POWER DISTRIBUTION
Power Distribution Wiring Diagram, Early Production (1 of 6) for Isuzu Rodeo S 1995
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO List of elements for Power Distribution Wiring Diagram, Early Production (1 of 6) for Isuzu Rodeo S 1995:
- 2.6l
- Battery
- Brake light switch
- C105
- C106
- Charge relay
- Coil
- Combination switch
- Contact
- Dash fuse box
- Engine control module (ecm) relay
- Fuel pump relay
- Fuse 1 10a
- Fuse 1 15a
- Fuse 2 10a
- Fuse 2 20a
- Fuse 3 15a
- Fuse 4 10a
- Fuse 4 25a
- Fuse/ relay box
- Fuse/relay box
- Generator
- Headlight relay
- Heater a/c relay
- Light switch
- Low note horn
- Main fuse 1 60a
- Main fuse 2 30a
- Rear defogger relay
- Rear wheel anti-lock brake controller
- Red
- Starter
- Starter solenoid
- To fuse 3 (diagram 4 of 6)
- To ignition switch (diagram 2 of 6)
Power Distribution Wiring Diagram, Early Production (2 of 6) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Early Production (2 of 6) for Isuzu Rodeo S 1995:
- (not used)
- 2.6l
- Acc
- Air regulator
- C211
- C283
- C284
- Cigarette lighter
- Clutch start switch
- Contact
- Dash fuse box
- Engine control module (ecm)
- From main fuse 1 (hot at all times) (diagram 1 of 6)
- Fuel pump
- Fuel pump relay
- Fuse 12 10a
- Fuse 12 15a
- Fuse 13 20a
- Fuse 5 20a
- Fuse 6 10a
- Fuse 9 15a
- Fuse/ relay box
- Fuse/relay box
- G200 (below left side of i/p, behind engine control module (ecm))
- Heated oxygen sensor (ho2s)
- Ignition coil
- Ignition switch
- Lock
- Nca
- Off
- On acc
- Power mirror switch
- Radio
- Radio noise suppressor
- Rear wheel anti-lock brake controller
- Red
- Start
- To fuse 10 (diagram 5 of 6)
- To fuse 8 (diagram 6 of 6)
- To fuses 6 & 7 (diagram 5 of 6)
Power Distribution Wiring Diagram, Early Production (3 of 6) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Early Production (3 of 6) for Isuzu Rodeo S 1995:
- (not used)
- (not used) (manual)
- 3.2l
- Automatic door lock control relay
- Battery
- Brake light switch
- C150
- C16
- C218
- C219
- Charge relay
- Circuit breaker 30a
- Coil
- Combination switch
- Condenser fan fuse 30a
- Condenser fan relay
- Contact
- Dash fuse box
- Ecm fuse 30a
- Engine control module (ecm)
- Engine control module (ecm) relay
- Fuel pump relay
- Fuse 1 10a
- Fuse 2 10a
- Fuse 2 15a
- Fuse 3 15a
- Fuse 4 10a
- Fuse 4 25a
- Fuse/ relay box
- Fuse/relay box
- Generator
- Headlight relay
- Heater a/c relay
- High note horn (ls models)
- Light switch
- Low note horn
- Main fuse 1 60a
- Main fuse 2 30a
- Power window relay
- Rear defogger relay
- Rear wheel anti-lock brake controller
- Red
- Safety lock control unit (automatic)
- Starter
- Starter relay
- Starter solenoid
- Tailgate opener switch
- To fuse 3 (diagram 4 of 6)
- To ignition switch (diagram 4 of 6)
- Transmission control module (tcm) (automatic)
Power Distribution Wiring Diagram, Early Production (4 of 6) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Early Production (4 of 6) for Isuzu Rodeo S 1995:
- A/t
- Acc
- Automatic transmission mode switch
- C176
- C211
- C283
- C284
- C286
- C900
- C902
- C904
- Cigarette lighter
- Clutch start switch
- Coil
- Dash fuse box
- Dome light
- Electronic ignition (ei) system
- Engine control module (ecm) (2.6l)
