Diagram sections — 30 (46 total)
AIR CONDITIONING ANTI-LOCK BRAKES ANTI-THEFT BODY COMPUTER COMPUTER DATA LINES COOLING FAN CRUISE CONTROL DEFOGGERS ENGINE PERFORMANCE EXTERIOR LIGHTS GROUND DISTRIBUTION HEADLIGHTS HORN INSTRUMENT CLUSTER INTERIOR LIGHTS PASSIVE RESTRAINTS POWER ANTENNA POWER DISTRIBUTION POWER DOOR LOCKS POWER MIRRORS POWER SEATS POWER TOP/SUNROOF POWER WINDOWS RADIO STARTING/CHARGING SUPPLEMENTAL RESTRAINTS TRANSMISSION TRUNK, TAILGATE, FUEL DOOR WARNING SYSTEMS WIPER/WASHER
AIR CONDITIONING Air Conditioning Wiring Diagrams for Chrysler Sebring Limited 1998 List of elements for Air Conditioning Wiring Diagrams for Chrysler Sebring Limited 1998: 74 (internal to power distribution center) (internal to power distribution center) s103 (left strut tower) g102 (near breakout for map/iat sensor) (2.4l engine) (near fuel injector no.6 breakout) (2.5l engine) A/c compressor clutch A/c compressor clutch relay (in power distribution center) A/c evaporator temperature sensor (on right side of hvac housing) A/c heater control A/c heater control illum. A/c pres signal A/c press sig A/c pressure transducer (near compressor, attached to valve on discharge line) A/c switch A/c switch illum A/c switch sense Bi-level Blower motor resistor block (on lower right side of heater) Blower switch Blower switch illum Body control module (on junction block, under left side of dash) C12 C18 C21 C24 C26 C27 C28 C34 C35 C37 C57 C58 Ccd bus (+) Ccd bus (-) Defog led Defrost Evap temp sens sig Fuse 10a Fuse 30a Fuse 40a G206 (right center of dash) Ground Heat High High speed radiator fan relay (in power distribution center) Hot at all times Hot in run Hot in run or start Hot w/rear window defogger relay energized Hvac mode sense Interior lights system Junction block Low Low speed radiator fan relay (in power distribution center) Mix Mode door actuator (on left side of a/c-heater housing) Mode door driver Mode dr fbck sig Mode switch Mode switch illum Off Panel Power distribution center Powertrain control module (between air cleaner housing & power distribution center) Radiator fan motor assembly Red Relay control S106 S115 (near breakout for map/iat sensor) (2.4l engine) (near egr breakout) (2.5l engine) S116 Sens gnd Sensor gnd Sensor ground Tan
ANTI-LOCK BRAKES Anti-lock Brake Wiring Diagrams for Chrysler Sebring Limited 1998 List of elements for Anti-lock Brake Wiring Diagrams for Chrysler Sebring Limited 1998: 43 A10 A20 Abs lamp driver Abs warning lamp Battery Body control module (on junction block, under left side of dash) Ccd bus (+) Ccd bus (-) Controller anti-lock brake (right front inner fender) F12 Fuse 10 10a Fuse 19 40a Fuse 2 20a Fuse 4 20a Fuse 9 10a G19 Ground Hot at all times Hot in run or start Ignition Instrument cluster Junction block (under left side of dash) L50 Left front wheel speed sensor (attached to left knuckle boss) Left rear wheel speed sensor (attached to left brake support plate) Lt ft whl spd (+) Lt ft whl spd (-) Lt rear whl (+) Lt rear whl (-) Power distribution center (on left front inner fender) Right front wheel speed sensor (attached to right knuckle boss) Right rear wheel speed sensor (attached to right brake support plate) Rt ft whl spd (+) Rt ft whl spd (-) Rt rear whl (+) Rt rear whl (-) S105 S106 S140 S141 Stop lamp sw Stop lamp switch (top of brake pedal) Transmission control module (left front inner fender)
ANTI-THEFT Anti-theft Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Anti-theft Wiring Diagram for Chrysler Sebring Limited 1998: 64 (dash harn, in breakout to bcm) tan Arm Body control module C10 Ccd bus (+) Ccd bus (-) Combination flasher (part of multi-function switch) Ctsy lamps relay control Datalink connector (left of steering column, bottom of dash) Disarm Door ajar switch sense Dr ajar sense Fuse (b+) Fuse 10a Fuse 20a G103 (top of right front strut tower) G200 (left kick panel) G406 (on left side of trunk lid) G69 G71 G72 G73 G74 G75 Hdlmp relay control Headlights system (headlamp delay relay) High note horn (right front fender) Horn relay Horn relay control Horns system (horn switches) Hot at all times Hot in run or start Immobilizer (on steering column, near ign switch) Instrument cluster Interior lights system (illuminated entry relay) Junction block (under left side of dash) Lamp driver Left front door ajar switch Left front door arm/ disarm switch Low note horn (right front fender) Lt dr arm/ disarm sense Off Pnk Pnk/ red Pnk/red Power distribution center (on left front inner fender) Powertrain control module (between air cleaner housing and power dist center) Right front door ajar switch Right front door arm/ disarm switch Rt dr arm/ disarm sense S111 S132 S133 S301 S305 S400 S401 Seat belt control module (rear of console) Tan Tan/pnk Tan/red Trunk key cylinder switch Trunk lock cyl sense Vehicle theft security system set l.e.d.
