ENGINE PERFORMANCE
2.4L
2.4L, Engine Performance Wiring Diagram (1 of 4) for Chrysler Sebring Touring 2008
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for 2.4L, Engine Performance Wiring Diagram (1 of 4) for Chrysler Sebring Touring 2008:
- (at left rear quarter panel) g303
- (downstream: in exhaust, after catalytic converter) oxygen sensor 1/2
- (in front of left shock tower) s127
- (left rear of engine compt) secondary air pump
- (on left shock tower)
- (on left shock tower) g111
- (pzev)
- A804
- A931
- Accelerator pedal position sensor (top of accelerator pedal)
- App sens ground 1
- App sens ground 2
- App signal 1
- App signal 2
- Asd/main rly ctrl
- B(+)
- B15
- B16
- Brake signal 1
- Brake signal 2
- C10
- C11
- Can c bus (+)
- Can c bus (-)
- Computer data lines system
- D64
- D65
- Early production: z902 late production: z931
- Electronics
- Esm sig
- Esm signal
- Evap monitor system switch (under left rear of vehicle)
- Evap purge ctrl
- Evap purge rtn
- Evap/purge solenoid (left rear of engine compt)
- F202
- F342
- F962
- Fuel pump ctrl
- Fuse 10a
- Fuse 40a
- Fused asd/main rly out
- Fused b(+)
- G111
- G111 (on left shock tower)
- Gen sense
- Ground
- Hot at all times
- Ign sw out (run-start)
- Ign sw out (start)
- K107
- K141
- K167
- K23
- K29
- K299
- K31
- K400
- K51
- K52
- K70
- K852
- K854
- K904
- O2 1/2 heater ctrl
- O2 1/2 rtn
- O2 1/2 signal
- Powertrain control module (left rear of engine compt)
- Red
- S/c sig 1
- S/c sig 2
- S/c signal 1
- S/c signal 2
- S/c sw gnd
- S/c sw ground
- S103 (in front of left shock tower)
- S110
- S112
- S153
- Secondary air pump relay (left rear of engine compt)
- Starter ctrl
- Starting/ charging system
- Steering control module (on steering column)
- T16
- T41
- T752
- Totally integrated power module (left side of engine compt)
- Trans ctrl out
- Transmission ctrl out
- Trs t41 signal
- V71
- V72
- V937
2.4L, Engine Performance Wiring Diagram (2 of 4) for Chrysler Sebring Touring 2008
List of elements for 2.4L, Engine Performance Wiring Diagram (2 of 4) for Chrysler Sebring Touring 2008:
- (at left
- (behind left headlight) s120
- (inside left front fender) s126
- (pzev)
- (top of brake pedal) stop lamp switch
- 2-4 pres sig
- 5v sply
- A/c comp ctrl
- Air condi- tioning system
- Asd/ main relay
- B(+)
- C10
- C11
- C27
- Cmp 1/2 sig
- Ect 2 sig
- Electronics
- Eot sig
- Etc motor (+)
- Etc motor (-)
- F202
- F855
- F856
- Fuse 10a
- Fuse 15a
- Fuse 30a
- Fuse 40a
- G24
- G302
- Hot at all times
- Iat sig
- Ign sw out (run- start)
- Injector 1 ctrl
- Injector 2 ctrl
- Injector 3 ctrl
- Injector 4 ctrl
- K11
- K12
- K124
- K126
- K13
- K14
- K21
- K222
- K41
- K441
- K601
- K902
- Kick panel)
- L/r pres sig
- L53
- Line pressure sensor/variable force solenoid assembly (left side of transaxle)
- Lp vfs ctrl
- Lp vfs sig
- Mfv ctrl
- O2 1/1 return
- O2 1/1 sig
- Od pres sig
- Powertrain control module (left rear of engine compt)
- Red
- Relay block (left side of engine compt)
- S117
- S172 (in breakout to c106, above transmission)
- S187
- Sens gnd
- Stop lamp sw out
- T118
- T15
- T38
- T47
- T50
- T854
- Tans ctrl out
- Totally integrated power module (left side of engine compt)
- Trans ctrl
2.4L, Engine Performance Wiring Diagram (3 of 4) for Chrysler Sebring Touring 2008
List of elements for 2.4L, Engine Performance Wiring Diagram (3 of 4) for Chrysler Sebring Touring 2008:
- (at top left of engine) fuel injectors
- (except pzev)
- (in breakout to c101 & pcm c2)
- (left front of engine) camshaft position solenoid 1/1
- (left front of engine) engine coolant temperature sensor 2
- (left front of engine) oil temperature sensor
- (near breakout to ignition coil 5) s190
- (on left shock tower) g111
- (right front of engine) camshaft position solenoid 1/2
- (right rear of engine) oxygen sensor 1/1
- 5v sply
- B(+)
- Camshaft position sensor 1/1 (left rear of engine)
- Camshaft position sensor 1/2 (right rear of engine)
- Ckp sig
- Cmp 1/1 sig
- Cmp 1/2 sig
- Crankshaft position sensor (right rear of engine)
- Electronics
- Engine coolant temperature sensor 1 (rear of engine)
- Etc mtr (+)
- Etc mtr (-)
- F901
- Fuel level sig 1
- Fuel pump ctrl out
- Fuel pump module (in fuel tank)
- G111 (on left shock tower)
- G303 (at left rear quarter panel)
- Gnd
- Ground
- Hot at all times
- Ign sw out (unlock- run-start)
- Instrument cluster system
- Intake air temperature sensor (on intake manifold)
- Manifold flow valve (left rear of engine)
- Map sensor (left front of engine)
- Map sig
- Mfv ctrl
- Mfv sig
- Pnk/red
- S181
- S184 (in breakout to c101 & pcm c2)
- S184 (in breakout to s184 c101 & pcm c2)
- S191 (near throttle body)
- S192 (below throttle body)
- S199
- Sens gnd
- Throttle body (left rear of engine)
- Totally integrated power module (left side of engine compt)
- Tp sens gnd
- Tp sig 1
- Tp sig 2
- Z916
2.4L, Engine Performance Wiring Diagram (4 of 4) for Chrysler Sebring Touring 2008
List of elements for 2.4L, Engine Performance Wiring Diagram (4 of 4) for Chrysler Sebring Touring 2008:
- (top of engine, near ignition coil breakout 4) s196
- (top right side of engine) ignition coils
- 2-4 ctrl
- 2-4 pressure switch
- 2-4 solenoid
- Air flow sensor (left rear of engine compt) (pzev)
- Ckp sig
- Cmp 1/1 ctrl
- Cmp 1/1 sig
- Cmp 1/2 ctrl
- Coil 1 ctrl
- Coil 2 ctrl
- Coil 3 ctrl
- Coil 4 ctrl
- Ect 1 sig
- Engine oil pressure switch (lower left side of engine)
- Eop sig
- F901
- Gen field ctrl
- Ign sw out (unlock-run-start)
- Ignition capacitor 1 (rear of engine)
- In speed sig
- Input speed sensor (on left side of transaxle)
- K122
- K15
- K157
- K17
- K18
- K19
- K20
- K22
- K24
- K276
- K42
- K44
- K602
- K76
- K900
- K915
- K922
- K942
- K957
- K99
- Knock sensor (left side of engine)
- Ks return
- Ks sig
- L/r ctrl
- L/r pressure switch
- L/r solenoid
- Map sig
- Mfv sig
- Nca
- Nol
- O2 1/1 heater ctrl
- Od ctrl
- Od pressure switch
- Od solenoid
- Out speed sig
- Output speed sensor (on left side of transaxle case)
- P3l
- Pnk/red
- Powertrain control module (left rear of engine compt)
- Prnl
- S101 (in breakout to pcm c2) (except pzev)
- S171 (in breakout to pcm c4)
- S194
- Saf signal
- Sens ground
- Starting/charging system
- T13
- T14
- T19
- T20
- T41
- T42
- T52
- T54
- T59
- T60
- T853
- Tp sens ground
- Tp sig 1
- Tp sig 2
- Trans temp sig
- Transmission range sensor (on lower left side of transaxle)
- Transmission solenoid/ pressure switch assembly (on left side of transaxle)
- Transmission temperature sensor
- Trs t1 sig
- Trs t3 sig
- Trs t41 sig
- Trs t42 sig
- Ud ctrl
- Ud solenoid
2.7L FLEX FUEL
2.7L Flex Fuel, Engine Performance Wiring Diagram (1 of 5) for Chrysler Sebring Touring 2008