- From main fuse 1 (hot at all times) (diagram 3 of 6) (3.2l only)
- From main fuse 1 (hot at all times) 2.6l - (diagram 1 of 6) 3.2l - (diagram 3 of 6)
- Fuse 11 10a
- Fuse 12 15a
- Fuse 13 20a
- Fuse 3 10a
- Fuse 5 10a
- Fuse 9 15a
- Fuse/relay box
- G200 (below left side of i/p, behind engine control module (ecm))
- Ignition switch
- Key remind switch
- Left front door courtesy light (ls models)
- Left rear door courtesy light (ls models)
- Lock
- Luggage room light
- M/t
- Off
- On acc
- Power mirror switch
- Radio
- Rear wheel anti-lock brake controller
- Red
- Right front door courtesy light (ls models)
- Right rear door courtesy light (ls models)
- Spot light assembly (ls models)
- Start
- Starter relay
- To fuse 10 (diagram 5 of 6)
- To fuse 8 (diagram 6 of 6)
- To fuses 6 & 7 (diagram 5 of 6)
Power Distribution Wiring Diagram, Early Production (5 of 6) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Early Production (5 of 6) for Isuzu Rodeo S 1995:
- (2.6l)
- (3.2l)
- (not used)
- Automatic transmission warning/ indicator assembly (3.2l)
- C274
- C275
- C276
- Coil
- Combination switch
- Contact
- Dash fuse box
- From ignition switch (hot in on or start) 2.6l - (diagram 2 of 6) 3.2l - (diagram 4 of 6)
- Fuse 10 10a
- Fuse 6 15a
- Fuse 7 10a
- Fuse/relay box
- Instrument cluster
- Intermittent windshield wiper/washer
- Mirror defogger switch
- Power window relay (if equipped)
- Rear defogger switch
- Rear wiper relay (if equipped)
- Red
- Safety lock control unit (automatic)
- Vehicle speed sensor (3.2l)
- Warning buzzer control unit
- Windshield wiper motor
- Windshield wiper relay
- Windshield wiper relay connector plug
- Windshield wiper/washer
- Windshield wiper/washer switch
Power Distribution Wiring Diagram, Early Production (6 of 6) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Early Production (6 of 6) for Isuzu Rodeo S 1995:
- (2.6l)
- (3.2l)
- 2.6l
- 3.2l
- Back up lights switch
- Brake light switch (3.2l)
- C106
- C150
- C312
- C313
- C332
- C333
- Cruise control switch (3.2l)
- Dash fuse box
- Diode box b
- Engine control module (ecm) relay (2.6l)
- Engine control module (ecm) relay (3.2l)
- Evaporative emission canister purge vacuum switching valve (3.2l)
- Exhaust gas recirculation (egr) vacuum switching valve (3.2l)
- From ignition switch (hot in on or start) 2.6l - (diagram 2 of 6) 3.2l - (diagram 4 of 6)
- Fuse 8 10a
- Fuse/ relay box
- Fuse/relay box
- Generator
- Heated oxygen sensor (ho2s) (3.2l)
- Nca
- Neutral switch (with cruise control)
- Red
- Transmission switch 1-2
- Transmission switch 3-4
Power Distribution Wiring Diagram, Late Production (1 of 3) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Late Production (1 of 3) for Isuzu Rodeo S 1995:
- (2.6l)
- (3.2l)
- 2.6l
- 3.2l
- 3.2l a/t
- 3.2l only
- A-27
- A-28
- A/c dual pressure switch
- A/c switch
- A/c triple pressure switch
- Acc
- All others
- Battery
- Blower motor
- C16
- Charge relay
- Condenser fan relay switch
- E-25
- E-46
- Eb-1 hazard fuse 15a
- Eb-11 fuel pump fuse 20a
- Eb-12 ecm fuse 15a
- Eb-15 ign fuse 60a
- Eb-16 main fuse 100a
- Eb-17 cond fan fuse (3.2l only) 30a
- Eb-2 horn fuse 10a
- Eb-4 blower fuse 20a
- Eb-5 air cond fuse 10a
- Ecm main relay
- Engine control module
- From sb1 (hot at all times) (diagram 2 of 3)
- Fuel pump relay
