POWER DISTRIBUTION
Power Distribution Wiring Diagram (1 of 5) for Isuzu Ascender S 2008
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for Power Distribution Wiring Diagram (1 of 5) for Isuzu Ascender S 2008:
- (above left front wheelwell) underhood fuse block
- (in i/p harness, 18 cm from automatic transmission shift lever connector breakout) j320
- 4.2l
- 4wd fuse 48 15a
- 5.3l & 6.0l
- A11
- A18
- Abs fuse 33 60a
- Acc
- Air suspension compressor (w/ auto air level control)
- Atc fuse 8 30a
- Automatic transmission shift lock control actuator
- Auxiliary hvac control module (manual a/c)
- Auxiliary mode actuator
- B11
- Battery
- Body control module (bcm)
- Crank fuse 17 10a
- D9 x1
- Defrost actuator
- Elec brk fuse 19 30a
- Electronic brake control module (ebcm)
- Engine control module (ecm)
- F11
- Flat- wire
- Front driver axle actuator (w/ 2 speed push button control)
- Generator
- Hvac control module
- Hvac control module (manual a/c)
- Hvac fuse 44 30a
- Hvac i fuse 39 10a
- I/p battery fuse 48 125a
- Ign 0 fuse 47 10a
- Ign a fuse 34 40a
- Ign b fuse 36 40a
- Ignition switch
- Left air temperature actuator
- Lock
- Mode actuator
- Nca
- Pnk
- Rear fuse block (below left rear seat)
- Recirculation actuator
- Red
- Right air temperature actuator
- Run
- Start
- Starter
- Starter relay 47
- Steering wheel speed/ position sensor
- Tbc ig fuse 50 3a
- Theft deterrent module (tdc) (if equipped)
- To blower fuse 35 (diagram 2 of 5)
- To brake fuse 51 (diagram 2 of 5)
- To rear fuse block (diagram 2 of 5)
- To rear fuse block lgm/dsm fuse 19 (diagram 4 of 5)
- To underhood fuse block (diagram 3 of 5)
- Trailer connector (hd trunk trailer)
- Trailer fuse 32 30a
- Transfer case encoder motor (w/ 2 speed push button control)
- Transfer case shift control module (w/ all wheel drive & w/ 2 speed push button control)
- Transfer case shift control switch (w/ 2 speed push button control)
- Turn signal/ multi-function switch
- Underhood fuse block (above left front wheelwell)
- Vses fuse 58 fuse 61 60a
Power Distribution Wiring Diagram (2 of 5) for Isuzu Ascender S 2008
List of elements for Power Distribution Wiring Diagram (2 of 5) for Isuzu Ascender S 2008:
- (above left front wheelwell) underhood fuse block
- (in i/p harness, 33 cm from blower motor resistor assembly)
- (w/ power adjustable pedals)
- 4.2l
- 5.3l & 6.0l
- A/c fuse 30 10a
- A/c relay
- A20
- A6 x1
- Air pump fuse 56 60a
- Air suspension compressor assembly (w/ auto air level control)
- Automatic a/c
- Aux pwr 1 fuse 46 20a
- B11
- B15
- Blower fuse 35 40a
- Blower motor control module
- Blower motor resistor assembly
- Body control module (bcm)
- Brake fuse 51 10a
- C11
- Center console accessory power outlet
- Cigar lighter
- Data link connector (dlc)
- Eap fuse 15 fuse 59 15a
- Eap relay 49 (w/ power adjustable pedals)
- Ecas fuse 1 30a
- Electronic adjustable pedal (eap) relay
- Electronic brake control module (ebcm)
- Evaporative emission (evap) canister vent solenoid valve
- Flat- wire
- Fog lamp relay 39
- Fog lp fuse 11 15a
- From b ign b fuse 36 (diagram 1 of 5)
- From c hvac i fuse 39 (diagram 1 of 5)
- From ignition switch (diagram 1 of 5)