List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram (1 of 5) for Chrysler Sebring Touring 2008:
- (in front of left shock tower)
- (on left shock tower) g111
- (right side of engine block) engine oil pressure switch
- (run-start)
- (unlock-run-start)
- A/c comp ctrl
- A804
- A931
- Accelerator pedal position sensor (top of accelerator pedal)
- Air conditioning system
- App sens gnd 1
- App sens gnd 2
- App sig 1
- Asd/ main relay
- Asd/main rly ctrl
- Asd/main rly out
- Autostick down sig
- Autostick up sig
- B(+)
- B15
- B16
- Brake sig 1
- Brake sig 2
- C10
- C11
- C27
- Can c bus (+)
- Can c bus (-)
- Computer data lines system
- D64
- D65
- Early production: z902 late production: z931
- Electronics
- Eop sig
- Evap purge ctrl
- Evap purge rtn
- Evap/purge solenoid
- F202
- F342
- F856
- F901
- F962
- Fuse 10a
- Fuse 15a
- Fuse 30a
- Fuse 40a
- Fused asd/ main rly out c1
- Fused b(+)
- Gen sense
- Ground
- Hot at all times
- Ign sw out
- Ign sw out (start)
- Ign sw out (unlock- run-start)
- K141
- K167
- K23
- K243
- K299
- K399
- K400
- K51
- K52
- K70
- K904
- O2 1/2 heater ctrl
- O2 1/2 sig
- O2 2/2 heater ctrl
- O2 2/2 sig
- O2 rtn (down)
- Oxygen sensor 1/2 (right side of engine)
- Oxygen sensor 2/2 (left side of engine)
- Pnk/red
- Powertrain control module (left rear of engine compt)
- Red
- Relay block (left side of engine compt)
- S/c sig 2
- S/c sw gnd
- S103
- S106 (in breakout to manifold tuning valve solenoid)
- S110
- S114 (below left shock tower ground)
- S123
- Shift interlock system
- Sig 1
- Sig 2
- Starting/ charging system
- Steering control module (on steering column)
- Sw gnd
- T44
- Totally integrated power module (left side of engine compt)
- V71
- V72
- V937
2.7L Flex Fuel, Engine Performance Wiring Diagram (2 of 5) for Chrysler Sebring Touring 2008
List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram (2 of 5) for Chrysler Sebring Touring 2008:
- (at left
- (at left rear quarter panel) g303
- (behind left headlight) s120
- (inside left front fender) s126
- (on left shock tower) g111
- (right side of front bumper beam) ambient air temperature sensor
- (top of brake pedal) stop lamp switch
- Aat rtn
- Aat sig
- App sig 2
- B(+)
- B20
- Brake fluid level sensor
- Brake fluid level sig
- C10
- C11
- Electronics
- Esm sig
- Evap monitor system switch (under left rear of vehicle)
- F202
- Fuel level sig 1
- Fuel pump ctrl
- Fuel pump ctrl out
- Fuel pump module
- Fuse 10a
- G302
- G303 (at left rear quarter panel)
- G31
- G931
- Ground
- Hot at all times
- Ign sw out (run- start)
- Instrument cluster system
- K107
- K29
- K31
- Kick panel)
- L53
- Nol
- P3l
- Powertrain control module (left rear of engine compt)
- Prnl
- Red
- S/c sig 1
- Starter ctrl
- Stop lamp sw out
- T15
- T16
- T752
- Totally integrated power module (left side of engine compt)
- Trans ctrl
- Trans ctrl out
- Transmission range sensor (on lower left side of transaxle)
- Transmission temperature sensor
- V71
- Z916
2.7L Flex Fuel, Engine Performance Wiring Diagram (3 of 5) for Chrysler Sebring Touring 2008
List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram (3 of 5) for Chrysler Sebring Touring 2008:
- (in breakout to c106, above transmission) s172
- (on left shock tower) g111
- 2-4 ctrl
- 2-4 pressure sig
- 2-4 pressure switch
- 2-4 solenoid
- 5v sply
- Early production: z902