BODY COMPUTER
COMPUTER DATA LINES Computer Data Lines for Chrysler Sebring Limited 1998 List of elements for Computer Data Lines for Chrysler Sebring Limited 1998: 29 (left front inner fender, in breakout for pcm conn) s132 (on top of engine, in breakout to ignition coil) s133 Airbag control module (under floor console) Body control module Ccd bus (+) Ccd bus (-) Controller anti-lock brake (right front inner fender) D20 D21 Data link connector (left side of steering column) Fuse 5 10a G200 (left kick panel) Gnd Hot at all times Immobilizer (1998 only) Instrument cluster Junction block (under left side of dash) Only Powertrain control module (left front of engine compt) Radio (w/ premium sound only) S127 (left front of engine compt, near breakout for pdc) S134 S140 (1998 only) S141 (1998 only) Sci receive Sci transmit Transmission control module (left front inner fender) W/ premium sound only Z11
COOLING FAN Cooling Fan Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Cooling Fan Wiring Diagram for Chrysler Sebring Limited 1998: 17 (internal to power distribution center) s106 C24 C27 Fuse 10a Fuse 40a G102 (left strut tower) High speed rad fan rly ctrl High speed radiator fan relay (in power distribution center) Hot at all times Hot in run or start Low speed rad fan rly ctrl Low speed radiator fan relay (in power distribution center) Power distribution center Powertrain control module (between air cleaner housing & power distribution center) Radiator fan motor assembly S103 (internal to power distribution center) S109 (left strut tower)
CRUISE CONTROL Cruise Control Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Cruise Control Wiring Diagram for Chrysler Sebring Limited 1998: 37 (engine harness, (engine harness, in pcm breakout) (top of left Body control module Brake sw sens Cancel Ccd bus (+) Ccd bus (-) Clock- spring Cruise engaged lamp Fuse 10a G102 strut tower) Ground Hot in run, off or start Ignition Instrument cluster Junction block K29 Nca On/ off On/off On/off sw sens Powertrain control module (between air cleaner housing and power distribution center) Res/ accel S109 S132 S133 in ignition coil breakout) Set/ coast Stop lamp switch (top of brake pedal) V27 V32 V35 V36 Vac ctrl sol Vehicle speed control servo (at left strut tower) Vehicle speed control/ horn switch Vent ctrl sol
DEFOGGERS Defogger Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Defogger Wiring Diagram for Chrysler Sebring Limited 1998: 23 A/c heater control Body control module C310 C7 c7 Defog led Fuse 10a Fuse 40a G200 (left kick panel) G206 (under right center of dash) G403 (right rear quarter panel) Hot at all times Hot in acc Junction block (left side of dash) Left power mirror Nca Or run Power distribution center (left front inner fender) Rear window defogger Rear window defogger relay Right power mirror S402 S403 Window defogger relay control
ENGINE PERFORMANCE
2.4L 2.4L, Engine Performance Wiring Diagrams (1 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.4L, Engine Performance Wiring Diagrams (1 of 4) for Chrysler Sebring Limited 1998: 83 (engine harness, in injector breakout) s114 (engine harness, near breakout for starter motor) s118 (near a/c compressor) a/c pressure transducer (on rear side of front bumper beam) battery temperature sensor (top of left front strut tower) (top of right front strut tower) A142 Asd rly out Asd rly output Batt temp sensor sig Body control module Ccd bus (+) Ccd bus (-) Ckp sensor sig Cmp sensor sig Cyl no.1 Cyl no.2 Cyl no.3 Cyl no.4 Double start o/d Ect sensor sig Egr sol control Engine coolant temperature sensor (on top left front of engine) F12 Fuel injectors (on top of engine) Fuse 11 10a Fused ign sw output (off/run/start) G102 G102 (top of left front strut tower) G103 Gen field driver Generator Gnd Heated oxygen sensor (ho2s) (downstream) (on rear of catalytic converter) Heated oxygen sensor (ho2s) (upstream) (on exhaust manifold) Hot in off, run or start Iat signal Ign coil no.1 Ign coil no.1 Ign coil no.2 Ignition (run/start) Ignition coil pack (top of valve cover) Inj no.1 driver Inj no.2 driver Inj no.3 driver Inj no.4 driver Instrument cluster Junction block (left side of dash) K11 K12 K13 K14 K17 K19 K20 K21 K22 K24 K35 K41 K42 K44 K90 Knk sensor sig Malfunction ind (chk eng lp ctrl) Malfunction indicator lamp (check engine) Map sensor sig Nca Powertrain control module (between air cleaner housing & power distribution center) S101 S109 S111 S131 (engine harness, pcm breakout) S132 (engine harness, in pcm connector breakout) S133 (engine harness, in ignition coil breakout) Sc on/off sw Sensor gnd Tan To spark plugs Tp sensor signal Upstrm htd ox sig V32 Z12 2.4L, Engine Performance Wiring Diagrams (2 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.4L, Engine Performance Wiring Diagrams (2 of 4) for Chrysler Sebring Limited 1998: 40 (engine harness, inside pdc) (engine harness, near map/ iat sensor breakout) s115 (engine harness, near map/iat sensor breakout) s116 (engine harness, near noise suppressor breakout) s124 (engine harness, near pcm breakout) Acc Automatic shut down relay (10) Camshaft position sensor (at rear of cylinder head) Ckp sensor signal Cmp sensor signal Crankshaft position sensor (on engine block, above oil filter) Electronic egr transducer solenoid (at right rear of cylinder head) Fuse 10a Fuse 4 20a Fuse 5 20a Fuse 8 20a Hot at all times Ignition switch Intake air temperature sensor (on intake manifold plenum) Knock sensor Lock Manifold absolute pressure sensor (on intake manifold plenum) Off Power distribution center (on left front inner fender) Red Red/ tan Run S102 S104 S105 S106 S110 S117 (engine harness, near cam sensor breakout) S120 S121 (engine harness, in pcm breakout) S130 (engine harness, near pcm connector breakout) Sensor gnd Start Tan Throttle position sensor (on throttle body) 2.4L, Engine Performance Wiring Diagrams (3 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.4L, Engine Performance Wiring Diagrams (3 of 4) for Chrysler Sebring Limited 1998: 45 (left front of trunk) (on left side of trunk lid) A/c compressor clutch relay (7) Ckp sensor signal Coil Cont- acts D21 Engine starter motor relay (9) Fuel pump module (in fuel tank) Fuel pump relay (3) G400 G406 High speed radiator fan relay (12) K22 K24 Low speed radiator fan relay (11) Nca Noise suppressor P/n Pnp switch sense Power distribution center (on left front inner fender) Red Red/tan S301 Sc on/off sw sense Sc sw signal Sc vac. sol. control Sc vent sol. control Sci transmit Sensor gnd Stop lamp sw sense Stop lamp switch (top of brake pedal) T10 T41 Tan Tan/ red Tan/red Torque req sense Tps signal Trans sci receive Transmission control module (on left front inner fender) Transmission range switch (front of transmission) Vehicle speed control servo (on left strut tower) Vehicle speed control/horn switch Vss signal 2.4L, Engine Performance Wiring Diagrams (4 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.4L, Engine Performance Wiring Diagrams (4 of 4) for Chrysler Sebring Limited 1998: 87 (engine harness, near pdc breakout) (left kick panel) (top of left front strut tower) A/c comp rly ctrl A/c press sig A14 A21 Auto shut dn rly Batt temp sns sig Body control module C18 C24 C27 C28 Ccd bus (+) Ccd bus (-) D20 D21 Data link connector (left of steering column, bottom of dash) Dnstrm htd ox sig Duty cycle evap/purge solenoid (on right strut tower) Evap/prge sol ctrl Fuel lvl sensor sig Fuel pmp rly ctrl Fuse 5 10a Fused b (+) G102 G200 G200 (left kick panel) Gnd Gnd High spd rly ctrl Iac driver no.1 Iac driver no.2 Iac driver no.3 Iac driver no.4 Iac motor no.1 driver Iac motor no.2 driver Iac motor no.3 driver Iac motor no.4 driver Idle air control motor (on throttle body assembly) Junction block (left side of dash) K10 K106 K107 K108 K118 K141 K29 K31 K39 K40 K51 K52 K59 K60 Leak pmp sol ctrl Leak pmp sw sense Linear purge sense Low spd rly ctrl P/s press sw sense Pnp sw sense Power steering pressure switch (mounted to power steering gear) Powertrain control module (between air cleaner housing & power distribution center) Red/tan S101 S127 S132 (engine harness, pcm conn breakout) S133 (engine harness, ignition coil breakout) S134 (engine harness) Sc sw signal Sc vac sol ctrl Sc vent sol ctrl Sci receive Sci transmit Sensor gnd Stop lp sw sense T10 T41 Torque req sense V35 V36 V37 Vapor canister leak detection pump (under right front headlamp) Vss signal Z11 Z12
2.5L 2.5L, Engine Performance Wiring Diagrams (1 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.5L, Engine Performance Wiring Diagrams (1 of 4) for Chrysler Sebring Limited 1998: 87 (eng harn, fuel rail harness) s123 (engine harness, between inj 2 & 4) (engine harness, near ect sensor breakout) s118 (on rear side of front bumper) battery temperature sensor (right front of engine) a/c pressure transducer (top of left front strut tower) (top of right front strut tower) A142 Asd rly out Asd rly output Body control module Ccd bus (+) Ccd bus (-) Ckp sensor sig Cmp sens sig Cmp sensor sig Cyl no.1 Cyl no.2 Cyl no.3 Cyl no.4 Cyl no.5 Cyl no.6 Distributor Double start override Ect sensor sig Egr sol control F12 Fuel injectors (on top of engine) Fuse 11 10a Fused ign sw output (off/run/start) G102 G102 (top of left front strut tower) G103 G110 (top left front of engine) Gen field driver Gnd Gnd sensor Heated oxygen sensor (ho2s) (downstream) (on rear of catalytic converter) Heated oxygen sensor (ho2s) (upstream) (on exhaust manifold) Hot in off, run or start Iat sensor signal Ign coil no.1 Ign coil no.1 driver Ignition (run/start) Inj no.1 driver inj no.6 driver inj no.5 driver Inj no.2 driver Inj no.3 driver Inj no.4 driver Instrument cluster Junction block (left side of dash) K11 K12 K127 K13 K14 K19 K20 K21 K22 K24 K35 K38 K41 K44 K58 K90 Malfunction ind (chk eng lp ctrl) Malfunction indicator lamp (check engine) Map sensor sig Nca Powertrain control module (between air cleaner housing & power distribution center) S101 S109 S111 S114 S132 (engine harness, pcm connector breakout) S133 (engine harness, near ignition coil breakout) Sc on/off sw Sensor gnd Sig sensor batt temp Tan To spark plugs Tp sensor signal Upstrm htd ox gnd Upstrm htd ox sig V32 Z12 2.5L, Engine Performance Wiring Diagrams (2 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.5L, Engine Performance Wiring Diagrams (2 of 4) for Chrysler Sebring Limited 1998: 45 (eng harn, inside pdc) (engine harness, inside pdc) (engine harness, near inj 6 breakout) s116 (engine harness, near pcm breakout) Acc Asd rly output Automatic shut down relay (10) Ckp sensor signal Crankshaft position sensor (on rear of transmission housing, on differential housing) Electronic egr transducer solenoid (on left exhaust of manifold, near rear of engine) Engine coolant temperature sensor (near thermostat housing) Fuse 10 10a Fuse 10a Fuse 4 20a Fuse 5 20a Fuse 8 20a Fuse 9 10a Gen field driver Generator Hot at all times Ignition switch Intake air temperature sensor (on intake manifold plenum) Lock Manifold absolute pressure sensor (on intake manifold plenum) Near pcm connector breakout) Off Power distribution center (on left front inner fender) Red Red/ tan Red/tan Run S102 S104 S105 S106 S110 S115 (engine harness, near egr breakout) S120 S121 (engine harness, in pcm break- out) S124 (engine harness, near distributor breakout) Sensor gnd Start Tan Throttle position sensor (on throttle body) Tp sensor signal 2.5L, Engine Performance Wiring Diagrams (3 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.5L, Engine Performance Wiring Diagrams (3 of 4) for Chrysler Sebring Limited 1998: 42 (left front of trunk) (on left side of trunk lid) A/c compressor clutch relay (7) Ckp sensor signal Coil Cont- acts D21 Engine starter motor relay (9) Fuel pump module (in fuel tank) Fuel pump relay (3) G400 G406 High speed radiator fan relay (12) K22 K24 Low speed radiator fan relay (11) Nca Pnp switch sense Power distribution center (on left front inner fender) Red Red/tan S301 Sc on/off sw sense Sc sw signal Sc vac sol control Sc vent sol control Sci transmit Sensor gnd Stop lamp sw sense Stop lamp switch (top of brake pedal) T10 T41 Tan Tan/ red Torque req sense Tps signal Trans sci receive Transmission control module (on left front inner fender) Transmission range switch (front of transmission) Vehicle speed control servo (on left strut tower) Vehicle speed control/horn switch Vss signal 2.5L, Engine Performance Wiring Diagrams (4 of 4) for Chrysler Sebring Limited 1998 List of elements for 2.5L, Engine Performance