- From lgm/dsm l fuse 19 (diagram 4 of 5)
- Front accessory power outlet
- Frt wpr fuse 33 25a
- G201
- Hazrd fuse 52 25a
- Hdlp wpr relay 37 (w/ high pressure headlamp washer)
- Horn fuse 21 15a
- Horn relay 40
- Instrument panel cluster (ipc)
- Ipc/dic fuse 24 10a
- J250
- J307
- Ltr fuse 13 20a
- Manual a/c
- Nca
- Rain fuse 29 10a
- Rear fuse block (below left rear seat)
- Rear wpr relay 38
- Red
- Secondary air injection (air) pump relay (4.2l & w/ electronic air injection reactor system)
- Splice pack jx201 (at lower right front of lower console)
- Stop lamp fuse 12 25a
- Stoplamp switch
- Tbc acc fuse 31 3a
- Tbc run fuse 52 3a
- Tcm cnstr fuse 26 fuse 15 10a
- Tcm fuse 35 10a
- To ecm fuse 29 (diagram 3 of 5)
- Transmission control module (tcm)
- Turn signal/ hazard flasher module
- Underhood fuse block (above left front wheelwell)
- Windshield outside moisture sensor (if equipped)
- Windshield wiper motor
- Wpr fuse 7 20a
- Wsw fuse 9 15a
- Wsw relay 42
Power Distribution Wiring Diagram (3 of 5) for Isuzu Ascender S 2008
List of elements for Power Distribution Wiring Diagram (3 of 5) for Isuzu Ascender S 2008:
- (4.2l)
- (in automatic transmission)
- (in fuel injector harness) j111
- (not used)
- (w/ power adjustable pedals) eap relay
- 1-2 shift solenoid (ss) valve
- 2-3 shift solenoid (ss) valve
- 3-2 shift solenoid (ss) valve
- 4.2l
- 5.3l & 6.0l
- Air bag fuse 18 10a
- Air sol fuse 54 15a
- Air sol relay 55
- Automatic transmission
- Back-up fuse 27 15a
- Before breakout to inflatable restraint sensing & diagnostic module) j220
- Body control module (bcm)
- E12
- Ecm fuse 29 (5.3l & 6.0l) 10a
- Ecmi fuse 28 15a
- Engine control module (ecm)
- From air sol fuse 54 f (diagram 3 of 5)
- From hazrd fuse 52 d (diagram 2 of 5)
- From ignition switch (diagram 1 of 5)
- Fuel injector 1
- Fuel injector 2
- Fuel injector 3
- Fuel injector 4
- Fuel injector 5
- Fuel injector 6
- Fuel pump relay 41
- Generator battery control module
- Hdm fuse 53 fuse 57 15a
- Hdm relay 46
- Hi headlamp relay 43
- Ign coils fuse 14 10a
- Ignition coil 1
- Ignition coil 2
- Ignition coil 3
- Ignition coil 4
- Ignition coil 5
- Ignition coil 6
- Inflatable restraint passenger presence system (pps) module
- Inflatable restraint sensing & diagnostic module (sdm)
- Inflatable restraint vehicle rollover sensor
- Input speed sensor (iss)
- J133
- J134
- Park/ neutral position (pnp) switch
- Pcm b fuse 10 20a
- Pcm i fuse 28 15a
- Pnk
- Powertrain control module (pcm)
- Powertrain relay 57 relay 60
- Red
- Rvc fuse 48 fuse 62 10a
- Secondary air injection (air) pump relay (4.2l & electronic air injection reactor system)
- Security immobilization equipment system
- Tbc 1 fuse 31 fuse 58 10a
- Theft deterrent alarm
- Theft deterrent alarm (if equipped)
- Theft deterrent module (tdm)
- To air bag fuse 18 (diagram 3 of 5)
- To ign e fuse 22 (diagram 4 of 5)
- Torque converter clutch (tcc) pulse width modulation (pwm) solenoid valve
- Torque converter clutch (tcc) solenoid valve
- Trans fuse 53 15a
- Transmission control module (tcm)
- Underhood fuse block (above left front wheelwell)
- X175 e
Power Distribution Wiring Diagram (4 of 5) for Isuzu Ascender S 2008