- Ground
- Input speed sig
- L/r ctrl
- L/r pressure sig
- L/r pressure switch
- L/r solenoid
- Late production: z931
- Line pressure sensor/variable force solenoid assembly (left side of transaxle)
- Lp vfs ctrl
- Lp vfs sig
- Od ctrl
- Od pressure sig
- Od pressure switch
- Od solenoid
- Out speed sig
- Powertrain control module (left rear of engine compt)
- S171 (in breakout to pcm c4)
- Sens gnd
- Sens ground
- T118
- T13
- T14
- T15
- T16
- T19
- T20
- T38
- T41
- T42
- T47
- T50
- T52
- T54
- T59
- T60
- Trans ctrl
- Trans ctrl out
- Trans temp sig
- Transmission solenoid/ pressure switch assembly (on left side of transaxle)
- Trs t1 sig
- Trs t3 sig
- Trs t41 sig
- Trs t42 sig
- Ud ctrl
- Ud solenoid
2.7L Flex Fuel, Engine Performance Wiring Diagram (4 of 5) for Chrysler Sebring Touring 2008
List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram (4 of 5) for Chrysler Sebring Touring 2008:
- (on left side of transaxle case) output speed sensor
- (on left side of transaxle) input speed sensor
- 5v sply
- Camshaft position sensor (front of left cylinder bank)
- Egr valve assembly (top rear of engine)
- Engine coolant temperature sensor 1
- G111 (on left shock tower)
- Gnd
- Intake air temperature sensor
- Map sensor (top right rear of engine)
- S181 (in breakout to c101 & pcm c2)
- S182 (in injector harness, below throttle body)
- S191 (near throttle body)
- S199 (near injector no. 6)
- Sens gnd
2.7L Flex Fuel, Engine Performance Wiring Diagram (5 of 5) for Chrysler Sebring Touring 2008
List of elements for 2.7L Flex Fuel, Engine Performance Wiring Diagram (5 of 5) for Chrysler Sebring Touring 2008:
- (on left shock tower) g111
- (top of left cylinder bank) fuel injectors
- (top of left valve cover) ignition coils
- (top of right cylinder bank) fuel injectors
- (top of right valve cover) ignition coils
- 5v sply
- Ckp sig
- Cmp sig
- Coil 1 ctrl
- Coil 2 ctrl
- Coil 3 ctrl
- Coil 4 ctrl
- Coil 5 ctrl
- Coil 6 ctrl
- Crankshaft position sensor (right rear of engine)
- Ect 1 sig
- Egr ctrl
- Egr sig
- Etc motor (+)
- Etc motor (-)
- Etc mtr (+)
- Etc mtr (-)
- F855
- Gen field ctrl
- Iat sig
- Ignition capacitor 1 (rear of right cylinder bank)
- Ignition capacitor 2 (rear of left cylinder bank)
- Inj 1 ctrl
- Inj 2 ctrl
- Inj 3 ctrl
- Inj 4 ctrl
- Inj 5 ctrl
- Inj 6 ctrl
- K10
- K11
- K12
- K122
- K124
- K126
- K13
- K14
- K15
- K16
- K17
- K18
- K19
- K199
- K20
- K21
- K22
- K24
- K34
- K35
- K38
- K41
- K42
- K43
- K44
- K58
- K900
- K902
- K922
- K942
- K99
- Knock sensor (below throttle body)
- Ks rtn
- Ks sig
- Map sig
- Nca
- O2 1/1 heater ctrl
- O2 1/1 sig
- O2 2/1 heater ctrl
- O2 2/1 sig
- O2 rtn (up)
- Oxygen sensor 1/1 (right front of engine)
- Oxygen sensor 2/1 (left rear of engine)
- Powertrain control module (left rear of engine compt)
- S184 (in breakout to c101 & pcm c2)
- S190 (near breakout to ignition coil 5)
- S192 (below throttle body)
- S195 (between ignition coil breakouts to 4 & 6)
- Sens ground
- Starting/ charging system
- Throttle body (top rear of engine)
- Tp sens gnd
- Tp sens ground
- Tp sig 1
- Tp sig 2
3.5L
3.5L, Engine Performance Wiring Diagram (1 of 5) for Chrysler Sebring Touring 2008
List of elements for 3.5L, Engine Performance Wiring Diagram (1 of 5) for Chrysler Sebring Touring 2008:
- (in front of left shock tower)
- (left front side of engine block) engine oil pressure switch