Wiring Diagrams (4 of 4) for Chrysler Sebring Limited 1998: 86 (engine harness, near pdc breakout) (left kick panel) (top of left front strut tower) A/c comp rly ctrl A/c press sig A14 A21 Auto shut dn rly Batt temp sns sig Body control module C18 C24 C27 C28 Ccd bus (+) Ccd bus (-) D20 D21 Data link connector (left side of steering column, bottom of dash) Dnstrm htd ox sig Duty cycle evap/purge solenoid (right strut tower) Evap/prge sol ctrl Fuel lvl sensor sig Fuel pmp rly ctrl Fuse 5 10a Fused b (+) G102 G200 G200 (left kick panel) Gnd Gnd High spd rly ctrl Iac driver no.1 Iac driver no.2 Iac driver no.3 Iac driver no.4 Iac no.2 driver Iac no.3 driver Iac no.4 driver Idle air control motor (on throttle body) Junction block (left side of dash) K10 K106 K107 K108 K118 K141 K29 K31 K39 K40 K51 K52 K59 K60 Leak pmp sol ctrl Leak pmp sw sense Linear purge sense Low spd rly ctrl P/s press sw sense Pnp sw sense Power steering pressure switch (mounted to power steering gear) Powertrain control module (between air cleaner housing, & power distribution center) Red/tan S101 S127 S133 (engine harness, ignition coil breakout) S133 (engine harness, pcm conn breakout) S134 (engine harness) Sc sw signal Sc vac sol ctrl Sc vent sol ctrl Sci receive Sci transmit Sensor gnd Stop lp sw sense T10 T41 Torque req sense V35 V36 V37 Vapor canister leak detection pump (under right front headlamp) Vss signal Z11 Z12
EXTERIOR LIGHTS Back-up Lamps Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Back-up Lamps Wiring Diagram for Chrysler Sebring Limited 1998: 12 Automatic day/night mirror Fuse 4 15a G406 (on trunk lid) Hot in run Junction block Left back-up lamp Rev sens Right back-up lamp S142 S404 S405 Transmission range switch (front of transmission) Exterior Lamps Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Exterior Lamps Wiring Diagram for Chrysler Sebring Limited 1998: 67 (in tail lamp) s406 (in tail lamp) s407 (top of brake pedal) stop lamp switch A15 Acc Body control module Center high mounted stop lamp Combination flasher Combined rear lighting module (left rear quarter panel) Fuse 12 40a Fuse 15 10a Fuse 4 20a Fuse 6 20a Fuse 7 20a Fuse 8 20a Fused b+ G102 (top of left front strut tower) G103 (top of right front strut tower) G200 (left kick panel) G400 (left front of trunk) G406 (on left side trunk lid) Ground Head Headlamp switch Hot at all times Ignition switch Instrument cluster Inter- mittent wiper switch Junction block L50 L60 L61 L62 L63 Left park/turn signal lamp Left side marker lamp Left tail & stop/ turn signal lamp Left tail/ stop/ turn signal lamp Left turn signal indicator License lamp Lock Lt turn Multi-function switch Off Park Pk lp sw out Pnk Power distribution center Red Right park/turn signal lamp Right side marker lamp Right tail & stop/ turn signal lamp Right turn signal indicator Rt turn Run S102 S111 S301 S404 S405 S408 (in tail lamp) S409 (in tail lamp) Seat belt control module Start Stop lp Tan Turn signal/ hazard warning switch
GROUND DISTRIBUTION Ground Distribution Wiring Diagram (1 of 2) for Chrysler Sebring Limited 1998 List of elements for Ground Distribution Wiring Diagram (1 of 2) for Chrysler Sebring Limited 1998: 54 (2.5l only) distributor (w/ premium radio only) power amplifier Auto- matic day/night mirror Autostick switch Battery Body control module Brake warning pressure switch C10 Controller anti-lock brake Data link connector Daytime running lamp module Downstream heated oxygen sensor From splice s308 (diagram 2 of 2) G102 (top of left front strut tower) G103 (top of right front strut tower) G129 (left rear of trans- mission) G200 (left kick panel) Headlamp switch High note horn Ignition switch Illuminated entry relay Immobilizer Instrument cluster Intermittent wiper relay Junction block Key-in switch Left fog lamp Left headlamp Left park/turn signal lamp Low note horn Nca Overhead map lamp Power distribution center Power steering pressure switch Powertrain control module Radiator fan motor assembly Right fog lamp Right headlamp Right park/turn signal lamp S101 (left strut tower) S109 (left strut tower) S111 (right strut tower) Seat belt control module Trans- mission relay Transmission control module Upstream heated oxygen sensor Vehicle speed control servo Washer fluid level switch Wind- shield wiper motor Windshield washer pump motor Z11 Z12 Z13 Z14 Ground Distribution Wiring Diagram (2 of 2) for Chrysler Sebring Limited 1998 List of elements for Ground Distribution Wiring Diagram (2 of 2) for Chrysler Sebring Limited 1998: 56 A/c- heater control Airbag control module Ash receiver lamp Body control module Center high mounted stoplamp Cigar lighter/ power outlet Combined rear lighting module Decklid solenoid Driver seat belt solenoid Fuel pump module G206 (under right center of dash) G302 (at base of gear shift) G400 (left front of trunk) G403 (right rear quarter panel) G406 (on left side of trunk lid) Glove box lamp Junction block Left back-up lamp Left door window motor relay Left power door lock switch Left power mirror Left side marker lamp Left tail and stop/turn signal lamps License lamp Master power window switch Nca Passenger seat belt solenoid Power antenna Power mirror switch Power seat switch Power top switch Power top up/down relays Prndl led Radio Rear window defogger Right back-up lamp Right door window motor relay Right power door lock switch Right power mirror Right side marker lamp Right tail and stop/turn signal lamps S200 (in breakout to cigar lighter) S301 (near breakout for combined rear lighting module) S308 (near breakout for courtesy lamp relay) S320 S402 (inside left door) S403 (inside right door) S404 (near breakout for back-up lamp) S405 (near rear lamps grommet) Seat belt control module Seat belt switch To g200 (diagram 1 of 2) Traveler Trunk key cylinder switch W/ vtss only Window timer module
