ENGINE PERFORMANCE – Oldsmobile Intrigue GLS 1999 – SYSTEM WIRING DIAGRAMS

ENGINE PERFORMANCE

3.5L

3.5L VIN H, Engine Performance Wiring Diagrams (1 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.5L VIN H, Engine Performance Wiring Diagrams (1 of 4) for Oldsmobile Intrigue GLS 1999:

• (bolted to rear engine mount) air solenoid valve
• (engine harn, 10 cm from pcm breakout)
• (engine harn, 13 cm from injector 1 breakout)
• (engine harn, 8 cm from pcm breakout)
• (near left headlamp assembly) secondary air injection pump
• (on transaxle stud)
• (pin 10-11 not used)
• (pin 14-15 not used)
• (pin 21 & 23-27 not used)
• (pin 39-42 not used)
• (pin 49-52 not used)
• (pin 66-67 not used)
• 1-2 ss valve control
• 2-3 ss valve control
• A/t iss sensor high
• A/t iss sensor low
• Air pump fuse 30a
• Air pump relay
• Air sol vlv ctrl
• Anti-lock brake system
• C1 d10
• Camshaft position sensor (right front corner of engine)
• Ckp sens a
• Ckp sens b
• Cmp sens sig
• Connector (under left side of dash, right of steering column)
• Cooling fans system
• Crankshaft position sensor (left side of engine)
• Cruise control system
• Cruise disable output
• Data link
• Ecm fuse 10a
• Ect sensor signal
• Egr pintle sensor gnd
• Egr val control (gnd)
• Eng emis fuse 10a
• Evap purge val drviver
• Front bank ignition control module (top of left valve cover)
• Fuel inj 1 driver
• Fuel inj 2 driver
• Fuel inj 4 driver
• Fuel inj 5 driver
• Fuel inj 6 driver
• Fuse block
• G101 (right side of front end upper tie bar)
• G129
• High speed fans control
• Hos1 low
• Hos2 low
• Hot at all times
• Hot in off, run bulb test, or start
• Hot in run, bulb test or start
• Iac coil b high
• Iat sensor ground
• Ig ctrl 1
• Ig ctrl 2
• Ig ctrl 3
• Ig ctrl 4
• Ig ctrl 5
• Ig ctrl 6
• Ign 0 cluster fuse 10a
• Ignition wake up power
• Knock sensor (next to oil pressure switch)
• Knock sensor signal 2
• Low speed fans control
• Maf sensor signal
• Map sensor signal
• Nca
• Pcm ground
• Pnk
• Pnk f
• Power (battery)
• Powertrain control module (left front side of eng compt, in air cleaner assembly)
• Psp sw input
• Rear bank ignition control module (top of right valve cover)
• Red
• Ref low
• S106
• S108
• S147
• S168
• S171
• Serial data (class 2)
• Spark plugs
• Splice pack sp250 (right side of steering column)
• Tan
• Tcc brake switch input
• Tp sensor signal
• Tr switch input b
• Trans fluid press sw a
• Underhood accessory wiring junction block
• Vcc torque req
• Vss high
• Vss low
• Vss output

3.5L VIN H, Engine Performance Wiring Diagrams (2 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.5L VIN H, Engine Performance Wiring Diagrams (2 of 4) for Oldsmobile Intrigue GLS 1999:

• (on transaxle stud)
• Evaporative emissions canister purge solenoid valve (top left side of eng, near center of valve cover)
• Evaporative emissions canister vent solenoid valve (behind left side of rear fascia splash shield, in wheelwell)
• F/injr fuse 25 15a
• F/injr fuse 28 15a
• Fuel injectors
• G129
• Hot in run or start
• Pnk
• Power steering cut-out switch (on power steering line)
• Red
• S106
• S109
• S169
• Stop- light switch (on brake pedal support c2 bracket)
• Tan
• Transaxle range switch (top right rear of transaxle)
• Underhood accessory wiring junction block
• Underhood electrical center (mounted to right c1 strut tower)
• Vehicle speed sensor (lower right side of eng compt, on transaxle)