- (on left shock tower) g111
- (run-start)
- (unlock- run-start)
- 5v sply
- A/c comp ctrl
- A804
- A931
- Accelerator pedal position sensor (top of accelerator pedal)
- Air conditioning system
- App sens gnd 1
- App sens gnd 2
- App sig 1
- Asd/ main relay
- Asd/main rly ctrl
- Asd/main rly out
- Autostick down sig
- Autostick up sig
- B(+)
- B15
- B16
- Brake sig 1
- Brake sig 2
- C10
- C11
- C27
- Can c bus (+)
- Can c bus (-)
- Computer data lines system
- D64
- D65
- Early production: z902 late production: z931
- Electronics
- Eop sig
- Evap purge ctrl
- Evap purge rtn
- Evap/purge solenoid (left rear of engine compt)
- F202
- F342
- F856
- F901
- F962
- Fuse 10a
- Fuse 15a
- Fuse 30a
- Fuse 40a
- Fused asd/ main rly out c1
- Fused b(+)
- Gen sense
- Ground
- Hot at all times
- Ign sw out
- Ign sw out (start)
- Ign sw out (unlock- run-start)
- K141
- K167
- K23
- K234
- K235
- K236
- K243
- K299
- K399
- K400
- K51
- K52
- K70
- K904
- Mtv sig
- O2 1/2 heater ctrl
- O2 1/2 sig
- O2 2/2 heater ctrl
- O2 2/2 sig
- O2 rtn (down)
- Oxygen sensor 1/2 (right side of engine)
- Oxygen sensor 2/2 (left side of engine)
- Pnk/red
- Powertrain control module (left rear of engine compt)
- Red
- Relay block (left side of engine compt)
- Rly out
- S/c sig 2
- S/c sw gnd
- S103 (in front of left shock tower)
- S106 (in breakout to manifold tuning valve solenoid)
- S110
- S114
- S123
- Sens gnd
- Shift interlock system
- Short runner valve solenoid (top front of left cylinder bank)
- Sig 1
- Sig 2
- Srv ctrl
- Srv sig
- Starting/ charging system
- Steering control module (on steering column)
- Sw gnd
- T44
- Totally integrated power module (left side of engine compt)
- V71
- V72
- V937
3.5L, Engine Performance Wiring Diagram (2 of 5) for Chrysler Sebring Touring 2008
List of elements for 3.5L, Engine Performance Wiring Diagram (2 of 5) for Chrysler Sebring Touring 2008:
- (at left
- (at left rear quarter panel)
- (at left rear quarter panel) g303
- (in brake fluid reservoir) brake fluid level sensor
- (inside left front fender) s126
- (right side of front bumper beam) ambient air temperature sensor
- (top of brake pedal) stop lamp switch
- Aat
- App sig 2
- Awd
- B(+)
- B20
- Brake fluid level
- C10
- C11
- Ctrl
- Ctrl out
- Electronics
- Esm sig
- Evap monitor system switch (under left rear of vehicle)
- Except awd
- F202
- Fuel level sig 1 fuel pump module
- Fuel lvl sig 1
- Fuel lvl sig 2
- Fuel pimp ctl out
- Fuel pump
- Fuel pump control module
- Fuel pump ctl out
- Fuel pump ctrl
- Fuse 10a
- G111 (on left shock tower)
- G302
- G303
- G31
- G931
- Ground
- Hot at all times
- Ign sw out (run- start)
- Instrument cluster system
- K107
- K29
- K31
- Kick panel)
- L53
- Out
- Powertrain control module (left rear of engine compt)
- Red
- Rtn
- S/c sig 1
- S120 (behind left headlight)
- Sig
- Starter
- Starter ctrl
- Stop lamp sw out
- T15
- T16
- T752
- Totally integrated power module (left side of engine compt)
- Trans
- V71
- Z916
3.5L, Engine Performance Wiring Diagram (3 of 5) for Chrysler Sebring Touring 2008
List of elements for 3.5L, Engine Performance Wiring Diagram (3 of 5) for Chrysler Sebring Touring 2008:
- (on left shock tower) g111
- 2-4 lr ctrl
- 2-4 press sw
- 2-4 pressure sig
- 4c sol
- 5v sply
- Dc ctrl
- Dc press sw
- Dc pressure sig
- Dc sol