HEADLIGHTS Headlamps/Fog Lamps Wiring Diagram, with DRL for Chrysler Sebring Limited 1998 List of elements for Headlamps/Fog Lamps Wiring Diagram, with DRL for Chrysler Sebring Limited 1998: 56 (convertible) (momentary switch) Body control module Brake warn lp Ccd bus (+) Ccd bus (-) Daytime running lamp module Dimm sw high beam output Dimm sw low beam output Flash to pass Fog lamp indicator Fog lamp switch Fuse 10 20a Fuse 11 10a Fuse 12 10a Fuse 13 20a Fuse 15 40a Fuse 2 10a Fuse 3 10a Fuse 4 15a Fuse 7 15a Fused b (+) G102 (left front strut tower) G103 (right front strut tower) G200 (left kick panel) Gnd Ground Hdlp delay rly ctrl Head Headlamp delay relay Headlamp dimmer switch Headlamp switch High High beam indicator lamp High beam indicator lamp ctrl High beam sense Hot at all times Hot in off, run or start Hot in run Ign Ignition Instrument cluster Junction block (under left side of dash) Left fog lamp Left headlamp Low Low beam output Off Park Park brake switch (on brake lever) Pnk/ red Power distribution center (on left front inner fender) Right fog lamp Right headlamp S109 S111 Headlamps/Fog Lamps Wiring Diagram, without DRL for Chrysler Sebring Limited 1998 List of elements for Headlamps/Fog Lamps Wiring Diagram, without DRL for Chrysler Sebring Limited 1998: 47 (convertible) (momentary switch) Body control module Ccd buss (+) Ccd buss (-) Dimm sw high beam output Dimm sw low beam output Flash to pass Fog lamp indicator Fog lamp switch Fuse 11 10a Fuse 12 10a Fuse 13 20a Fuse 15 40a Fuse 2 10a Fuse 3 10a Fuse 7 15a Fused b (+) G102 (left front dash tower) G103 (right front dash tower) G200 (left kick panel) Gnd Ground Hdlp delay rly ctrl Head Headlamp delay relay Headlamp dimmer switch Headlamp switch High High beam indicator lamp High beam indicator lamp ctrl Hot at all times Hot in off, run or start Ign Instrument cluster Junction block (under left side of dash) Left fog lamp Left headlamp Low Off Park Pnk/ red Power distribution center (on left front inner fender) Right fog lamp Right headlamp S109 S111
HORN Horn Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Horn Wiring Diagram for Chrysler Sebring Limited 1998: 15 Body control module Clockspring Fuse 8 20a G103 (top of right front strut tower) High note horn (right front fender) Horn relay Horn relay control Hot at all times Junction block (under left side of dash) Left horn switch Low note horn (right front fender) Nca Right horn switch S111 Vehicle speed control/ horn switch
INSTRUMENT CLUSTER Instrument Cluster Wiring Diagram (1 of 2) for Chrysler Sebring Limited 1998 List of elements for Instrument Cluster Wiring Diagram (1 of 2) for Chrysler Sebring Limited 1998: 83 (conn a) (conn b) A13 Abs warning lamp Air bag warning lamp Airbag warning lamp control B10 B11 B12 B13 Body control module Brake warning lamp Ccd bus (+) Ccd bus (-) Charging system warning lamp Charging system warning lamp control Cruise (vehicle speed control) engaged lamp control Cruise engaged lamp Decklid ajar switch sense Decklid warning lamp Decklid warning lamp control Door ajar indicator lamp Door ajar indicator lamp control Engine coolant temperature gauge Engine coolant temperature gauge control Engine coolant temperature lamp Engine coolant temperature lamp control Exterior lights system Fog lamp indicator Fuel gauge Fuel gauge control Fuse 11 10a Fuse 5 10a Fuse 7 20a Fuse 9 10a Fused (b+) Fused b(+) Fused ign Fused ignition switch input (off/run/start) G200 (left kick panel) G206 (behind center of dash) General illumination lamps Ground High beam indicator lamp High beam indicator lamp control Hot at all times Hot in off, run or start Hot in run or start Instrument cluster Junction block (under left side of dash) Left turn signal indicator Low fuel warning lamp Low fuel warning lamp control Low washer fluid lamp control Low washer warning lamp Malfunction indicator lamp (check engine) Malfunction indicator lamp control (check engine) Odometer Odometer control Oil pressure lamp Oil pressure switch (2.4l: right side of engine) (2.5l: side of engine, near oil filter) P r n d l Panel lamps driver Pnk Pnk/ red Pnk/red Power distribution center (left front inner fender) Prndl control Prndl indicator Right turn signal indicator S106 S200 Seat belt indicator lamp Seat belt indicator lamp control Speedometer Speedometer control Tachometer Tachometer control Traveler Trip odometer Trip odometer control Vehicle theft security system (vtss) set led Washer switch sense Instrument Cluster Wiring Diagram (2 of 2) for Chrysler Sebring Limited 1998 List of elements for Instrument Cluster Wiring Diagram (2 of 2) for Chrysler Sebring Limited 1998: 39 Abs warning lamp Acc Airbag control module (under floor console, near transmission selector) Body control module Brake pressure warning switch (on master cylinder) Ccd bus (+) Ccd bus (-) Controller anti-lock brake (right front fender apron) Data link connector (left side of dash) Daytime running lamps module (canadian models) Decklid ajar switch Fuel level sensor Fuel level sensor signal Fuel pump module (in fuel tank) G102 (left strut tower) G102 (right strut tower) G200 (left kick panel) G406 (on trunk lid) Ignition switch Junction block (under left side of dash) Lock Off Park brake switch (on park brake lever) Powertrain control module (between air cleaner housing and power distribution center) Run S101 S111 S132 (engine harn, near breakout to pcm) S133 (engine harn, in breakout to ign coil) S301 S304 (rear harn, near breakout to rear window defogger) S308 Seat belt switch (in seat belt buckle) Seat belt switch sense Start Transmission control module (left front inner fender) Trunk lamp Vtss indicator lamp driver Washer fluid level switch (top of reservoir)
INTERIOR LIGHTS Interior Light Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Interior Light Wiring Diagram for Chrysler Sebring Limited 1998: 69 (body harn, near left visor/vanity lamp breakout) (body harn, near map/ reading lamp breakout) (i/p harn, in body control module breakout) (not used) A/c heater control Ash Body control module C10 Dimmer signal E19 Exterior lights system Fuse 10a Fuse 20a G200 (left kick panel) G206 (under right center of dash) G38 G74 G75 Garage door opener lockout Glove box lamp Ground Ground distribution Halo lamp driver Head Headlamp switch Hot at all times Ill. entry ctrl Illuminated entry relay (behind dash, right of steering column) Instrument cluster Junction block (under left side of dash) Key-in halo lamp (right side of column) Lamp Left door courtesy lamp Left front door ajar switch Left front door sw Left visor/vanity lamp M112 M50 Nca Off Overhead map lamp Panel lamps driver Park Pnk Prndl illumination led Radio Rear floor courtesy lamp Receiver Red Right door courtesy lamp Right front door ajar switch Right front door sw Right visor/vanity lamp S134 S200 S302 S303 S304 (body harn, near rear window defogger feed breakout) S305 (i/p harn, in body control module breakout) S307 S308 S400 S401 Seat belt control module Tan Tan/pnk Trunk ajar switch (on latch) Trunk lamp Universal garage door opener
