module (behind right side of dash) Red Reference voltage Run S127 (engine harn, near firewall grommet) S130 S154 (engine harn, near firewall grommet) S156 (engine harn, near firewall grommet) S158 S164 (engine harn, 8 cm from map sensor breakout) S241 S242 S248 S259 (engine harn, near firewall grommet) Sensor ground Shift lock solenoid (under floor console, in front of shift lever) Start Starting/ charging system Stoplamp switch (top of brake pedal) Throttle position in Throttle position sensor (on side of throttle body) Transaxle range switch (top of transaxle) Vehicle speed sensor (top of transaxle) Vss hi (signal) Vss lo (ground)
WARNING SYSTEMS Warning System Wiring Diagrams for Chevrolet Metro LSi 1998 List of elements for Warning System Wiring Diagrams for Chevrolet Metro LSi 1998: 34 (2-door) (4-door) (near bulkhead connector) (on bulkhead, near master cylinder) Audio alarm module (right lower dash, below radio) Combination switch Dome fuse 15a Engine compartment relay box (left side of engine) Exterior lights system G202 (under left side of dash) G407 (rear center of luggage compt, near deck lid striker) Head Hot at all times Hot in on and start Ig-coil fuse 15a Ignition key warning switch Instr panel cluster assembly Interior lights system Junction block (behind left side of dash) Left front door jamb switch (left door frame) Light 1 relay Off park Red S204 S217 (right side of dash) S219 S227 (main harn, near junction block) S235 S241 S242 S256 S301 s311 Seat belt ind Seat belt switch Tail fuse 15a
WIPER/WASHER 2-Speed Wiper/Washer Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for 2-Speed Wiper/Washer Wiring Diagram for Chevrolet Metro LSi 1998: 15 Combination switch Front washer pump (bottom of washer fluid reservoir) Front wiper motor (right side of firewall) G100 (left front inner fender) High Hot in on and start Junction block (left side of dash) Off Park Run S115 Washer switch Wiper fuse 15a Wiper motor Wiper switch Intermittent Wiper/Washer Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Intermittent Wiper/Washer Wiring Diagram for Chevrolet Metro LSi 1998: 18 Combination switch Front washer pump (bottom of washer fluid reservoir) Front wiper motor (right side of firewall) G100 (left front inner fender) G202 (left side of dash) High Hot in on and start Int Inter- mittent controller Junction block (left side of dash) Off Park Run S115 Washer switch Wiper fuse 15a Wiper motor Wiper switch Rear Wiper/Washer Wiring Diagram for Chevrolet Metro LSi 1998 List of elements for Rear Wiper/Washer Wiring Diagram for Chevrolet Metro LSi 1998: 16 G100 (left front inner fender) G410 (center of hatchback door) Hot in on and start Interior lights system Junction block (left side of dash) Motor Off Park Rear washer pump (bottom of washer fluid reservoir) Rear washer switch Rear wiper motor (center of liftgate) Rear wiper switch Rear wiper/ washer switch Run S115 Wiper fuse 15a