3.5L VIN H, Engine Performance Wiring Diagrams (3 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.5L VIN H, Engine Performance Wiring Diagrams (3 of 4) for Oldsmobile Intrigue GLS 1999:

• (body harn, front of rear compt)
• (bottom of engine oil pan) engine oil level indicator switch
• (eng harn, 6 cm from inj 1 breakout)
• (eng harn, near air cleaner, 16 cm from pcm breakout)
• (eng harn, near air cleaner, 20 cm from pcm breakout)
• (in exhaust system, behind catalytic converter) heated oxygen sensor (ho2s) no2
• (in right side of exhaust manifold) heated oxygen sensor (ho2s) no1
• (on throttle body assembly) idle air control (iac) valve
• (on transaxle
• (part of throttle body assembly) mass air- flow sensor
• (right lower rear of eng, above transaxle) engine oil pressure indicator switch
• A tan
• A/c refrigerant pressure sensor (on left side of eng compt, on accumulator)
• C pnk
• D pnk
• Engine coolant temperature (ect) sensor (right rear of eng, below throttle body)
• Exhaust gas recirculation valve (top rear of eng, near throttle body)
• Fuel tank pressure sensor (in fuel tank)
• G129
• Instrument cluster
• Intake air temperature (iat) sensor (left rear of eng compt, in air cleaner duct)
• Malfunction indicator lamp
• Manifold absolute pressure sensor (top right of eng, near throttle body assembly)
• Nca
• Pnk
• Red
• S105
• S107
• S122
• S167
• S409
• Stud)
• Tan
• Throttle position sensor (on throttle body assembly)

3.5L VIN H, Engine Performance Wiring Diagrams (4 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.5L VIN H, Engine Performance Wiring Diagrams (4 of 4) for Oldsmobile Intrigue GLS 1999:

• (on transaxle stud)
• (pin 12-15 not used)
• (pin 20-21 not used)
• (pin 30-32 not used)
• (pin 40-41 not used)
• (pin 47-48 not used)
• (pin 51-54 not used)
• (pin 62 & 64-65 not used)
• (pin 70-71not used)
• (right rear shelf)
• 1-2 shift solenoid
• 2-3 shift solenoid
• 5v ref a
• A/c compress clutch rly
• A/c refrig press signal
• A/c request signal
• A/t iss solenoid
• A11
• Air conditioning system
• Anti-lock brake system
• Auto transaxle fluid temperature sensor
• Automatic transaxle
• Automatic transaxle fluid pressure manual valve position switch
• Ckp/cmp sens pwr
• Cluster fuse 10a
• Crank
• Crank signal fuse 10a
• Cruise control system
• Cruise engaged input
• D10
• Ect sensor signal
• Egr pintle position signal
• Egr val ign positive volt
• Eng oil level ind in
• Eng oil press sensor sig
• Evap can vent sol driver
• F/pmp fuse 15a
• F/pump relay
• Fuel inj 3 driver
• Fuel level sensor
• Fuel level sensor input
• Fuel pump
• Fuel pump relay control
• Fuel tank
• Fuel tank press signal
• Fuse block
• G129
• G313
• Gen terminal f output
• Gen terminal l output
• Ho2s 1 signal
• Ho2s 2 signal
• Hot at all times
• Hot in run, bulb test or start
• Hot in run, bulb test, or start
• Hot in start
• Iac coil a high
• Iac coil a low
• Iac coil b low
• Iat sensor signal
• Ignition positive volt (2)
• Map sensor signal
• Mil control
• Oxy sen fuse 15a
• Pc sol valve high
• Pc sol valve low
• Pc solenoid
• Pcm- bcm fuse 10a
• Pnk
• Powertrain control module (left front side of eng compt, in air cleaner assembly)
• Red
• Ref lo
• S106
• S234
• Sensor ground
• Starter enable control
• Starting/ charging system
• Tach out
• Tan
• Tcc pwm solenoid
• Tcc release switch input
• Tcc sol valve control
• Tft sensor signal
• Torque del
• Tp sens or signal
• Tr switch input a
• Tr switch input c
• Tr switch input d
• Trans abs fuse 10a
• Trans fluid press sw b
• Underhood accessory wiring junction block