PASSIVE RESTRAINTS Passive Restraint Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Passive Restraint Wiring Diagram for Chrysler Sebring Limited 1998: 34 (left side of dash, in breakout for bcm) s305 A45 Acc/run Body control module Combination flasher Door ajar Driv latch Driver seat belt solenoid F13 Fuse 10a Fuse 20a Fused b(+) G200 (left kick panel) G302 (at base of gear shift) G74 G75 Gnd Ground Hot at all times Hot in acc and run Intermittent wiper switch Junction block (under left side of dash) Left door ajar switch Lf door ajar Lf door sw Pass latch Passenger seat belt solenoid Power distribution center (on left front inner fender) Rf door ajar Right door ajar switch S308 Seat belt control module (rear of console) Tan Tan/red
POWER ANTENNA Power Antenna Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Power Antenna Wiring Diagram for Chrysler Sebring Limited 1998: 14 12 volts-up 0 volts-down Coaxial antenna cable Fuse 10a Fused (b+) G403 (right rear quarter panel) Ground Hot at all times Junction block (left side of dash) Power amplifier (under passenger's seat) Power antenna (right rear of trunk) Radio Radio 12 volt input Radio 12 volt output W/premium radio
POWER DISTRIBUTION Power Distribution Wiring Diagram (1 of 2) for Chrysler Sebring Limited 1998 List of elements for Power Distribution Wiring Diagram (1 of 2) for Chrysler Sebring Limited 1998: 82 (not used) A/c comp- ressor clutch relay A14 A15 A24 A41 Acc Airbag control module Auto- matic shut- down relay Auto- stick switch Automatic day/night mirror Battery Blower motor resistor block Body control module Circuit breaker 19 20a Combi- nation flasher Combined rear lighting module Controller anti-lock brake Daytime running lamp module Down- stream heated oxygen sensor Engine controls system (splice s118) Engine starter motor Engine starter motor relay F11 F12 F14 F21 F23 Fuel pump relay Fuse 10a Fuse 15a Fuse 20a Fuse 30a Fuse 40a Fusible link Generator High speed radiator fan relay Ignition switch Immo- bilizer Immobilizer Instrument cluster Inter- mittent wiper relay Junction block Left door window motor relay Left power door lock switch Lock Low speed radiator fan relay Master power window switch Multi- function switch Off Pnk Power distri- bution center Power distribution center Power mirror switch Power top switch Power top up/down relays Power- train control module Radio Rear window defogger relay Red Red/ tan Right door window motor relay Right power door lock switch Right power window switch Run S102 (inside pdc) S104 (inside pdc) S105 (inside pdc) S106 (inside pdc) S113 (near breakout to map/iat sensor or in breakout to generator) S306 (w/ power locks) (in breakout for bcm) S410 Seatbelt control module Start Tan To fuse 12 (diagram 2 of 2) Trans- mission control module Trans- mission range switch Transmission relay Vapor canister leak detector Window timer module Wiper high/ low relay Power Distribution Wiring Diagram (2 of 2) for Chrysler Sebring Limited 1998 List of elements for Power Distribution Wiring Diagram (2 of 2) for Chrysler Sebring Limited 1998: 72 (near breakout to left door speaker) s400 (near breakout to map/reading lamp) (w/ visor/vanity lamps only) s302 (near breakout to right door speaker) s401 A/c comp- ressor clutch relay A/c heater control A45 Body control module C10 Cigar lighter/ power outlet Circuit breaker 18 20a Controller anti-lock brake Data link connector Daytime running lamp module Decklid release relay Fog lamp switch From a fuse 11 (diagram 1 of 2) From headlamp delay relay (diagram 2 of 2) From rear window defogger relay (diagram 2 of 2) Fuse 10a Fuse 15a Fuse 20a Fuse 40a Fuse 5 10a G206 (under right center of dash) Glove box lamp Head- lamp delay relay Headlamp switch High speed radiator fan relay Horn relay Illuminated entry relay Instrument cluster Inter- mittent wiper relay Junction block Key-in halo lamp Left door arm/ disarm switch (vtss only) Left door courtesy lamp Left headlamp Left power door lock switch Left power mirror Left visor/ vanity lamp Low speed radiator fan relay Overhead map lamp Pnk Pnk a Pnk c Pnk/ red Power amplifier Power antenna Power distribu- tion center Power distribution center Power seat switch Radio Rear floor courtesy lamp Rear window defog- ger relay Rear window defogger Red Right door arm/ disarm switch (vtss only) Right door courtesy lamp Right headlamp Right power door lock switch Right power mirror Right visor/ vanity lamp S103 (inside pdc) S134 S200 S312 (left kick panel) Seat belt control module Stop lamp switch To fuses 12 & 13 (diagram 2 of 2) To rear window defogger (diagram 2 of 2) Trav- eller Trunk lamp
POWER DOOR LOCKS Power Door Lock Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Power Door Lock Wiring Diagram for Chrysler Sebring Limited 1998: 51 Body control module Circuit breaker 20a Decklid release relay (in power distribution center) Decklid release switch Decklid solenoid Fuse 10a Fuse 15a Fused (b+) G200 (left kick panel) G206 (under right center of dash) G38 G406 (on left side of trunk lid) Gdo lockout Ground Hot at all times Hot in run Interior lights system Junction block Left power door lock motor Left power door lock switch Left remote keyless entry antenna Lf door sw Lf lock Lf unlock P158 P33 P34 P55 P58 P96 P97 Pnk Power mirror switch Power steering pressure switch Q33 Red Release ctrl Rf door sw Rf lock Rf unlock Right power door lock motor Right power door lock switch Right remote keyless entry antenna Rke ant wire S301 S306 S312 S400 S401 S402 S403
POWER MIRRORS Power Mirror Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Power Mirror Wiring Diagram for Chrysler Sebring Limited 1998: 25 Automatic day/night mirror C10 Defogger system Down Exterior lights (backup lmp switch) Fuse 4 15a Fuse 5 10a G200 (left kick panel) Hot at all times Hot in run Interior lights (illuminated entry rly) Junction block (under left side of dash) Left Left mirror Left power mirror Pnk Power mirror switch Right Right mirror Right power mirror S302 S306 S308 S402 S403