- Fuse/ relay box
- Generator
- Hazard warning switch
- Headlight relay
- Heater- a/c relay
- Horn relay
- Ignition switch
- Lock
- Off
- Red
- Start
- Starter
- Starter relay
- To cb-1 (diagram 2 of 3)
- To cb-11 (diagram 3 of 3)
- To cb-19 (diagram 2 of 3)
- To cb-3 (diagram 3 of 3)
- To sb1 (hot at all times) (diagram 2 of 3)
Power Distribution Wiring Diagram, Late Production (2 of 3) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Late Production (2 of 3) for Isuzu Rodeo S 1995:
- (not used)
- 3.2l m/t
- A-27
- A-63
- A/t
- A/t only
- Brake switch
- Cb-1 starter fuse 10a
- Cb-13 stop fuse 15a
- Cb-14 door lock fuse (3.2l only) 20a
- Cb-17 rr def no 1 fuse 15a
- Cb-18 rr def no 2 fuse 15a
- Cb-19 audio fuse 15a
- Cb-20 cigar fuse 20a
- Cb-23 rwal fuse 20a
- Cb-27 power window cb (3.2l only) 30a
- Cb-5 tail illum fuse 15a
- Cb-9 room fuse 10a
- Cigarette lioghter
- Clutch interlock switch
- Dash fuse box
- Dome light
- Electronic brake control module
- Engine conrol module (2.6l only)
- From fuse/ a relay box (hot at all times) (diagram 1 of 3)
- From ignition switch b (hot in acc or on) (diagram 1 of 3)
- From ignition switch d (hot in start) (diagram 1 of 3)
- Fuse/relay box
- G200 (below left side of i/p, above kick panel)
- Hatch release switch (3.2l only)
- Ignition switch
- Key reminder switch
- Left front door courtesy light
- Left front door power window & lock switch
- Left rear door courtesy light
- Ls only
- Luggage room light
- M/t
- Mirror control switch
- Only
- Power window relay
- R-6
- Radio
- Rear defogger relay
- Red
- Right front door courtesy light
- Right rear door courtesy light
- Sb1
- Shift lock controller (a/t)
- Spotlight (ls only)
- Starter relay
- Taillight relay
- To ignition switch (hot at all times) (diagram 1 of 3)
- Transmission control module
Power Distribution Wiring Diagram, Late Production (3 of 3) for Isuzu Rodeo S 1995
List of elements for Power Distribution Wiring Diagram, Late Production (3 of 3) for Isuzu Rodeo S 1995:
- (2.6l) (3.2l)
- 2.6l
- 3.2l
- 3.2l only
- A/t
- A/t only
- A/t shift indicator controller
- Automatic transmission mode switch
- Back up lights switch
- Cb-11 front wiper fuse 20a
- Cb-12 elec ign fuse (3.2l only) 10a
- Cb-15 back up turn fuse 15a
- Cb-16 rear wiper fuse 10a
- Cb-21 srs (1) fuse 10a
- Cb-22 srs (2) fuse 10a
- Cb-3 engine device fuse 15a
- Cb-4 ign coil fuse 15a
- Cb-7 meter fuse 15a
- Clutch interrupt switch (m/t)
- Combination switch
- Cruise control main unit
- Cruise control unit
- Dash fuse box
- Diode box b (2.6l only)
- Ecm main relay
- Electronic ignition assembly
- Evaporative emission canister purge vacuum valve
- Exhaust gas recirculation vacuum valve
- From ignition switch (hot in on c or start) (diagram 1 of 3)
- From ignition switch (hot in on e or start) (diagram 1 of 3)
- Fuse/ relay box
- Generator
- Hazard warning switch
- Ignition coil
- Intermittent windshield wiper relay or connector plug
- M/t
- Meter assembly
- Mirror defogger switch
- Power window relay
- Radio noise suppressor
- Rear defogger relay
- Rear wiper relay
- Red
- Seat belt, key & light reminder buzzer
- Sensing and diagnostic module
- Shift lock controller (a/t)
- U-3
- Vehicle speed sensor
- Windshield wiper motor
- Windshield wiper/ washer switch