List of elements for Power Distribution Wiring Diagram (4 of 5) for Isuzu Ascender S 2008:
- (in body harness channel on rear floor, 12 cm to left of jx306) (security immobilization equipment system) j374
- (in i/p harness, above dash left lower panel, 11 cm from steering column breakout) j239
- A/c relay 44
- A19
- Amp fuse 11 20a
- Audio amplifier
- Automatic a/c
- Auxiliary hvac control module
- Body control module (bcm)
- C10
- D10
- D12
- Ddm fuse 10 10a
- Digital radio receiver
- Digital video disc (dvd) player
- Driver door module (ddm)
- Driver memory seat module
- E12
- E2 x3
- Flat-wire
- From radio fuse 41 h (diagram 4 of 5)
- From trans fuse 53 g (diagram 3 of 5)
- From underhood fuse block, i/p battery fuse 48 (diagram 1 of 5)
- Front passenger door module (fpdm)
- Garage door opener (gdo)
- Headlamp switch (if equipped)
- Hvac b fuse 36 10a
- Hvac control module
- Ign e fuse 22 10a
- Inside rearview mirror (if equipped)
- Instrument panel cluster (ipc)
- J341 (in headliner harness, 6.5 cm from breakout to left clearance lamp)
- Left headlamp leveling actuator (if equipped)
- Left rear window switch
- Lgm/dsm fuse 19 10a
- Liftgate module (lgm)
- Lt doors circuit breaker 2 25a
- Oh batt/onstar fuse 27 10a
- Park/ neutral position (pnp) switch
- Pdm fuse 12 10a
- Pnk
- Premium
- Radio
- Radio fuse 41 15a
- Rear fuse block (below left rear seat)
- Red
- Right headlamp leveling actuator (if equipped)
- Right rear window switch
- Rt doors circuit breaker 1 25a
- Stop lamp switch
- Tbc ign 1 fuse 16 10a
- To aux pwr 1 fuse 46 (diagram 2 of 5)
- To hvac b fuse 36 (diagram 4 of 5)
- To lgm 2 fuse 3 (diagram 5 of 5)
- Turn signal/ multi- function switch
- Underhood fuse block (above left front wheelwell)
- Vehicle communication interface module (w/ vehicle communication system)
- Vehicle inclination sensor
- W/ digital audio system
- W/ memory
- W/ rear seat enter- tainment package & garage door opener
- W/ rear seat enter- tainment package, w/o garage door opener
- W/o rear seat enter- tainment package, w/ garage door opener
- X2 a5
- X2 d5
Power Distribution Wiring Diagram (5 of 5) for Isuzu Ascender S 2008
List of elements for Power Distribution Wiring Diagram (5 of 5) for Isuzu Ascender S 2008:
- (diagram 4 of 5)
- (diagram 5 of 5)
- (not used)
- B13
- B17
- Body control module (bcm)
- Driver memory seat module
- Driver seat adjuster switch
- Driver seat lumbar adjuster switch
- Flat- wire
- From amp fuse 11 j
- From tbc 5 fuse 32 k
- J318 (in driver's seat harness, 7 cm from breakout to body connector)
- J319 (in passenger seat harness, 7cm from breakout to body connector)
- J328
- J329
- Lgm 2 fuse 3 30a
- Liftgate module (lgm)
- Lock relay 18
- Locks fuse 21 10a
- Park lp relay 30
- Passenger seat adjuster switch
- Passenger seat lumbar adjuster switch
- Rear fuse block (below left rear seat)
- Rear window wiper motor
- Rr hvac fuse 13 30a
- Rr wiper circuit breaker 9 15a
- Seats circuit breaker 8 30a
- Sunroof fuse 28 20a
- Sunroof motor (if equipped)
- Tbc 2 fuse 7 10a
- Tbc 3 fuse 4 10a
- Tbc 4 fuse 40 10a
- Tbc 5 fuse 32 10a
- To seats circuit breaker 8 (diagram 5 of 5)
- Unlock relay 24
- W/ deluxe seats
- W/ memory
- W/o memory