POWER SEATS Power Seat Wiring Diagrams for Chrysler Sebring Limited 1998 List of elements for Power Seat Wiring Diagrams for Chrysler Sebring Limited 1998: 14 Back Circuit breaker 18 20a Down Front vertical motor Fwd G200 (left kick panel) Horizontal motor Hot at all times Junction block (under left side of dash) Power seat switch Rear vertical motor Red S308 S312
POWER TOP/SUNROOF Power Top/Sunroof Wiring Diagrams for Chrysler Sebring Limited 1998 List of elements for Power Top/Sunroof Wiring Diagrams for Chrysler Sebring Limited 1998: 27 (body harness, near breakout for courtesy lamp relay) s311 (front center of trunk) power top pump motor (under Center (on left front inner fender) Close Down sig Fuse 15a Fuse 40a G200 (left kick panel) G400 (left front of trunk) Hot at all times Hot in run Junction block (under left side of dash) Open Power amplifier Power distribution Power top switch Power top up/down relays (front center of trunk) Red Right front seat) S320 Timer circuit Up sig W/ power door locks W/ premium radio W/o power door locks Window timer module (in left door)
POWER WINDOWS Power Window Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Power Window Wiring Diagram for Chrysler Sebring Limited 1998: 24 (1997-98) (1999-2000) (inside left door) Circuit breaker 20a G200 (left kick panel) Hot in run Junction block (under left side of dash) Left door window motor relay (inside left door) Left front Left front power window motor Left rear Left rear power window motor Master power window switch Power tops system Right door window motor relay (inside left door) Right front Right front power window motor Right power window switch Right rear Right rear power window motor S402 S410 Tan Timer circuit Window timer module
RADIO Radio Wiring Diagrams, with Amplifier for Chrysler Sebring Limited 1998 List of elements for Radio Wiring Diagrams, with Amplifier for Chrysler Sebring Limited 1998: 81 Amp l dash spkr (+) Amp l dash spkr (-) Amp l door spkr (+) Amp l door spkr (-) Amp l rear spkr (+) Amp l rear spkr (-) Amp r dash spkr (+) Amp r dash spkr (-) Amp r door spkr (+) Amp r door spkr (-) Amp r rear spkr (+) Amp r rear spkr (-) Antenna Body control module Ccd bus (+) Ccd bus (-) Convertible top down Convertible top up Dimmer signal Fuse 10a Fuse 20a Fused (b+) Fused b(+) Fused ign G200 (left kick panel) G206 (under right center of dash) G403 (right rear quarter panel) Gnd Ground Head Head/ park Headlamp sw Headlamp switch Hot at all times Hot in run or acc Junction block (under left side of dash) L front (+) L front (-) L front amp (+) L front amp (-) L rear (+) L rear (-) L rear amp (+) L rear amp (-) Left dash panel speaker Left door speaker Left rear speaker Nca Off Panel lamps Park Power amplifier (under right front seat) Power antenna Power tops system R front (+) R front (-) R front amp (+) R front amp (-) R rear (+) R rear (-) R rear amp (+) R rear amp (-) Radio Radio 12 volt output Radio 12v Red Right dash panel speaker Right door speaker Right rear speaker S134 Tan/red X12 X53 X54 X55 X56 X60 X91 X92 X93 X94 Radio Wiring Diagrams, without Amplifier for Chrysler Sebring Limited 1998 List of elements for Radio Wiring Diagrams, without Amplifier for Chrysler Sebring Limited 1998: 50 Antenna Body control module Ccd bus (+) Ccd bus (-) Dimmer signal Fuse 10a Fuse 20a Fused b(+) Fused ign G200 (left kick panel) G206 (under right center of dash) Gnd Ground Head Head/ park Headlamp sw Headlamp switch Hot at all times Hot in run or acc Junction block (under left side of dash) L front (+) L front (-) L rear (+) L rear (-) Left front door speaker Left front instrument panel speaker Left rear speaker Nca Off Panel lamps Park R front (+) R front (-) R rear (+) R rear (-) Radio Red Right front door speaker Right front instrument panel speaker Right rear speaker S134 X12 X51 X52 X53 X54 X55 X56 X57 X58
STARTING/CHARGING Charging Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Charging Wiring Diagram for Chrysler Sebring Limited 1998: 37 (eng harn, in breakout for pcm connector) s132 (eng harn, in ign- ition coil break- out s133 2.4l 2.5l Asd rly ctrl Asd rly out Auto- matic shut down relay (in pdc) Bat- tery Body control module (in jb) Ccd bus (+) Ccd bus (-) Charging system warning lamp Charging system ind ctrl Computer data lines system Engine controls system Fuse 11 10a Fuse 20a Fusible link G102 (top of left front strut tower) G129 (left rear of transmission) Gen fld dvr Generator Hot in off, run or start Ign Instrument cluster Junction block K20 Nca Power distri- bution system Power distribution center Powertrain control module (side of pdc) Red Red/tan S104 S113 S114 (engine harness, in injector breakout) S118 (engine harness, 2.4l: near engine starter motor break- out; 2.5l: near break- out for ect engine sensor) controls system Starting Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Starting Wiring Diagram for Chrysler Sebring Limited 1998: 25 (1998) (ex. 1998) A41 Acc Battery Engine starter motor Engine starter motor relay (in pdc) Fuse 20a G102 (top of left front strut tower) Hd in Ignition switch K90 Lock Off Pl in Power distribution center Powertrain control module (between air cleaner housing & pdc) Red Run S102 Start Starter relay control Tan Tan/ red Transmission control module (on left front inner fender)
SUPPLEMENTAL RESTRAINTS Supplemental Restraint Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Supplemental Restraint Wiring Diagram for Chrysler Sebring Limited 1998: 33 * ** * cirrus/stratus/breeze * z2 ** sebring convertible Airbag control module (under floor console, Airbag warning lamp Airbag warning lamp control Body control module (on junction block, under left side of dash) Ccd bus (+) Ccd bus (+) ccd bus (-) Ccd bus (-) Cirrus, stratus & breeze Cluster Data link connector (left of steering column, bottom of dash) Driver side airbag (top of steering column) F14 F23 Fuse 10a G302 (at base of gearshift) Hot in run Hot in run or start Instrument Junction block (under left side of dash) Near transmission selector) Passenger side airbag (right side of dash) R42 R43 R44 R45 S132 (eng harn, near pcm) S133 (eng harn, near ignition coil) Sebring convertible Sebring convertible only