3.8L

3.8L VIN K, Engine Performance Wiring Diagrams (1 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.8L VIN K, Engine Performance Wiring Diagrams (1 of 4) for Oldsmobile Intrigue GLS 1999:

• (icm harn, top of eng, near ign control module)
• (not used)
• (on transaxle stud)
• (pin 10-11 not used)
• (pin 14-15 not used)
• (pin 21 & 23-27 not used)
• (pin 39-42 not used)
• (pin 49-52 not used)
• (pin 66-67 not used)
• (top front of engine)
• 1-2 ss valve control
• 18x ref signal
• 2-3 ss valve control
• 3x ref signal
• A/t iss sensor high
• A/t iss sensor low
• Battery feed
• Bypass
• Camshaft position sensor (cmp) (front of eng, above crankshaft pulley)
• Cmp signal
• Cooling fans system
• Crankshaft position (ckp) sensor (front of eng, behind harmonic balancer)
• Cruise control system
• Cruise disable output
• Data link connector (dlc) (under left side of dash, right of steering column)
• Dfi fuse 25 15a
• Ecm fuse 10a
• Ect sensor signal
• Egr control gnd
• Egr sensor gnd
• Eng emis fuse 10a
• Evap can purge control
• F/injr fuse 15a
• Fuel inj 1 control
• Fuel inj 2 control
• Fuel inj 4 control
• Fuel inj 5 control
• Fuel inj 6 control
• Fuse block (behind right side of dash, in right door opening)
• G125
• G129
• High speed fans control
• Ho2s 1 low
• Ho2s 2 low
• Hot at all times
• Hot in acc, on or start
• Hot in on or start
• Hot in on, bulb test or start
• Iac coil b high
• Iat sensor ground
• Ic control
• Ign 0 fuse 10a
• Ignition control module (icm) (top front of eng)
• Ignition feed
• Knock sensor 1 (lower right side of eng, below exhaust manifold)
• Knock sensor 2 (left side of eng, in front of starter)
• Knock sensor signal 1
• Knock sensor signal 2
• Low speed fans control
• Maf sensor signal
• Map sensor signal
• Pcm ground
• Pnk
• Pnk p
• Powertrain control module (pcm) (left front side of eng compt, in air cleaner assembly)
• Ref low
• S106
• S144
• S145
• S270
• Serial data (class 2)
• Spark plugs
• Splice pack sp250
• Tan
• Tcc brake switch input
• Tp sensor signal
• Tr switch input c
• Trans fluid press sw a
• Underhood accessory wiring junction block (mounted to right strut tower)
• Vss high
• Vss low
• Vss output

3.8L VIN K, Engine Performance Wiring Diagrams (2 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.8L VIN K, Engine Performance Wiring Diagrams (2 of 4) for Oldsmobile Intrigue GLS 1999:

• (on transaxle stud)
• Evaporative emissions (evap) canister purge solenoid valve (top left side of eng, near center of valve cover)
• Evaporative emissions (evap) canister vent solenoid valve (behind left side of rear fascia splash shield, in wheelwell)
• Fuel injectors
• G129
• Pnk
• S105
• S106
• S109
• Stop- light switch (on brake pedal support c2 bracket)
• Tan
• Transaxle range switch (on top right rear on transaxle)
• Underhood accessory wiring junction block (mounted to right strut tower)
• Vehicle speed sensor (vss) (lower right side of eng compt, on transaxle)

3.8L VIN K, Engine Performance Wiring Diagrams (3 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.8L VIN K, Engine Performance Wiring Diagrams (3 of 4) for Oldsmobile Intrigue GLS 1999:

• (body harn, near front of rear compt)
• (eng harn, left side of eng compt, 19 cm from transaxle wiring breakout)
• (eng harn, left top front of eng)
• (eng harn, near air cleaner, 4 cm from pcm breakout)
• (in exhaust system, rear of catalytic converter) heated oxygen sensor (ho2s) 2 sensor
• (in right side exhaust manifold) heated oxygen sensor (ho2s) 1 sensor
• (lower right side of eng, above transaxle) engine oil pressure indicator switch
• (on bottom of engine oil pan) engine oil level indicator switch
• (on throttle body assembly) idle air control (iac) valve
• (on transaxle stud)
• (top rear of eng, part of throttle body assembly) mass airflow (maf) sensor
• A tan
• A/c refrigerant pressure sensor (on left side of eng compt, on accumulator)
• D pnk
• Engine coolant temperature (ect) sensor (top left side of eng, below throttle body)
• Exhaust gas recirculation (egr) valve (top rear of eng, near throttle body)
• Fuel tank pressure sensor (in fuel tank)
• G129
• Instrument cluster
• Intake air temperature (iat) sensor (left front of eng compt, in air cleaner duct)
• Malfunction indicator lamp
• Manifold absolute pressure (map) sensor (top of eng, on front of intake manifold)
• Nca
• Pnk
• S105
• S107
• S122
• S167
• S409
• Tan
• Throttle position (tp) sensor (on throttle body assembly)

3.8L VIN K, Engine Performance Wiring Diagrams (4 of 4) for Oldsmobile Intrigue GLS 1999

List of elements for 3.8L VIN K, Engine Performance Wiring Diagrams (4 of 4) for Oldsmobile Intrigue GLS 1999:

• (front of right front door sill)
• (on transaxle stud)
• (pin 12-15 not used)
• (pin 30-32 not used)
• (pin 40-41 not used)
• (pin 47-48 not used)
• (pin 51-54 not used)
• (pin 62 & 64-65 not used)
• (pin 70-75 not used)
• (pin 8-9 not used)
• 1-2 b shift solenoid
• 2-3 shift solenoid
• 5v ref a
• 5v ref b
• A/c compress clutch rly
• A/c refrig press signal
• A/c request signal
• A/t iss solenoid
• A11
• Air conditioning system
• Auto transaxle fluid temperature sensor
• Automatic transaxle fluid pressure manual valve position switch
• B tcc solenoid
• Cluster fuse 10a
• Crank signal fuse 10a
• Cruise control system
• Cruise engaged input
• D10
• Ect sensor signal
• Egr pintle position signal
• Egr val control
• Eng oil level ind in
• Eng oil press sensor sig
• Evap can vent valve
• F/pmp fuse 15a
• F/pump relay
• Fuel inj 3 driver
• Fuel level sensor
• Fuel level sensor input
• Fuel pump
• Fuel pump relay control
• Fuel tank
• Fuel tank press signal
• Fuse block (behind right side of dash, in right door opening)
• G129
• G316
• Gen terminal f output
• Gen terminal l output
• Ho2s 1 signal
• Ho2s 2 signal
• Hot at all times
• Hot in acc, on or start
• Hot in on or start
• Hot in on, bulb test, or start
• Hot in start
• Iac coil a high
• Iac coil a low
• Iac coil b low
• Iat sensor signal
• Ignition feed
• Map sensor signal
• Mil control
• Oxy sen fuse 15a
• Pc sol valve high
• Pc sol valve low
• Pcm- bcm fuse 10a
• Pnk
• Powertrain control module (pcm) (left front side of eng compt, in air cleaner assembly)
• Ps solenoid
• Red
• S106
• S234
• Sensor ground
• Starter enable control
• Starting/ charging system
• Tan
• Tcc release switch input
• Tcc sol valve control
• Tft sensor signal
• Tp sens or signal
• Trans fluid press sw b
• Trans fluid press sw c
• Trans fuse 26 10a
• Trans range a
• Trans range p
• Transaxle
• Transaxle range b
• Underhood accessory wiring junction block (mounted to right strut tower)