- Early production: z902 late production: z931
- Emcc sol
- Emcc vfs ctrl
- Ground
- Input speed sig
- L/r ctrl
- L/r press sw
- L/r pressure sig
- Lc ctrl
- Lc press sw
- Lc pressure sig
- Lc sol
- Lp vfs ctrl
- Lpvfs sig
- Lr sol
- Od ctrl
- Od press sw
- Od pressure sig
- Od sol
- Out speed sig
- Powertrain control module (left rear of engine compt)
- S172 (in breakout to c106, above transmission)
- Sens gnd
- Sens ground
- T118
- T13
- T14
- T15
- T16
- T19
- T20
- T38
- T41
- T42
- T47
- T50
- T52
- T54
- T59
- T60
- T80
- T81
- T82
- T83
- T84
- T85
- Trans ctrl
- Trans ctrl out
- Trans temp sig
- Transfer spd sig
- Transmission solenoid/trs assembly (left side of transaxle)
- Transmission temperature sensor
- Trs t1 sig
- Trs t3 sig
- Trs t41 sig
- Trs t42 sig
- Ud ctrl
- Ud sol
- Vfs sol
3.5L, Engine Performance Wiring Diagram (4 of 5) for Chrysler Sebring Touring 2008
List of elements for 3.5L, Engine Performance Wiring Diagram (4 of 5) for Chrysler Sebring Touring 2008:
- (near throttle body) s191
- (rear of transaxle case) output speed sensor
- (rear of transaxle) transfer speed sensor
- (top of transaxle) input speed sensor
- 5v sply
- Camshaft position sensor 1 (top front of left cylinder bank)
- Egr valve assembly (rear of engine)
- Engine coolant temperature sensor (top front of engine)
- G111 (on left shock tower)
- Gnd
- Intake air temperature sensor (on intake manifold)
- Manifold tuning valve solenoid (top right front of engine)
- Map sensor (top right rear of engine)
- Mtv ctrl
- Mtv sig
- S171 (in breakout to pcm c4)
- S181 (in breakout to c101 & pcm c2)
- S182 (in injector harness, below throttle body)
- S199
- Sens gnd
3.5L, Engine Performance Wiring Diagram (5 of 5) for Chrysler Sebring Touring 2008
List of elements for 3.5L, Engine Performance Wiring Diagram (5 of 5) for Chrysler Sebring Touring 2008:
- (on left shock tower) g111
- (top of left cylinder bank) fuel injectors
- (top of left valve cover) ignition coils
- (top of right cylinder bank) fuel injectors
- (top of right valve cover) ignition coils
- 5v sply
- Ckp sig
- Cmp sig
- Coil 1 ctrl
- Coil 2 ctrl
- Coil 3 ctrl
- Coil 4 ctrl
- Coil 5 ctrl
- Coil 6 ctrl
- Crankshaft position sensor (right rear of engine)
- Ect sig
- Egr ctrl
- Egr sig
- Etc motor (+)
- Etc motor (-)
- Etc mtr (+)
- Etc mtr (-)
- F855
- Gen field ctrl
- Iat sig
- Ignition capacitor 1 (top rear of engine)
- Inj 1 ctrl
- Inj 2 ctrl
- Inj 3 ctrl
- Inj 4 ctrl
- Inj 5 ctrl
- Inj 6 ctrl
- K10
- K11
- K12
- K122
- K124
- K126
- K13
- K136
- K14
- K15
- K16
- K17
- K18
- K19
- K199
- K20
- K21
- K22
- K24
- K34
- K35
- K38
- K41
- K42
- K43
- K44
- K58
- K900
- K902
- K922
- K942
- K99
- Knock sensor (below throttle body)
- Ks rtn
- Ks sig
- Map sig
- Mtv ctrl
- Nca
- O2 1/1 heater ctrl
- O2 1/1 sig
- O2 2/1 heater ctrl
- O2 2/1 sig
- O2 rtn (up)
- Oxygen sensor 1/1 (right front of engine)
- Oxygen sensor 2/1 (left side of engine)
- Powertrain control module (left rear of engine compt)
- S184 (in breakout to c101 & pcm c2)
- S190 (near breakout to ignition coil 5)
- S192 (below throttle body)
- Sens ground
- Starting/ charging system
- Throttle body (top rear of engine)
- Tp sens gnd
- Tp sens ground
- Tp sig 1
- Tp sig 2
Čeština
Dansk
Deutsch
Ελληνικά
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
日本語
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