TRANSMISSION Transmission Wiring Diagram (1 of 3) for Chrysler Sebring Limited 1998 List of elements for Transmission Wiring Diagram (1 of 3) for Chrysler Sebring Limited 1998: 74 (eng harn, near tcm breakout) (eng harn, near turbine speed sensor breakout) 2-4 press sw 2-4 pressure switch 2-4 sol ctrl 2-4 solenoid A24 A41 Auto stick dn sw Body control module Ccd bus (+) Ccd bus (-) Controller anti-lock brake D21 F11 Fuse 11 10a Fused (b+) Fused ign out G102 (top of left front strut tower) Gnd Ground Hot in off, run or start Input spd sns sig Junction block K22 K24 Low/ reverse pressure switch Low/ reverse solenoid Low/rev press Low/rev sol. ctrl Od solenoid ctrl Output shaft speed sensor (on left side of transmission case) Output spd sns Over- drive solenoid Overdrive pressure switch Pnp sw sense S100 S101 S125 S140 S141 Sci receive Sci transmit Sensor gnd Spd sensor gnd T10 T13 T14 T15 T16 T19 T20 T41 T42 T44 T47 T50 T52 T54 T59 T60 Torq mgmt req Tps sig Tr rng t42 sens Trans rly out Trans temp sig Transmission control module (on left front inner fender) Transmission solenoid & pressure switch assembly (transmission) Turbine speed sensor (on left side of torque converter housing) Ud solenoid ctrl Under- drive solenoid Vss sig Z13 Z14 Transmission Wiring Diagram (2 of 3) for Chrysler Sebring Limited 1998 List of elements for Transmission Wiring Diagram (2 of 3) for Chrysler Sebring Limited 1998: 32 (top of left front strut tower) g102 Acc Automatic shutdown relay Autostick switch (integral with gearshift mechanism) Back-up lamp switch Engine starter motor relay, fuel pump relay Exterior lights system (back-up lamps) Fuse 3 20a Fuse 5 20a Fuse 8 20a G200 (left kick panel) Hall effect switches Hot at all times Ignition switch Junction block (under left side of dash) Lock Nol Off P3l Power distribution center Prnl Red Red/ tan Red/tan Run S101 S102 S104 Start Trans temp sensor Transmission control relay Transmission range switch (in transmission, on top of valve body) Transmission Wiring Diagram (3 of 3) for Chrysler Sebring Limited 1998 List of elements for Transmission Wiring Diagram (3 of 3) for Chrysler Sebring Limited 1998: 70 (2.4l) (2.5l) (eng harn, 2.4l: near cam sensor breakout, 2.5l: near iac motor breakout) (eng harn, 2.4l: near map/iat sensor breakout, 2.5l: near egr breakout) (eng harn, 2.4l: near map/iat sensor breakout, 2.5l: near inj 6 breakout) (eng harn, in pcm breakout) (eng harn, internal to pdc) (eng harn, near ignition coil breakout) (eng harn, near pcm breakout) s120 (eng harn, near pdc breakout) (top of left front strut tower) 2.4l 2.5l A14 Battery temperature sensor Ccd bus (+) Ccd bus (-) Ckp sensor sig Column, bottom dash) Crankshaft position sensor D21 Data link connector (left of steering Double start override Ect sensor sig Engine controls system Engine coolant temperature sensor (2.4l: on top left front of eng, 2.5l: near thermostat housing) Engine starter motor relay (in power distribution center) F12 Fuel pump relay, controller anti-lock brake Fuse 10a Fuse 15a Fused b (+) G102 Gnd Hot in run Hot in run & start Ign (run/start) Instrument cluster system Junction block K22 K24 K29 K90 P/n sw sense Power distribution center Powertrain control module (between air cleaner housing & power distribution center) Red/tan S101 S105 S110 S115 S116 S117 S121 (eng harn, in pcm breakout) S127 S130 (eng harn, in pcm breakout) S132 S133 Sci transmit Sensor gnd Stop lamp switch (top of brake pedal) Stop lp sw sense T10 T41 Tan Throttle position sensor (on side of throttle body) Torque req sense Tp sens sig Vss signal Z12
TRUNK, TAILGATE, FUEL DOOR Trunk Release Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Trunk Release Wiring Diagram for Chrysler Sebring Limited 1998: 16 (on decklid latch) Body control module (on junction block) C332 Circuit breaker 18 20a Decklid release control Decklid release relay (in power dist center) Decklid release switch (center console) Decklid solenoid G406 (on left side of trunk lid) Garage door opener lockout Hot at all times Interior lights system Junction block (left side of dash) Red S301 S312
WARNING SYSTEMS Warning System Wiring Diagrams for Chrysler Sebring Limited 1998 List of elements for Warning System Wiring Diagrams for Chrysler Sebring Limited 1998: 57 (on top of engine, in ignition coil breakout) s133 Acc Body control module Ccd bus (+) Ccd bus (-) Data link connector (left side of steering column) Door ajar sw sense Door ajar switch sense Fuse 10a Fuse 15a Fuse 7 20a Fuse 8 20a Fused b (+) Fused ign (start/ run) Fused ign (start/ run/off) G10 G200 (left kick panel) G206 (under right center of dash) G26 G74 G75 Ground Head Headlamp switch Hot at all times Ignition switch Instrument cluster Junction block (under left side of dash) Key-in ignition switch sense Key-in switch Left door ajar sw sense Left door ajar swirch Left door ajar switch sense Lock Off Park Parklamp switch output Power distribution center (left front inner fender) Power steering pressure switch (mounted to power steering gear) Red Right door ajar swirch Right door ajar switch sense Run S102 S132 (left front inner fender, in breakout for pcm conn) S305 (left side of dash, in breakout for bcm) S308 Seat belt control module (rear of console) Seat belt indicator lamp Seat belt indicator lamp ctrl Seat belt switch Seat belt switch sense Start Tan Tan/ pnk Tan/pnk Tan/red
WIPER/WASHER Wiper/Washer Wiring Diagram for Chrysler Sebring Limited 1998 List of elements for Wiper/Washer Wiring Diagram for Chrysler Sebring Limited 1998: 42 (right front strut tower) Body control Fuse 10a Fuse 40a G102 (left front strut tower) G103 G103 (right front strut tower) Hi/lo control c1 High Hot at all times Hot in run and acc Instrument cluster Int Int relay ctrl Intermittent wiper relay Junction block (under left left of dash) Junction block (under left side of dash) Low Mist Module Off Park sw sense Park switch Power distribution center Power distribution center (on left front inner fender) Pump control S109 S111 Switch V10 V14 V16 V52 V55 Wash Washer fluid level sense Washer fluid level switch (sebring covertible) Windshield washer pump motor (bottom of reservoir) Windshield wiper motor Wiper Wiper high/low relay Wiper sw sig c3
